Lennart Reuter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lennart Reuter has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Hubert Andreas Gasteiger
Technical University of Munich
8 shared publications - Jonas L. S. Dickmanns
Technical University of Munich, Germany; TUM School of Natural Sciences, Department of Chemistry and Catalysis Research Center, Chair of Technical Electrochemistry
5 shared publications - Andreas Jossen
Technical University of Munich
3 shared publications - Filippo Maglia
BMW Group
3 shared publications - Louis Hartmann
Chair of Technical Electrochemistry and Catalysis Research Center
3 shared publications - Roland Jung
BMW Group, Munich, Germany
3 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (19) , 190517
Correlating Formation Conditions to Graphite Resistance, Rate Capability, Cycling Stability, and Gassing in FEC-Containing Li-Ion Batteries
The beneficial effect of fluoroethylene carbonate (FEC) as a co-solvent and electrolyte additive on the cycle life of lithium-ion batteries, particularly those employing high-voltage cathode active materials, has been demonstrated in numerous studies. To further elucidate the effect of varying FEC content, as well as the impact of formation temperature on the properties of the graphite SEI, we performed formation between 10 °C and 60 °C with cells containing either 2 wt% or 20 wt% FEC in LP-57. The irreversible capacity loss due to SEI formation and the arising intercalation resistance (representing the sum of charge-transfer and SEI resistance), determined by means of electrochemical impedance spectroscopy, increased with higher temperature and FEC content. The impact of both quantities on the full-cell performance was assessed in coin and T-cells, revealing enhanced cycling stability for cells that were formed at elevated temperatures, despite a higher susceptibility to lithium plating accompanied by a decreased rate capability for their T-cell analogues when evaluating the rate performance. Employing on-line electrochemical mass spectrometry (OEMS), we further show that higher temperatures and higher FEC contents give rise to a more pronounced, but also more condensed, gas evolution during the initial cycles.
- 12 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (19) , 190517
Open AccessCorrelating Formation Conditions to Graphite Resistance, Rate Capability, Cycling Stability, and Gassing in FEC-Containing Li-Ion Batteries
The beneficial effect of fluoroethylene carbonate (FEC) as a co-solvent and electrolyte additive on the cycle life of lithium-ion batteries, particularly those employing high-voltage cathode active materials, has been demonstrated in numerous studies. To further elucidate the effect of varying FEC content, as well as the impact of formation temperature on the properties of the graphite SEI, we performed formation between 10 °C and 60 °C with cells containing either 2 wt% or 20 wt% FEC in LP-57. The irreversible capacity loss due to SEI formation and the arising intercalation resistance (representing the sum of charge-transfer and SEI resistance), determined by means of electrochemical impedance spectroscopy, increased with higher temperature and FEC content. The impact of both quantities on the full-cell performance was assessed in coin and T-cells, revealing enhanced cycling stability for cells that were formed at elevated temperatures, despite a higher susceptibility to lithium plating accompanied by a decreased rate capability for their T-cell analogues when evaluating the rate performance. Employing on-line electrochemical mass spectrometry (OEMS), we further show that higher temperatures and higher FEC contents give rise to a more pronounced, but also more condensed, gas evolution during the initial cycles.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 500
Effects of Electrolyte and Binder on Gas Evolution, Irreversible Capacity, and SEI Molar Mass during Formation of Graphite Electrodes for Lithium-Ion Batteries
The lifetime of lithium-ion batteries (LiBs) is strongly influenced by the formation of a stable solid-electrolyte interphase (SEI), a passivating layer that forms on the negative electrode due to electrolyte reduction in the initial cycles.1,2 The SEI consists of decomposition products from commonly used carbonate-based electrolyte components, such as ethylene carbonate (EC), ethyl methyl carbonate (EMC), diethyl carbonate (DEC), dimethyl carbonate (DMC), and the LiPF6 conductive salt.3,4 Additionally, electrolyte additives can alter the SEI composition and thickness.5 SEI formation is accompanied by gas evolution,6 irreversible capacity loss,7 and electrode mass changes,8 all of which are strongly influenced by the choice of the electrolyte and electrode composition. A detailed understanding of these processes is essential for optimizing anode performance and designing formation protocols for commercial cells.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 500
Effects of Electrolyte and Binder on Gas Evolution, Irreversible Capacity, and SEI Molar Mass during Formation of Graphite Electrodes for Lithium-Ion Batteries
The lifetime of lithium-ion batteries (LiBs) is strongly influenced by the formation of a stable solid-electrolyte interphase (SEI), a passivating layer that forms on the negative electrode due to electrolyte reduction in the initial cycles.1,2 The SEI consists of decomposition products from commonly used carbonate-based electrolyte components, such as ethylene carbonate (EC), ethyl methyl carbonate (EMC), diethyl carbonate (DEC), dimethyl carbonate (DMC), and the LiPF6 conductive salt.3,4 Additionally, electrolyte additives can alter the SEI composition and thickness.5 SEI formation is accompanied by gas evolution,6 irreversible capacity loss,7 and electrode mass changes,8 all of which are strongly influenced by the choice of the electrolyte and electrode composition. A detailed understanding of these processes is essential for optimizing anode performance and designing formation protocols for commercial cells.
