Dharmendar Boolchandani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dharmendar Boolchandani has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Riyaz Ahmad
Department of Electronics and Communication Engineering, Malaviya National Institute of Technology, Jaipur, India
9 shared publications - Archana Singhal
Department of Electronics and Communication Engineering, Malaviya National Institute of Technology, Jaipur, India
7 shared publications - Dheeraj Singh Rajput
Department of Electronics and Communication Engineering, Malaviya National Institute of Technology, Jaipur, India
7 shared publications - Bharat Choudhary
Department of Electronics and Communication Engineering, Malaviya National Institute of Technology, Jaipur, India
5 shared publications - Amit Mahesh Joshi
Malaviya National Institute of Technology Jaipur
4 shared publications - Jyoti Sharma
Electronics and Communication Engineering Department, Birla Institute of Technology, Mesra, Jaipur, India
4 shared publications
Latest Publications
- 2 September 2026
- Published by Springer Nature
- p. 245-254
Power-Efficient and High-Speed Dynamic MCML XOR Gate Using Triple-Tail Cells Architecture
- 2 September 2026
- Published by Springer Nature
- p. 245-254
Power-Efficient and High-Speed Dynamic MCML XOR Gate Using Triple-Tail Cells Architecture
- 4 February 2026
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (8) , 1-32
Improved Race-Free Cascaded Dynamic PFSCL Technique for Multistage Applications
- 4 February 2026
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (8) , 1-32
Improved Race-Free Cascaded Dynamic PFSCL Technique for Multistage Applications
- 13 January 2026
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (2) , 32
Optimization of novel DPTL-PFD design for fast-settling PLL frequency synthesizer using Taguchi–ANOVA
- 13 January 2026
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (2) , 32
Optimization of novel DPTL-PFD design for fast-settling PLL frequency synthesizer using Taguchi–ANOVA
- 8 December 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (1) , 20
Design and optimization of a Quad-Tail-Cell dynamic MCML for low-power three-input logic using Taguchi and ANOVA methods
- 8 December 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (1) , 20
Design and optimization of a Quad-Tail-Cell dynamic MCML for low-power three-input logic using Taguchi and ANOVA methods
- 15 November 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (1) , 6
An efficient race-free dynamic MCML design for multistage applications
- 15 November 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 126 (1) , 6
An efficient race-free dynamic MCML design for multistage applications
- Open Access
- 13 May 2025
- Published by Japan Bilingual Publishing Co. in New Environmentally-Friendly Materials
- Vol. 4 (1) , 57-66
A Novel Approach to Fabricate a Polyamide-Copper TENG in Vertical Contact-Separation Mode
In this study, a novel design concept for a contact-separation Triboelectric Nanogenerator (TENG) utilizing polyimide (PI) film and copper (Cu) tape is presented. The innovation lies in enhancing the surface area and roughness of the PI film using 1000-grit sandpaper, which is manually rubbed over the film. This surface treatment significantly improves charge transfer between the PI and Cu layers, thereby enhancing the electrical performance of the TENG. The modified (rubbed) PI-Cu TENG achieved an open-circuit voltage (Voc) of 25 V and a short-circuit current (Isc) of 0.7 µA. Compared to a pristine (untreated) PI film, the hand-rubbed PI-Cu TENG demonstrated an increase in performance. Voc and Isc were improved by 78.6% and 75%, respectively, due to the increased surface roughness and area, which facilitated more efficient charge transfer at the interface. Additionally, the instantaneous power density showed a notable increase of 68.18% relative to the pristine film. The prototype device was characterized using a two-probe I-V measurement system to obtain Isc and Voc responses. Morphological changes in the rubbed PI film were confirmed via Scanning Electron Microscopy (SEM), performed using an FEI Nova Nano FESEM 450, revealing the presence of scratch-induced torsional layers. Surface roughness and topographical features were further analyzed using Bruker Multimode-8 Atomic Force Microscopy (AFM).
- 13 May 2025
- Published by Japan Bilingual Publishing Co. in New Environmentally-Friendly Materials
- Vol. 4 (1) , 57-66
Open AccessA Novel Approach to Fabricate a Polyamide-Copper TENG in Vertical Contact-Separation Mode
In this study, a novel design concept for a contact-separation Triboelectric Nanogenerator (TENG) utilizing polyimide (PI) film and copper (Cu) tape is presented. The innovation lies in enhancing the surface area and roughness of the PI film using 1000-grit sandpaper, which is manually rubbed over the film. This surface treatment significantly improves charge transfer between the PI and Cu layers, thereby enhancing the electrical performance of the TENG. The modified (rubbed) PI-Cu TENG achieved an open-circuit voltage (Voc) of 25 V and a short-circuit current (Isc) of 0.7 µA. Compared to a pristine (untreated) PI film, the hand-rubbed PI-Cu TENG demonstrated an increase in performance. Voc and Isc were improved by 78.6% and 75%, respectively, due to the increased surface roughness and area, which facilitated more efficient charge transfer at the interface. Additionally, the instantaneous power density showed a notable increase of 68.18% relative to the pristine film. The prototype device was characterized using a two-probe I-V measurement system to obtain Isc and Voc responses. Morphological changes in the rubbed PI film were confirmed via Scanning Electron Microscopy (SEM), performed using an FEI Nova Nano FESEM 450, revealing the presence of scratch-induced torsional layers. Surface roughness and topographical features were further analyzed using Bruker Multimode-8 Atomic Force Microscopy (AFM).
- 19 October 2024
- Published by Springer Nature
- p. 25-36
A 0.1–4.71 GHz Integer-N CP-PLL-Based Low-Power Frequency Synthesizer for High-Speed Applications
- 19 October 2024
- Published by Springer Nature
- p. 25-36
A 0.1–4.71 GHz Integer-N CP-PLL-Based Low-Power Frequency Synthesizer for High-Speed Applications
- 19 September 2024
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (2) , 749-771
A Novel 571.78 MHz–11.07 GHz Tuning Range Differential Ring Oscillator Application in a PLL Frequency Synthesizer with 895 ns Lock Time
- 19 September 2024
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (2) , 749-771
A Novel 571.78 MHz–11.07 GHz Tuning Range Differential Ring Oscillator Application in a PLL Frequency Synthesizer with 895 ns Lock Time