Mihai Costea
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mihai Costea has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Miruna Ciolca
Department of Strength of Materials, National University of Science and Technology POLITEHNICA Bucharest, Splaiul Independentei 313, 060042 Bucharest, Romania
5 shared publications - Florin Baciu
Department of Strength of Materials, National University of Science and Technology POLITEHNICA Bucharest, Splaiul Independentei 313, 060042 Bucharest, Romania
3 shared publications Bogdan‐Nicolae Stoian
Faculty of Industrial Engineering and Robotics Robots and Manufacturing Systems National University of Science and Technology POLITEHNICA Bucharest Bucharest Romania
2 shared publications- Constantin Stochioiu
Strength of Materials Department, Faculty of Industrial Engineering and Robotics, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania
2 shared publications - Gabriel Jiga
Faculty of Industrial Engineering and Robotics Strength of Materials Department National University of Science and Technology POLITEHNICA Bucharest Bucharest Romania
2 shared publications - Alexandru Paraschiv
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
1 shared publication
Latest Publications
- 13 August 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Influence of Wall Thickness on the Impact Behavior of 3D Printed Gyroid Lattices for Paragliding Protectors
This paper presents an experimental investigation on the impact performance of 3D‐printed gyroid lattice structures with varying wall thicknesses. The aim of this article is to evaluate the energy absorption capacity at impact and its potential application in paragliding safety equipment. The test specimens, designed as 60 mm cubes composed of eight 30 mm gyroid unit cells, are manufactured from TPU 95A using FDM technology. Five wall thicknesses, ranging from 0.6 to 1 mm, are tested. Impact experiments are performed on an INSTRON CEAST 9340 drop‐weight system, and the force–time dependence is analyzed to assess the structural response. The 0.9 mm configuration shows the best performance, combining low peak force with stable, progressive deformation and no material failure—key features for protective applications. These findings highlight the viability of gyroid‐based designs for energy‐absorbing structures and pave the way for further studies involving alternative lattice geometries, different material types, and comparisons with existing foam‐based protectors.
- 13 August 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Influence of Wall Thickness on the Impact Behavior of 3D Printed Gyroid Lattices for Paragliding Protectors
This paper presents an experimental investigation on the impact performance of 3D‐printed gyroid lattice structures with varying wall thicknesses. The aim of this article is to evaluate the energy absorption capacity at impact and its potential application in paragliding safety equipment. The test specimens, designed as 60 mm cubes composed of eight 30 mm gyroid unit cells, are manufactured from TPU 95A using FDM technology. Five wall thicknesses, ranging from 0.6 to 1 mm, are tested. Impact experiments are performed on an INSTRON CEAST 9340 drop‐weight system, and the force–time dependence is analyzed to assess the structural response. The 0.9 mm configuration shows the best performance, combining low peak force with stable, progressive deformation and no material failure—key features for protective applications. These findings highlight the viability of gyroid‐based designs for energy‐absorbing structures and pave the way for further studies involving alternative lattice geometries, different material types, and comparisons with existing foam‐based protectors.
- 6 August 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Finite Element Analysis of the Performance and Structural Behavior of Polymers Embedded in the Structure of an Exo‐Prosthesis
This study presents a numerical‐based methodology for the integration of polymer materials as key components of an upper limb Exo‐prosthesis. The approach focuses on the use of carbon fiber‐reinforced poly‐lactic acid (PLA+CF), fabricated using additive manufacturing, for the distal phalanges and metacarpal elements. Material integration is achieved through finite element method (FEA) simulations, enabling the evaluation of structural behavior under dynamic loading conditions and ensuring compatibility with biomechanical requirements. The work validates the entire numerical model, including structural performance and material behavior, providing a comprehensive evaluation of the Exo‐prosthesis design. The validation of the numerical model is highlighted using a dynamic analysis based on the finite element method (FEA). By examining the structural behavior under various external loads, the manufacturing method and the type of material used in the prosthesis construction are assessed. The structural analysis of the components constituting the designed system is crucial, as it aids in identifying regions subjected to significant stresses. Advanced FEA simulations are employed not only to validate the overall design but also to optimize the prototype when effective stresses impact the structural integrity of the device.
