Tony Makdissy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tony Makdissy has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Baptiste Paulmier
CNRS, IJL UMR 7198, Universit de Lorraine, Nancy, France
1 shared publication- Firas Al-Mahmoud
CNRS, IJL, Université de Lorraine, 54000 Nancy, France
1 shared publication - Maria Garcia-Vigueras
Institut Universitaire de France, Rennes, France
1 shared publication - Omar Elmazria
Université de Lorraine, CNRS, IJL, F-54000 Nancy, France
1 shared publication - Pascal Nicolay
CiSMAT—Carinthia Institute for Smart Materials, Carinthia University of Applied Sciences, 9524 Villach, Austria
1 shared publication - Pierre-Souhaïl Jeltiri
CNRS, IJL UMR 7198, Universit de Lorraine, Nancy, France
1 shared publication
Latest Publications
- Open Access
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 137343-137351
3D Metal-Only Phoenix Cell and its Application for Transmit-Reflect-Array
This paper presents a 3D metal-only waveguide-based phoenix cell. The proposed cell uses open-ended waveguides, which allow a portion of the incident wave to pass through the phoenix cell. It thus has the ability to control both reflection and transmission phases. Its principle is analyzed in detail. Two metal-only transmit-reflect-array antennas are then designed. The proposed transmit-reflect-array antennas are able to produce both transmitted and reflected beams at 16GHz in the target directions simultaneously. One of the transmit-reflect-array antennas is fabricated using selective laser melting 3D printing technology. The measured results show that a good agreement between the simulated and measured radiation patterns is achieved. The side lobe and cross polarization levels at 16 GHz are -15.3 dB and -23.1 dB respectively. The measured gain of transmitted and reflected beams at 16GHz are 25.7 dBi and 24.1 dBi respectively. Both the simulation and measurement results fully demonstrate the capabilities of the proposed 3D metal-only phoenix cell.
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 137343-137351
Open Access3D Metal-Only Phoenix Cell and its Application for Transmit-Reflect-Array
This paper presents a 3D metal-only waveguide-based phoenix cell. The proposed cell uses open-ended waveguides, which allow a portion of the incident wave to pass through the phoenix cell. It thus has the ability to control both reflection and transmission phases. Its principle is analyzed in detail. Two metal-only transmit-reflect-array antennas are then designed. The proposed transmit-reflect-array antennas are able to produce both transmitted and reflected beams at 16GHz in the target directions simultaneously. One of the transmit-reflect-array antennas is fabricated using selective laser melting 3D printing technology. The measured results show that a good agreement between the simulated and measured radiation patterns is achieved. The side lobe and cross polarization levels at 16 GHz are -15.3 dB and -23.1 dB respectively. The measured gain of transmitted and reflected beams at 16GHz are 25.7 dBi and 24.1 dBi respectively. Both the simulation and measurement results fully demonstrate the capabilities of the proposed 3D metal-only phoenix cell.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (11) , 1-4
Wireless Strain and Temperature Monitoring in Reinforced Concrete Using Surface Acoustic Wave Sensors
Monitoring the health of civil engineering structures using implanted deformation, temperature and corrosion sensors would further improve maintenance and extend the service life of those structures. However, sensor integration poses a number of problems, due to the presence of cables and on-board electronics. Passive, wireless SAW sensors offer a very promising solution, here. We used commercial SAW devices mounted on steel rebars to carry out an initial feasibility study. Without cables or embedded electronics, we were able to measure the deformation of a concrete beam subjected to bending load. We were also able to measure the temperature continuously over a three-week period.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (11) , 1-4
Wireless Strain and Temperature Monitoring in Reinforced Concrete Using Surface Acoustic Wave Sensors
Monitoring the health of civil engineering structures using implanted deformation, temperature and corrosion sensors would further improve maintenance and extend the service life of those structures. However, sensor integration poses a number of problems, due to the presence of cables and on-board electronics. Passive, wireless SAW sensors offer a very promising solution, here. We used commercial SAW devices mounted on steel rebars to carry out an initial feasibility study. Without cables or embedded electronics, we were able to measure the deformation of a concrete beam subjected to bending load. We were also able to measure the temperature continuously over a three-week period.