- Open Access
- 7 August 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Changes in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part II: Impact of State-of-Charge
The crystalline volume change of graphite upon lithiation and delithiation is reported to lead to a change in the thickness and porosity of porous electrodes. Using electrochemical impedance spectroscopy, this study resolved the concomitant state-of-charge (SOC) dependent change of the ionic pore resistance (R_Ion ) of graphite electrodes via measurements conducted at low temperatures and stack pressures of 0.2 and 1.0 MPa. The pressure-dependent results reveal an increase of R_Ion upon complete lithiation of up to ~32% and ~45% at the lower and higher pressure, respectively. This data was combined with literature data on the volumetric expansion of graphite particles obtained from X-ray diffraction measurements to reveal a significant decrease in porosity upon lithiation. From there, the thickness changes of the graphite electrodes can be calculated. Inferable from this is a significant SOC-dependent variation in the MacMullin number (>30%), a crucial simulation parameter, of up to +40%. We observe a net pore volume decrease upon lithiation, particularly for a higher stack pressure. The reduction in the pore volume of up to 15% induces an electrolyte pumping effect. The study transfers these insights obtained from laboratory-type cells to commercial cells and addresses the recently described effect of electrolyte motion-induced salt inhomogeneity (EMSI).
- 7 August 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessChanges in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part II: Impact of State-of-Charge
The crystalline volume change of graphite upon lithiation and delithiation is reported to lead to a change in the thickness and porosity of porous electrodes. Using electrochemical impedance spectroscopy, this study resolved the concomitant state-of-charge (SOC) dependent change of the ionic pore resistance (R_Ion ) of graphite electrodes via measurements conducted at low temperatures and stack pressures of 0.2 and 1.0 MPa. The pressure-dependent results reveal an increase of R_Ion upon complete lithiation of up to ~32% and ~45% at the lower and higher pressure, respectively. This data was combined with literature data on the volumetric expansion of graphite particles obtained from X-ray diffraction measurements to reveal a significant decrease in porosity upon lithiation. From there, the thickness changes of the graphite electrodes can be calculated. Inferable from this is a significant SOC-dependent variation in the MacMullin number (>30%), a crucial simulation parameter, of up to +40%. We observe a net pore volume decrease upon lithiation, particularly for a higher stack pressure. The reduction in the pore volume of up to 15% induces an electrolyte pumping effect. The study transfers these insights obtained from laboratory-type cells to commercial cells and addresses the recently described effect of electrolyte motion-induced salt inhomogeneity (EMSI).
- Open Access
- 1 July 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (7) , 070513
Changes in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part I: Impact of Formation and SEI
With the interest in achieving higher gravimetric and volumetric energy densities in lithium-ion batteries, increasing the electrode loading and reducing its thickness—and consequently porosity—while maintaining low tortuosity is desirable. Achieving high power density requires a thorough understanding of these structural parameters of thick graphite electrodes and their changes during the formation of the solid-electrolyte-interphase (SEI). Graphite electrodes with loadings of ∼ 10 mg cm − 2 and pristine porosities ranging from 20–50% underwent formation at 45 °C in LP57 + 2% VC electrolyte. The ionic pore resistance after formation was quantified in non-blocking conditions using a μ-reference electrode and measuring electrochemical impedance spectroscopy at −5 °C. Upon formation, the ionic resistance of the graphite electrodes increased by up to 25%, which was quantitatively related to specific changes in electrode thickness, porosity, and tortuosity. The change in electrode thickness depended on the pristine porosity and increased by up to ∼11%. Mercury intrusion porosimetry revealed a decrease in porosity for initially high-porosity electrodes and an increase for those with low pristine porosity. The tortuosity of the electrodes increased by up to ∼10% upon formation. The thickness and density of the SEI were determined using a combination of pycnometry and mass-gain measurements, yielding 16–20 nm and ∼ 1.07 g cm − 3 , respectively.