- 6 August 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Finite Element Analysis of the Performance and Structural Behavior of Polymers Embedded in the Structure of an Exo‐Prosthesis
This study presents a numerical‐based methodology for the integration of polymer materials as key components of an upper limb Exo‐prosthesis. The approach focuses on the use of carbon fiber‐reinforced poly‐lactic acid (PLA+CF), fabricated using additive manufacturing, for the distal phalanges and metacarpal elements. Material integration is achieved through finite element method (FEA) simulations, enabling the evaluation of structural behavior under dynamic loading conditions and ensuring compatibility with biomechanical requirements. The work validates the entire numerical model, including structural performance and material behavior, providing a comprehensive evaluation of the Exo‐prosthesis design. The validation of the numerical model is highlighted using a dynamic analysis based on the finite element method (FEA). By examining the structural behavior under various external loads, the manufacturing method and the type of material used in the prosthesis construction are assessed. The structural analysis of the components constituting the designed system is crucial, as it aids in identifying regions subjected to significant stresses. Advanced FEA simulations are employed not only to validate the overall design but also to optimize the prototype when effective stresses impact the structural integrity of the device.
- Open Access
- 5 August 2026
- Published by MDPI AG in Technologies
- Vol. 14 (8) , 492
High-Temperature Tensile Behavior of Wrought and SLM-Fabricated Inconel 718: Effects of Build Orientation and Finite Element Modeling
Additive manufacturing enables the production of geometrically complex nickel-based superalloy components, but the high-temperature tensile response of selective laser-melted Inconel 718 remains strongly dependent on manufacturing route and build orientation. In this study, the tensile behavior of Inconel 718 specimens machined from wrought bar stock and fabricated by selective laser melting in horizontal and vertical build orientations was investigated at 23 °C, 450 °C, 550 °C and 750 °C. The experimental values were used in a finite element simulation to create a model that can accurately predict the mechanical behavior of IN718. The results show that the X-oriented SLM specimens exhibit tensile properties comparable to those of the wrought material, whereas the Z-oriented specimens display reduced strength and increased scatter, highlighting the effect of build orientation on mechanical performance. The numerical simulations reproduced the experimental stress–strain response with good agreement within the elastic and plastic deformation regimes, demonstrating the suitability of the proposed modeling approach for high-temperature structural assessment of Inconel 718 components manufactured by conventional and additive technologies.
- 5 August 2026
- Published by MDPI AG in Technologies
- Vol. 14 (8) , 492
Open AccessHigh-Temperature Tensile Behavior of Wrought and SLM-Fabricated Inconel 718: Effects of Build Orientation and Finite Element Modeling
Additive manufacturing enables the production of geometrically complex nickel-based superalloy components, but the high-temperature tensile response of selective laser-melted Inconel 718 remains strongly dependent on manufacturing route and build orientation. In this study, the tensile behavior of Inconel 718 specimens machined from wrought bar stock and fabricated by selective laser melting in horizontal and vertical build orientations was investigated at 23 °C, 450 °C, 550 °C and 750 °C. The experimental values were used in a finite element simulation to create a model that can accurately predict the mechanical behavior of IN718. The results show that the X-oriented SLM specimens exhibit tensile properties comparable to those of the wrought material, whereas the Z-oriented specimens display reduced strength and increased scatter, highlighting the effect of build orientation on mechanical performance. The numerical simulations reproduced the experimental stress–strain response with good agreement within the elastic and plastic deformation regimes, demonstrating the suitability of the proposed modeling approach for high-temperature structural assessment of Inconel 718 components manufactured by conventional and additive technologies.
- 10 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4) , e70418
Influence of 3D Printing Parameters on Mechanical and Elastic Characteristics
This study investigates how two key 3D printing parameters—infill density and layer orientation—affect the mechanical behavior of PLA specimens produced using Fused Deposition Modeling (FDM) under tensile loading. Standardized tensile samples were designed per ISO 6892‐1 in CATIA V5 and printed using Crealty software, with infill density set at 30%, 60%, and 90%, and layer orientation varied in three directions (A, B, and C). All other printing settings, including extrusion temperature, speed, and linear infill pattern, were kept constant to isolate these variables. Mechanical performance was evaluated through Digital Image Correlation (DIC), a precise optical method for measuring strain and deformation. Results showed that higher infill density increased stiffness and tensile strength, while the layer orientation had a significant impact on failure behavior. Specimens printed in C orientation, where filament layers aligned with the tensile direction, demonstrated superior strength and uniform stress distribution. Conversely, A orientation samples failed prematurely due to delamination and crack initiation at interlayer boundaries. Overall, the study highlights that optimizing infill density and layer orientation is essential for enhancing the structural integrity and functional performance of FDM‐printed PLA components.
