Yihao Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yihao Yang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Binhao Wang
State Key Laboratory of Ultrafast Optical Science and Technology, Xi'an Institute of Optics and Precision Mechanics Chinese Academy of Sciences Xi'an Shaanxi China
2 shared publications Baiyu Liu
Universiy of Chinese Academy of Sciences 1 , Beijing, China
1 shared publicationBo Wang
Key Laboratory of Ultra-fast Photoelectric Diagnostics Technology, Xi’an Institute of Optics and Precision Mechanics of CAS 2 , Xi’an, China
1 shared publication- Chao Cheng
State Key Laboratory of Ultrafast Optical Science and Technology, Xi’an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi’an 710119, China
1 shared publication - Dan Li
Faculty of Electronic and Information Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Houyou Lai
State Key Laboratory of Ultrafast Optical Science and Technology, Xi’an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi’an 710119, China
1 shared publication
Latest Publications
- Open Access
- 17 December 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1416
A Low-Noise Hybrid-Integrated Balanced Homodyne Receiver with 2.5 GHz Bandwidth and 15 dB Quantum Shot Noise Clearance
The rapid development of continuous-variable quantum communication has driven an increasing demand for high-performance quantum signal processing modules. Among these, the balanced homodyne detector (BHD) has emerged as a leading solution for practical quantum state measurement due to its capability to provide complete quantum mechanical characterization. However, its performance is often constrained by limited bandwidth and high noise levels, primarily due to the reliance on bulk optical components and discrete receiver electronics. The dominant noise source in these systems typically stems from electronic noise, while imbalances in the optical path further degrade the signal-to-noise ratio (SNR) of the BHD. In this work, we present an adjustable integrated optical path to enhance the balance within the BHD system, along with a low-noise transimpedance amplifier (TIA) by employing optoelectronic co-design. Our design achieves a bandwidth of 2.5 GHz, an input-referred noise current of only 2 pA/√Hz in 180 nm CMOS technology, and a measured quantum shot noise clearance of 15 dB generated from a 700 μA photocurrent. This is the maximum quantum shot noise clearance at the same BHD photocurrent reported to date above the GHz bandwidth.
- 17 December 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1416
Open AccessA Low-Noise Hybrid-Integrated Balanced Homodyne Receiver with 2.5 GHz Bandwidth and 15 dB Quantum Shot Noise Clearance
The rapid development of continuous-variable quantum communication has driven an increasing demand for high-performance quantum signal processing modules. Among these, the balanced homodyne detector (BHD) has emerged as a leading solution for practical quantum state measurement due to its capability to provide complete quantum mechanical characterization. However, its performance is often constrained by limited bandwidth and high noise levels, primarily due to the reliance on bulk optical components and discrete receiver electronics. The dominant noise source in these systems typically stems from electronic noise, while imbalances in the optical path further degrade the signal-to-noise ratio (SNR) of the BHD. In this work, we present an adjustable integrated optical path to enhance the balance within the BHD system, along with a low-noise transimpedance amplifier (TIA) by employing optoelectronic co-design. Our design achieves a bandwidth of 2.5 GHz, an input-referred noise current of only 2 pA/√Hz in 180 nm CMOS technology, and a measured quantum shot noise clearance of 15 dB generated from a 700 μA photocurrent. This is the maximum quantum shot noise clearance at the same BHD photocurrent reported to date above the GHz bandwidth.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 189-192
A 2 pA/√Hz Input-Referred Noise TIA in 180-nm CMOS With 2.5 GHz Bandwidth for Optical Receiver
This letter describes an ultra-low-noise, high-speed transimpedance amplifier (TIA) applied to the analog front-end (AFE) circuit of the high-sensitivity optical receiver. A combination of a three-stage amplifier and two positive feedback Miller capacitors is introduced to comprehensively reduce the input-referred noise current (IRNC) of a shunt-feedback TIA (SFTIA) and to extend its bandwidth. The proposed SFTIA utilizes an 80 KΩ resistor as the feedback resistor (RF) and achieves a bandwidth of 2.5 GHz and an average IRNC of only 2 pA/Hz in 180 nm CMOS technology, which is the lowest TIA noise reported to date above the GHz bandwidth. Although the fabrication process is not as advanced as the state-of-the-art process, we believe it remains valuable and instructive for a wide variety of applications requiring low noise and high sensitivity.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 189-192
A 2 pA/√Hz Input-Referred Noise TIA in 180-nm CMOS With 2.5 GHz Bandwidth for Optical Receiver
This letter describes an ultra-low-noise, high-speed transimpedance amplifier (TIA) applied to the analog front-end (AFE) circuit of the high-sensitivity optical receiver. A combination of a three-stage amplifier and two positive feedback Miller capacitors is introduced to comprehensively reduce the input-referred noise current (IRNC) of a shunt-feedback TIA (SFTIA) and to extend its bandwidth. The proposed SFTIA utilizes an 80 KΩ resistor as the feedback resistor (RF) and achieves a bandwidth of 2.5 GHz and an average IRNC of only 2 pA/Hz in 180 nm CMOS technology, which is the lowest TIA noise reported to date above the GHz bandwidth. Although the fabrication process is not as advanced as the state-of-the-art process, we believe it remains valuable and instructive for a wide variety of applications requiring low noise and high sensitivity.
- Open Access
- 1 October 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (10)
Design of multi-frequency point, high-isolation switches for micro-channel plate data acquisition
In order to replace the phosphor screen of a proximity-gated x-ray framing camera with a readout circuit using a time-interleaved structure, this paper carries out the design of a high-isolation RF switch. In this paper, a Metal-Oxide-Semiconductor Field Effect Tube (MOSFET) switching circuit is designed to achieve high isolation and low insertion loss at 0.5–3 GHz. This solves the problem that the switching circuit cannot be turned off properly due to the parasitic capacitance of MOSFETs in the process of RF signal transmission, resulting in signal feedthrough. It also ensures that the input signal can be transmitted to the output intact when the switching circuit is turned on. High isolation is achieved by using parallel resonance to increase the voltage division and series resonance to leak the current. The switch achieves 76 dB isolation and 0.07 dB insertion loss at 1 GHz frequency. Isolation is increased by adding parallel branches near the 2 and 3 GHz frequency points, achieving greater than 33 dB isolation from 0.5 to 3 GHz.
- 1 October 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (10)
Open AccessDesign of multi-frequency point, high-isolation switches for micro-channel plate data acquisition
In order to replace the phosphor screen of a proximity-gated x-ray framing camera with a readout circuit using a time-interleaved structure, this paper carries out the design of a high-isolation RF switch. In this paper, a Metal-Oxide-Semiconductor Field Effect Tube (MOSFET) switching circuit is designed to achieve high isolation and low insertion loss at 0.5–3 GHz. This solves the problem that the switching circuit cannot be turned off properly due to the parasitic capacitance of MOSFETs in the process of RF signal transmission, resulting in signal feedthrough. It also ensures that the input signal can be transmitted to the output intact when the switching circuit is turned on. High isolation is achieved by using parallel resonance to increase the voltage division and series resonance to leak the current. The switch achieves 76 dB isolation and 0.07 dB insertion loss at 1 GHz frequency. Isolation is increased by adding parallel branches near the 2 and 3 GHz frequency points, achieving greater than 33 dB isolation from 0.5 to 3 GHz.