- 1 July 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (7) , 070513
Open AccessChanges in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part I: Impact of Formation and SEI
With the interest in achieving higher gravimetric and volumetric energy densities in lithium-ion batteries, increasing the electrode loading and reducing its thickness—and consequently porosity—while maintaining low tortuosity is desirable. Achieving high power density requires a thorough understanding of these structural parameters of thick graphite electrodes and their changes during the formation of the solid-electrolyte-interphase (SEI). Graphite electrodes with loadings of ∼ 10 mg cm − 2 and pristine porosities ranging from 20–50% underwent formation at 45 °C in LP57 + 2% VC electrolyte. The ionic pore resistance after formation was quantified in non-blocking conditions using a μ-reference electrode and measuring electrochemical impedance spectroscopy at −5 °C. Upon formation, the ionic resistance of the graphite electrodes increased by up to 25%, which was quantitatively related to specific changes in electrode thickness, porosity, and tortuosity. The change in electrode thickness depended on the pristine porosity and increased by up to ∼11%. Mercury intrusion porosimetry revealed a decrease in porosity for initially high-porosity electrodes and an increase for those with low pristine porosity. The tortuosity of the electrodes increased by up to ∼10% upon formation. The thickness and density of the SEI were determined using a combination of pycnometry and mass-gain measurements, yielding 16–20 nm and ∼ 1.07 g cm − 3 , respectively.
- Open Access
- 1 June 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (6) , 060536
Temperature Dependence of the Chemical vs the Electrochemical Electrolyte Oxidation in Lithium-Ion Batteries with Ni-Rich CAMs: Gas Evolution, Salt Decomposition, and Metal Dissolution
Operating lithium-ion batteries (LIBs) to high charging cut-off potentials allows us to accommodate a further push in energy density. However, it requires a thorough understanding of the interplay and temperature dependence of parasitic reactions that aggravate the aging of the electrolyte and the cathode/anode electrodes. In the present study we investigated the interplay of the chemical and the electrochemical electrolyte oxidation, how they are related to the dissolution of transition metal (TM) ions from the cathode active material (CAM), and how they shift or accelerate with temperature. Through an optimized electrochemical protocol an excellent potential dependence of the gas evolution of a LiNi0.80Co0.15Al0.05O2 (NCA) charged against a free-standing graphite on a lithium metal electrode in a LP47 electrolyte was achieved. We identified O2 and PF5 gas as suitable proxies for the chemical and electrochemical electrolyte oxidation, respectively. Both processes are separated by at least 300 mV over a temperature range from 10 to 45 °C. Through temperature-dependent operando hard X-ray absorption spectroscopy measurements and their comparison with the gassing results, it will be shown, that the electrochemical oxidation of the electrolyte is directly linked to the dissolution of TMs, while the chemical electrolyte oxidation mainly leaves the transition metal dissolution unaffected.
- 1 June 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (6) , 060536
Open AccessTemperature Dependence of the Chemical vs the Electrochemical Electrolyte Oxidation in Lithium-Ion Batteries with Ni-Rich CAMs: Gas Evolution, Salt Decomposition, and Metal Dissolution
Operating lithium-ion batteries (LIBs) to high charging cut-off potentials allows us to accommodate a further push in energy density. However, it requires a thorough understanding of the interplay and temperature dependence of parasitic reactions that aggravate the aging of the electrolyte and the cathode/anode electrodes. In the present study we investigated the interplay of the chemical and the electrochemical electrolyte oxidation, how they are related to the dissolution of transition metal (TM) ions from the cathode active material (CAM), and how they shift or accelerate with temperature. Through an optimized electrochemical protocol an excellent potential dependence of the gas evolution of a LiNi0.80Co0.15Al0.05O2 (NCA) charged against a free-standing graphite on a lithium metal electrode in a LP47 electrolyte was achieved. We identified O2 and PF5 gas as suitable proxies for the chemical and electrochemical electrolyte oxidation, respectively. Both processes are separated by at least 300 mV over a temperature range from 10 to 45 °C. Through temperature-dependent operando hard X-ray absorption spectroscopy measurements and their comparison with the gassing results, it will be shown, that the electrochemical oxidation of the electrolyte is directly linked to the dissolution of TMs, while the chemical electrolyte oxidation mainly leaves the transition metal dissolution unaffected.
