Hang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hang Liu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Joachim Albrecht
Research Institute for Innovative Surfaces FINO Aalen University Beethovenstr. 1 D‐73430 Aalen Germany
4 shared publications Katharina Weber
Aalen University Research Institute for Innovative Surfaces FINO Beethovenstr. 1 73430 Aalen Germany
3 shared publications- Michael Nase
Institute of Circular Economy of Bio:polymers (ibp) at Hof University of Applied Sciences, Alfons-Goppel- Platz 1, 95028 Hof, Germany
3 shared publications Michaela Zagler
Hof University of Applied Sciences Institute for Biopolymers and Sustainability ibp Alfons-Goppel-Platz 1 95028 Hof Germany
3 shared publications- Jochen Hofmann
Polymer Technology, Aalen University, Beethovenstr. 1, D-73430 Aalen, Germany
1 shared publication - Katharina Weber
Research Institute for Innovative Surfaces FINO, Aalen University, Beethovenstraße 1, 73430 Aalen, Germany
1 shared publication
Latest Publications
- Open Access
Near-Surface Reconfiguration of Biopolymer Blends by Mechanical Embossment: Creation of Friction-Reduced Foils
Biopolymer blends of polylactic acid (PLA) and polybutylene adipate-co-terephthalate (PBAT) are extruded into flexible monolayer films. These blends are excellent candidates for the realization of environmentally friendly packaging applications. A necessary pre-requisite for that are appropriate tribological properties under mechanical contact. Reasonable wear resistance allows good protection of packed goods, and low friction forces reduce difficulties in stacking. In this research, mechanical embossment under high loads at room temperature was used for the modification of polymer surfaces to exhibit a significant friction reduction under dry conditions. The results particularly show a systematic decrease in the coefficient of friction for biopolymer blends containing 30 wt% and 40 wt% PBAT. FTIR was used to analyze the change in surface composition after mechanical embossing. A sophisticated FTIR calibration method revealed that the blend with 30 wt% PBAT shows a modified distribution of PBAT and PLA at the surface due to mechanical embossment. This leads to a controlled and long-lasting modification of the surface properties without a substantial change in the chemical composition of the polymer in bulk. Without the use of additional coatings, biodegradable packaging foils with improved characteristics are accessible.
Open AccessNear-Surface Reconfiguration of Biopolymer Blends by Mechanical Embossment: Creation of Friction-Reduced Foils
Biopolymer blends of polylactic acid (PLA) and polybutylene adipate-co-terephthalate (PBAT) are extruded into flexible monolayer films. These blends are excellent candidates for the realization of environmentally friendly packaging applications. A necessary pre-requisite for that are appropriate tribological properties under mechanical contact. Reasonable wear resistance allows good protection of packed goods, and low friction forces reduce difficulties in stacking. In this research, mechanical embossment under high loads at room temperature was used for the modification of polymer surfaces to exhibit a significant friction reduction under dry conditions. The results particularly show a systematic decrease in the coefficient of friction for biopolymer blends containing 30 wt% and 40 wt% PBAT. FTIR was used to analyze the change in surface composition after mechanical embossing. A sophisticated FTIR calibration method revealed that the blend with 30 wt% PBAT shows a modified distribution of PBAT and PLA at the surface due to mechanical embossment. This leads to a controlled and long-lasting modification of the surface properties without a substantial change in the chemical composition of the polymer in bulk. Without the use of additional coatings, biodegradable packaging foils with improved characteristics are accessible.
- 17 October 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20)
Front Cover: Creating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting (ChemPhysChem 20/2023)
- 17 October 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20)
Front Cover: Creating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting (ChemPhysChem 20/2023)
- 17 October 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20) , e202300670
Creating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting
The front cover artwork is provided by Hang Liu from Prof. Dr. Joachim Albrecht's and Prof. Dr. Katharina Weber's group at Aalen University. The image depicts the wetting properties of a biopolymer foil. Surface microstructuring allows the tailoring of physical chemical properties that can lead to biodegradable packaging foils. Read the full text of the Research Article at 10.1002/cphc.202300301.
- 17 October 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20) , e202300670
Creating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting
The front cover artwork is provided by Hang Liu from Prof. Dr. Joachim Albrecht's and Prof. Dr. Katharina Weber's group at Aalen University. The image depicts the wetting properties of a biopolymer foil. Surface microstructuring allows the tailoring of physical chemical properties that can lead to biodegradable packaging foils. Read the full text of the Research Article at 10.1002/cphc.202300301.
- Open Access
- 14 August 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20) , e202300301
Creating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting
The surface topography of biodegradable polymer foils is modified by mechanical imprinting on a submillimeter length scale. The created patterns strongly influence the wetting behavior and allow the preparation of hydrophobic surfaces with controlled solid‐liquid interaction. A detailed analysis of anisotropic surface patterns reveals that the observed effect arises from a combination of topographical and compositional changes that are introduced to the surface. As a main result it is found that an individual combination of material and structure is required for the production of water‐repellent biopolymer foils that are highly attractive for packaging applications.
- 14 August 2023
- Published by Wiley in Chemphyschem
- Vol. 24 (20) , e202300301
Open AccessCreating Hydrophobic Foils From Biopolymer Blends Using Mechanical Microimprinting
The surface topography of biodegradable polymer foils is modified by mechanical imprinting on a submillimeter length scale. The created patterns strongly influence the wetting behavior and allow the preparation of hydrophobic surfaces with controlled solid‐liquid interaction. A detailed analysis of anisotropic surface patterns reveals that the observed effect arises from a combination of topographical and compositional changes that are introduced to the surface. As a main result it is found that an individual combination of material and structure is required for the production of water‐repellent biopolymer foils that are highly attractive for packaging applications.