- 10 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4) , e70418
Influence of 3D Printing Parameters on Mechanical and Elastic Characteristics
This study investigates how two key 3D printing parameters—infill density and layer orientation—affect the mechanical behavior of PLA specimens produced using Fused Deposition Modeling (FDM) under tensile loading. Standardized tensile samples were designed per ISO 6892‐1 in CATIA V5 and printed using Crealty software, with infill density set at 30%, 60%, and 90%, and layer orientation varied in three directions (A, B, and C). All other printing settings, including extrusion temperature, speed, and linear infill pattern, were kept constant to isolate these variables. Mechanical performance was evaluated through Digital Image Correlation (DIC), a precise optical method for measuring strain and deformation. Results showed that higher infill density increased stiffness and tensile strength, while the layer orientation had a significant impact on failure behavior. Specimens printed in C orientation, where filament layers aligned with the tensile direction, demonstrated superior strength and uniform stress distribution. Conversely, A orientation samples failed prematurely due to delamination and crack initiation at interlayer boundaries. Overall, the study highlights that optimizing infill density and layer orientation is essential for enhancing the structural integrity and functional performance of FDM‐printed PLA components.
- 5 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Determination of Mechanical Behavior of 3D Printed as‐Built Samples of Co–Cr Alloy
This study investigates the mechanical behavior of additively manufactured cobalt–chromium (Co–Cr) alloy samples produced by powder bed fusion (PBF) in the as‐built condition. The material was characterized through density, hardness, and uniaxial compression testing to establish correlations among these properties and evaluate its suitability for aerospace components subjected to compressive loading. The Co–Cr specimens exhibited high density (∼8333 kg/m 3 ) with minimal variation, and an average Vickers hardness of 368 HV30, indicating good material uniformity. Compression tests yielded an average 0.05% offset yield strength of 669 MPa, ultimate compressive strength of 856 MPa, elastic modulus of 212 GPa, and Poisson's ratio of 0.343. These results confirm the mechanical performance of PBF Co–Cr alloys and align closely with values reported in the literature. The experimental data were further applied in a modal analysis of a turbine stator blade to determine its eigenfrequencies and vibration modes. The modal results indicate good stiffness, supporting the alloy's potential for use in complex, load‐bearing aerospace components. This work provides a foundation for future high‐temperature investigations and comparative studies with alternative materials such as Inconel 718.
- 5 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Determination of Mechanical Behavior of 3D Printed as‐Built Samples of Co–Cr Alloy
This study investigates the mechanical behavior of additively manufactured cobalt–chromium (Co–Cr) alloy samples produced by powder bed fusion (PBF) in the as‐built condition. The material was characterized through density, hardness, and uniaxial compression testing to establish correlations among these properties and evaluate its suitability for aerospace components subjected to compressive loading. The Co–Cr specimens exhibited high density (∼8333 kg/m 3 ) with minimal variation, and an average Vickers hardness of 368 HV30, indicating good material uniformity. Compression tests yielded an average 0.05% offset yield strength of 669 MPa, ultimate compressive strength of 856 MPa, elastic modulus of 212 GPa, and Poisson's ratio of 0.343. These results confirm the mechanical performance of PBF Co–Cr alloys and align closely with values reported in the literature. The experimental data were further applied in a modal analysis of a turbine stator blade to determine its eigenfrequencies and vibration modes. The modal results indicate good stiffness, supporting the alloy's potential for use in complex, load‐bearing aerospace components. This work provides a foundation for future high‐temperature investigations and comparative studies with alternative materials such as Inconel 718.
- Open Access
- 2 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Experimental Comparison of Impact Behavior in Thin Carbon Fiber Reinforced and 3d Printed Polymeric Plates
This study presents a comparative investigation of the low‐velocity impact behavior of thin plates made from carbon fiber reinforced polymer (CFRP), polylactic acid (PLA), and acrylonitrile butadiene styrene (ABS). Plates with nominal thicknesses of 0.5 and 5 mm were subjected to standardized drop‐weight impact tests to evaluate their energy absorption capacity, failure modes, and structural response under dynamic loading. The experimental results indicate significant differences between the three materials: CFRP plates demonstrated superior impact resistance and energy absorption efficiency, attributed to their layered fiber structure and brittle failure behavior, while PLA specimens exhibited earlier failure through plastic deformation and crack propagation. The ABS specimens did not exhibit any visible cracks at an impact energy of 2 J, indicating a high capacity for plastic deformation without the immediate occurrence of cracking or fracture. To investigate the failure threshold of the material, the tests were repeated at an increased kinetic energy of 8 J. This step aimed to determine the failure mode and the upper energy absorption limit of the ABS material under intensified dynamic loading. The absorbed impact energy per unit thickness was analyzed to isolate and highlight the intrinsic material behavior, minimizing the influence of thickness variation. Finite element analysis models were developed to simulate the impact response of the tested specimens. The study provides valuable insights for material selection in the design of lightweight structures exposed to low‐velocity impact, with potential applications in aerospace, automotive, and consumer electronics industries.