- Open Access
- 1 February 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (2) , 020537
Investigating the Impact of Various Binder Contents and Compression on Graphite Single-Electrode Dilatometry Measurements
Knowledge about how particle volume changes impact the electrode thickness and microstructural properties like porosity, especially as a function of binder types and contents, is crucial to improving battery design. Single-electrode electrochemical dilatometry provides insights into electrode thickness change during operation. However, commercially available setups have yet to be able to apply sufficient pressure on electrodes to replicate conditions in commercial batteries. This work aims to incorporate a wave spring washer into a commercially available single-electrode electrochemical dilatometer to apply additional force onto the working electrode. Using this setup, the impact of the binder composition on electrode thickness change was investigated using graphite electrodes with different amounts and ratios of styrene-butadiene rubber and carboxymethyl cellulose. It was shown that the electrode volume change is consistently lower than that of the crystallites as obtained by X-ray diffraction in the literature. It is further demonstrated that irreversible thickness change decreases with increasing binder content, indicating that a higher binder content helps prevent particle restructuring during cycling. Lastly, the modified setup exhibits significantly higher reliability than the commercial setup with low pressure, which we relate to electrode bending during lithiation.
- 1 February 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (2) , 020537
Open AccessInvestigating the Impact of Various Binder Contents and Compression on Graphite Single-Electrode Dilatometry Measurements
Knowledge about how particle volume changes impact the electrode thickness and microstructural properties like porosity, especially as a function of binder types and contents, is crucial to improving battery design. Single-electrode electrochemical dilatometry provides insights into electrode thickness change during operation. However, commercially available setups have yet to be able to apply sufficient pressure on electrodes to replicate conditions in commercial batteries. This work aims to incorporate a wave spring washer into a commercially available single-electrode electrochemical dilatometer to apply additional force onto the working electrode. Using this setup, the impact of the binder composition on electrode thickness change was investigated using graphite electrodes with different amounts and ratios of styrene-butadiene rubber and carboxymethyl cellulose. It was shown that the electrode volume change is consistently lower than that of the crystallites as obtained by X-ray diffraction in the literature. It is further demonstrated that irreversible thickness change decreases with increasing binder content, indicating that a higher binder content helps prevent particle restructuring during cycling. Lastly, the modified setup exhibits significantly higher reliability than the commercial setup with low pressure, which we relate to electrode bending during lithiation.
- Open Access
- 1 October 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (10) , 100524
3-Electrode Setup for the Operando Detection of Side Reactions in Li-Ion Batteries: The Quantification of Released Lattice Oxygen and Transition Metal Ions from NCA
Detecting parasitic side reactions is paramount for developing stable cathode active materials (CAMs) for Li-ion batteries. This study presents a method for the quantification of released lattice oxygen and transition metal ions (TMII+ ions). It is based on a 3-electrode cell design employing a Vulcan carbon-based sense electrode (SE) that is held at a controlled voltage against a partially delithiated lithium iron phosphate (LFP) counter electrode (CE). At this SE, reductive currents can be measured while polarizing a CAM working electrode (WE), here a LiNi0.80Co0.15Al0.05O2 (NCA), against the same LFP CE. In voltammetric scans, we show how the SE potential can be selected to specifically detect a given side reaction during CAM charge/discharge, allowing, e.g., to discriminate between lattice oxygen and dissolved TMs. Furthermore, it is shown via online electrochemical mass spectrometry (OEMS) that O2 reduction in the here-used LP47 electrolyte consumes ∼2.3 electrons/O2. Using this value, the lattice oxygen release deduced from the 3-electrode setup upon charging of the NCA WE is in good agreement with OEMS measurements up to NCA potentials >4.65 VLi. At higher potentials, the contributions from the reduction of TMII+ ions can be quantified by comparing the integrated SE current with the O2 evolution from OEMS.
