Devabrata Mishra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Devabrata Mishra has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Akshay Kumar
Metal Extraction and Recycling Division, National Metallurgical Laboratory, Jamshedpur, India
2 shared publicationsAnkita Dash
Metal Extraction and Recycling Division, National Metallurgical Laboratory, Jamshedpur, India
1 shared publication- Ashutosh Panchal
Defence Metallurgical Research Laboratory, Hyderabad, India
1 shared publication - Ch.R.V.S. Nagesh
DRDO-Defence Metallurgical Research Laboratory (DMRL), Kanchanbagh PO, Hyderabad - 500 058, India
1 shared publication K. K. Sahu
Metal Extraction and Recycling Division, National Metallurgical Laboratory, Jamshedpur, India
1 shared publication- K. K. Sahu
CSIR-National Metallurgical Laboratory, Jamshedpur - 831 007, India
1 shared publication
Latest Publications
- 11 February 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 43 (2) , 1401-1423
Prospects of Vanadium Extraction from Different Secondary Sources: A Review
- 11 February 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 43 (2) , 1401-1423
Prospects of Vanadium Extraction from Different Secondary Sources: A Review
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 61 (3) , 333-344
Extraction of vanadium from pet-coke gasification cinder - Part 1: Leaching kinetics studies in sulphuric acid medium
PPetcoke cinder is a solid by-product generated during the gasification of petcoke, accounting for three to five percent of the petroleum coke mass. It commonly contains valuable metals such as V, Ni, Al, and Fe, highlighting its potential as a resource for vanadium extraction. Therefore, it may be considered an emerging secondary source of vanadium and other critical metals. The conventional pyro-cum-hydrometallurgical process for vanadium recovery relies on alkali roasting, which is not only energy-intensive but also contributes to greenhouse gas emissions. Given environmental concerns and high energy consumption, this study presents a state-of-the-art, economically feasible, and energy-efficient process for extracting V from petcoke cinders. This paper discusses the acid-leaching method for vanadium extraction from petcoke cinders and examines various parameters, including acid concentration, temperature, process duration, percentage of H2O2, amount of sodium dodecyl sulfate (SDS), and solid-liquid phase ratios. The optimal recovery rate of V, 95.62%, was achieved under the following conditions: 4 M sulfuric acid at 90 °C for three hours, with a solid-liquid ratio of 15%, H2O2 at 20%, and SDS at 6%. Leaching kinetics were investigated using a shrinking surface-controlled model, revealing a reaction order of 1.29 with respect to sulfuric acid concentration. According to the Arrhenius equation, the apparent activation energy of leaching was approximately 27.67 kJ/mol, and the empirical equation representing the acid leaching kinetics of vanadium was established as 1-(1-α) 1/3=kt=(9.261×103 )[H2SO4 ]1.2916exp[-27674/RT]T.
- 1 January 2025
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 61 (3) , 333-344
Open AccessExtraction of vanadium from pet-coke gasification cinder - Part 1: Leaching kinetics studies in sulphuric acid medium
PPetcoke cinder is a solid by-product generated during the gasification of petcoke, accounting for three to five percent of the petroleum coke mass. It commonly contains valuable metals such as V, Ni, Al, and Fe, highlighting its potential as a resource for vanadium extraction. Therefore, it may be considered an emerging secondary source of vanadium and other critical metals. The conventional pyro-cum-hydrometallurgical process for vanadium recovery relies on alkali roasting, which is not only energy-intensive but also contributes to greenhouse gas emissions. Given environmental concerns and high energy consumption, this study presents a state-of-the-art, economically feasible, and energy-efficient process for extracting V from petcoke cinders. This paper discusses the acid-leaching method for vanadium extraction from petcoke cinders and examines various parameters, including acid concentration, temperature, process duration, percentage of H2O2, amount of sodium dodecyl sulfate (SDS), and solid-liquid phase ratios. The optimal recovery rate of V, 95.62%, was achieved under the following conditions: 4 M sulfuric acid at 90 °C for three hours, with a solid-liquid ratio of 15%, H2O2 at 20%, and SDS at 6%. Leaching kinetics were investigated using a shrinking surface-controlled model, revealing a reaction order of 1.29 with respect to sulfuric acid concentration. According to the Arrhenius equation, the apparent activation energy of leaching was approximately 27.67 kJ/mol, and the empirical equation representing the acid leaching kinetics of vanadium was established as 1-(1-α) 1/3=kt=(9.261×103 )[H2SO4 ]1.2916exp[-27674/RT]T.
- Open Access
- 9 March 2023
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 73 (No 2) , 241-251
Microstructure and Mechanical Properties of Tungsten Heavy Alloy Prepared Using Tungsten Metal Powder Produced from Heavy Alloy Scrap
Tungsten metal powder, using a hydrometallurgical route, was extracted from tungsten heavy alloy scrap that was generated during machining of penetrator cores for the manufacture of Fin Stabilised Armour Piercing Discarding Sabot (FSAPDS). The powder was subjected to extensive characterisation that included physical property evaluation and analysis of the alloy chemistry in order to assess its suitability for the preparation of tungsten heavy alloys with enhanced mechanical properties. Subsequently, a tungsten heavy alloy based on W-Ni-Co was consolidated using this powder through liquid phase sintering followed by heat treatment and swaging operations to realize long rods (~500 mm). This was followed by a detailed characterisation that included microstructure and mechanical property. The mechanical properties of these rods are promising, exhibiting a good balance of tensile and impact properties, which in turn underscores the potential of these recycled powders in the production of premium quality heavy alloy long rods for stringent applications such as kinetic energy penetrators.
- 9 March 2023
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 73 (No 2) , 241-251
Open AccessMicrostructure and Mechanical Properties of Tungsten Heavy Alloy Prepared Using Tungsten Metal Powder Produced from Heavy Alloy Scrap
Tungsten metal powder, using a hydrometallurgical route, was extracted from tungsten heavy alloy scrap that was generated during machining of penetrator cores for the manufacture of Fin Stabilised Armour Piercing Discarding Sabot (FSAPDS). The powder was subjected to extensive characterisation that included physical property evaluation and analysis of the alloy chemistry in order to assess its suitability for the preparation of tungsten heavy alloys with enhanced mechanical properties. Subsequently, a tungsten heavy alloy based on W-Ni-Co was consolidated using this powder through liquid phase sintering followed by heat treatment and swaging operations to realize long rods (~500 mm). This was followed by a detailed characterisation that included microstructure and mechanical property. The mechanical properties of these rods are promising, exhibiting a good balance of tensile and impact properties, which in turn underscores the potential of these recycled powders in the production of premium quality heavy alloy long rods for stringent applications such as kinetic energy penetrators.