- 2 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Open AccessExperimental Comparison of Impact Behavior in Thin Carbon Fiber Reinforced and 3d Printed Polymeric Plates
This study presents a comparative investigation of the low‐velocity impact behavior of thin plates made from carbon fiber reinforced polymer (CFRP), polylactic acid (PLA), and acrylonitrile butadiene styrene (ABS). Plates with nominal thicknesses of 0.5 and 5 mm were subjected to standardized drop‐weight impact tests to evaluate their energy absorption capacity, failure modes, and structural response under dynamic loading. The experimental results indicate significant differences between the three materials: CFRP plates demonstrated superior impact resistance and energy absorption efficiency, attributed to their layered fiber structure and brittle failure behavior, while PLA specimens exhibited earlier failure through plastic deformation and crack propagation. The ABS specimens did not exhibit any visible cracks at an impact energy of 2 J, indicating a high capacity for plastic deformation without the immediate occurrence of cracking or fracture. To investigate the failure threshold of the material, the tests were repeated at an increased kinetic energy of 8 J. This step aimed to determine the failure mode and the upper energy absorption limit of the ABS material under intensified dynamic loading. The absorbed impact energy per unit thickness was analyzed to isolate and highlight the intrinsic material behavior, minimizing the influence of thickness variation. Finite element analysis models were developed to simulate the impact response of the tested specimens. The study provides valuable insights for material selection in the design of lightweight structures exposed to low‐velocity impact, with potential applications in aerospace, automotive, and consumer electronics industries.
- Open Access
- 2 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
The Influence of Infill Density on the Impact Behavior of 3D‐Printed PLA Parts
The study focuses on the experimental determination of the impact behavior of PLA components manufactured through additive manufacturing, where the infill density of each tested specimen is varied. The evaluation of the impact energy absorbed by each configuration provides relevant insights into the influence of internal structure on mechanical performance, thus contributing to the optimization of manufacturing parameters for the development of components that must respect the efficiency in terms of mechanical strength and material use. In this paper, the authors investigate the influence of internal structure on impact strength by proposing four different infill density configurations for 3D‐printed PLA specimens: 30%, 50%, 80%, and 100% infill. These variations were selected to provide a comprehensive understanding of how internal material volume increase affects the mechanical performances under impact loading. By systematically analyzing the absorbed impact energy for each configuration, the study aims to establish correlations between infill percentage and structural integrity, offering valuable insights for optimizing additive manufacturing parameters.
- 2 July 2026
- Published by Wiley in Macromolecular Symposia
- Vol. 415 (4)
Open AccessThe Influence of Infill Density on the Impact Behavior of 3D‐Printed PLA Parts
The study focuses on the experimental determination of the impact behavior of PLA components manufactured through additive manufacturing, where the infill density of each tested specimen is varied. The evaluation of the impact energy absorbed by each configuration provides relevant insights into the influence of internal structure on mechanical performance, thus contributing to the optimization of manufacturing parameters for the development of components that must respect the efficiency in terms of mechanical strength and material use. In this paper, the authors investigate the influence of internal structure on impact strength by proposing four different infill density configurations for 3D‐printed PLA specimens: 30%, 50%, 80%, and 100% infill. These variations were selected to provide a comprehensive understanding of how internal material volume increase affects the mechanical performances under impact loading. By systematically analyzing the absorbed impact energy for each configuration, the study aims to establish correlations between infill percentage and structural integrity, offering valuable insights for optimizing additive manufacturing parameters.
- 16 October 2023
- Published by Wiley in Macromolecular Symposia
- Vol. 411 (1)
Comparative Studies between Two Plastic Materials Used in 3D Printing
This paper deals with the analysis and comparative studies of the two of the most used types of polymer filaments dedicated to the 3D printing industry. The study is focused on the mechanical, elastic, and thermal properties of two different types of plastic materials filaments – acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) as well as on future development in various categories like industrial, medical, home decoration, and education. For carrying out this study, different specimens are printed using fused filament fabrication (FFF) technique, taking into account an infill percentage of 30% with a triangular shape as pattern type (internal structure).
- 16 October 2023
- Published by Wiley in Macromolecular Symposia
- Vol. 411 (1)
Comparative Studies between Two Plastic Materials Used in 3D Printing
This paper deals with the analysis and comparative studies of the two of the most used types of polymer filaments dedicated to the 3D printing industry. The study is focused on the mechanical, elastic, and thermal properties of two different types of plastic materials filaments – acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) as well as on future development in various categories like industrial, medical, home decoration, and education. For carrying out this study, different specimens are printed using fused filament fabrication (FFF) technique, taking into account an infill percentage of 30% with a triangular shape as pattern type (internal structure).