- 1 October 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (10) , 100524
Open Access3-Electrode Setup for the Operando Detection of Side Reactions in Li-Ion Batteries: The Quantification of Released Lattice Oxygen and Transition Metal Ions from NCA
Detecting parasitic side reactions is paramount for developing stable cathode active materials (CAMs) for Li-ion batteries. This study presents a method for the quantification of released lattice oxygen and transition metal ions (TMII+ ions). It is based on a 3-electrode cell design employing a Vulcan carbon-based sense electrode (SE) that is held at a controlled voltage against a partially delithiated lithium iron phosphate (LFP) counter electrode (CE). At this SE, reductive currents can be measured while polarizing a CAM working electrode (WE), here a LiNi0.80Co0.15Al0.05O2 (NCA), against the same LFP CE. In voltammetric scans, we show how the SE potential can be selected to specifically detect a given side reaction during CAM charge/discharge, allowing, e.g., to discriminate between lattice oxygen and dissolved TMs. Furthermore, it is shown via online electrochemical mass spectrometry (OEMS) that O2 reduction in the here-used LP47 electrolyte consumes ∼2.3 electrons/O2. Using this value, the lattice oxygen release deduced from the 3-electrode setup upon charging of the NCA WE is in good agreement with OEMS measurements up to NCA potentials >4.65 VLi. At higher potentials, the contributions from the reduction of TMII+ ions can be quantified by comparing the integrated SE current with the O2 evolution from OEMS.
- Open Access
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090514
Understanding the Effect of Lithium Nitrate as Additive in Carbonate-Based Electrolytes for Silicon Anodes
Due to its high specific capacity, silicon is one of the most promising anode materials for next-generation lithium-ion batteries. However, its large volumetric changes upon (de)lithiation of ∼300% lead to a rupture/re-formation of the solid-electrolyte interphase (SEI) upon cycling, resulting in continuous electrolyte consumption and irreversible loss of lithium. Therefore, it is crucial to use electrolyte systems that form a more stable SEI that can withstand large volume changes. Here, we investigate lithium nitrate (LiNO3) and lithium nitrite (LiNO2) as electrolyte additives. Linear scan voltammetry on carbon black working electrodes in a half-cell configuration with LiNO3-containing 1 M LiPF6 in EC/DEC (1/2 v/v) revealed a two-step reduction mechanism, whereby the first reduction peak could be attributed to the conversion of LiNO3 to LiNO2, while X-ray photoelectron spectroscopy on harvested electrodes suggests the formation of Li3N during the second reduction peak. On-line electrochemical mass spectrometry (OEMS) on carbon black electrodes showed that N2O gas is evolved upon the reduction of LiNO3- and LiNO2-containing electrolytes but that the gassing associated with EC reduction is significantly reduced. Furthermore, OEMS and voltammetry were used to examine the redox chemistry of LiNO2 additive. Finally, LiNO3 and LiNO2 additives significantly improved the cycle-life of Si||NCM622 full-cells.
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090514
Open AccessUnderstanding the Effect of Lithium Nitrate as Additive in Carbonate-Based Electrolytes for Silicon Anodes
Due to its high specific capacity, silicon is one of the most promising anode materials for next-generation lithium-ion batteries. However, its large volumetric changes upon (de)lithiation of ∼300% lead to a rupture/re-formation of the solid-electrolyte interphase (SEI) upon cycling, resulting in continuous electrolyte consumption and irreversible loss of lithium. Therefore, it is crucial to use electrolyte systems that form a more stable SEI that can withstand large volume changes. Here, we investigate lithium nitrate (LiNO3) and lithium nitrite (LiNO2) as electrolyte additives. Linear scan voltammetry on carbon black working electrodes in a half-cell configuration with LiNO3-containing 1 M LiPF6 in EC/DEC (1/2 v/v) revealed a two-step reduction mechanism, whereby the first reduction peak could be attributed to the conversion of LiNO3 to LiNO2, while X-ray photoelectron spectroscopy on harvested electrodes suggests the formation of Li3N during the second reduction peak. On-line electrochemical mass spectrometry (OEMS) on carbon black electrodes showed that N2O gas is evolved upon the reduction of LiNO3- and LiNO2-containing electrolytes but that the gassing associated with EC reduction is significantly reduced. Furthermore, OEMS and voltammetry were used to examine the redox chemistry of LiNO2 additive. Finally, LiNO3 and LiNO2 additives significantly improved the cycle-life of Si||NCM622 full-cells.
- Open Access
- 21 August 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090503
Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes
Microscale silicon particles have a higher specific capacity but larger volume expansion than graphite particles, leading to particle decoupling and lifetime limitations. This study investigates a wide range of external mechanical pressures from zero (ZP - 0.00 MPa) to high (HP - 0.50 MPa) pressure to determine the optimal pressure for high rate capability, cyclic lifetime, energy density, low temperature rise, and low cell thickness gain. The cells are characterized by rate tests and impedance spectroscopy, and are aged until 70% state of health (SoH). The post-mortem analysis after 70% SoH and thickness measurements over 360 cycles in a compression test bench offer insights into the thickness gain. Electrochemical results reveal an immediate reduction in discharge capacity upon transitioning from normal pressure (NP - 0.20 MPa) to ZP, with NP and HP exhibiting superior performance over aging. The impedance was reduced initially and over aging for higher mechanical pressures, especially the cathode contact resistance, resulting in lower temperature rises during the rate tests. Overall, applying higher pressures reduced the anode and cell thickness gain. Moreover, the porosity decreased with increasing pressure, as determined by mercury intrusion porosimetry and pycnometer measurements. The increase of the anode mass correlates to the total charge throughput, which is pressure-dependent and the highest for NP.
- 21 August 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090503
Open AccessEffect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes
Microscale silicon particles have a higher specific capacity but larger volume expansion than graphite particles, leading to particle decoupling and lifetime limitations. This study investigates a wide range of external mechanical pressures from zero (ZP - 0.00 MPa) to high (HP - 0.50 MPa) pressure to determine the optimal pressure for high rate capability, cyclic lifetime, energy density, low temperature rise, and low cell thickness gain. The cells are characterized by rate tests and impedance spectroscopy, and are aged until 70% state of health (SoH). The post-mortem analysis after 70% SoH and thickness measurements over 360 cycles in a compression test bench offer insights into the thickness gain. Electrochemical results reveal an immediate reduction in discharge capacity upon transitioning from normal pressure (NP - 0.20 MPa) to ZP, with NP and HP exhibiting superior performance over aging. The impedance was reduced initially and over aging for higher mechanical pressures, especially the cathode contact resistance, resulting in lower temperature rises during the rate tests. Overall, applying higher pressures reduced the anode and cell thickness gain. Moreover, the porosity decreased with increasing pressure, as determined by mercury intrusion porosimetry and pycnometer measurements. The increase of the anode mass correlates to the total charge throughput, which is pressure-dependent and the highest for NP.
- Open Access
- 3 June 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (6) , 060506
Depletion of Electrolyte Salt Upon Calendaric Aging of Lithium-Ion Batteries and its Effect on Cell Performance
The trend for increased nickel content in layered transition metal oxide cathode active materials and increasing charging cut-off voltages aggravates aging of lithium-ion battery cells at high state of charge (SOC). We investigate the calendaric aging behavior of large-format automotive prototype cells and laboratory single-layer pouch cells at high but realistic cell voltages/SOCs and demonstrate that electrolyte oxidation in combination with follow-up reactions can cause a significant loss of the LiPF6 salt in the electrolyte. For this, we analyze the LiPF6 concentration in aged cells, the generation of H2 upon storage, and the cell resistance for different aging conditions. We show that the LiPF6 loss is a critical aging phenomenon, as it cannot readily be detected by capacity fading measurements at low/medium C-rates or by cell resistance measurements, while it severely reduces rate and fast-charging capability. Under certain circumstances, LiPF6 loss can even lead to a temporary capacity increase due to conversion of the conducting salt in the electrolyte to cyclable lithium in the active material. Finally, we suggest a possible reaction mechanism and a simple accounting model to keep track of how different side reactions involved in LiPF6 loss change the cyclable lithium inventory of a lithium-ion cell.
- 3 June 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (6) , 060506
Open AccessDepletion of Electrolyte Salt Upon Calendaric Aging of Lithium-Ion Batteries and its Effect on Cell Performance
The trend for increased nickel content in layered transition metal oxide cathode active materials and increasing charging cut-off voltages aggravates aging of lithium-ion battery cells at high state of charge (SOC). We investigate the calendaric aging behavior of large-format automotive prototype cells and laboratory single-layer pouch cells at high but realistic cell voltages/SOCs and demonstrate that electrolyte oxidation in combination with follow-up reactions can cause a significant loss of the LiPF6 salt in the electrolyte. For this, we analyze the LiPF6 concentration in aged cells, the generation of H2 upon storage, and the cell resistance for different aging conditions. We show that the LiPF6 loss is a critical aging phenomenon, as it cannot readily be detected by capacity fading measurements at low/medium C-rates or by cell resistance measurements, while it severely reduces rate and fast-charging capability. Under certain circumstances, LiPF6 loss can even lead to a temporary capacity increase due to conversion of the conducting salt in the electrolyte to cyclable lithium in the active material. Finally, we suggest a possible reaction mechanism and a simple accounting model to keep track of how different side reactions involved in LiPF6 loss change the cyclable lithium inventory of a lithium-ion cell.