Bharat Shrimant
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bharat Shrimant has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Christopher George Arges
Argonne National Laboratory
5 shared publications - Prakash P. Wadgaonkar
CSIR-National Chemical Laboratory
4 shared publications - Ulhas K. Kharul
Polymer Science and Engineering Division CSIR‐National Chemical Laboratory Pune India
3 shared publications - Bin Yang
Pennsylvania State University
2 shared publications - Byung Hee Ko
Center for Catalytic Science and Technology, Department of Chemical and Biomolecular Engineering, University of Delaware, Newark, USA
2 shared publications Chulsung Bae
Department of Chemistry and Chemical Biology, Rensselaer Polytechnic Institute, Troy, USA
2 shared publications
Latest Publications
- Open Access
- 10 June 2024
- Published by Wiley in Small Structures
- Vol. 5 (9)
Reducing Ohmic Resistances in Membrane Capacitive Deionization Using Micropatterned Ion‐Exchange Membranes, Ionomer Infiltrated Electrodes, and Ionomer‐Coated Nylon Meshes
Membrane capacitive deionization (MCDI) is an emerging water desalination platform that is compact, electrified, and does not require high‐pressure piping. Herein, highly conductive poly(phenylene alkylene) ion‐exchange membranes (IEMs) are micropatterned with different surface geometries for MCDI. The micropatterned membranes increase the interfacial area with the liquid stream leading to a 700 mV reduction in cell voltage when operating at constant current (2 mA cm−2; 2000 ppm NaCl feed) while improving the energy normalized adsorbed salt (ENAS) value by 1.4 times. Combining the micropatterned poly(phenylene alkylene) IEMs with poly(phenylene alkylene) ionomer‐filled electrodes reduces the cell voltage by 1000 mV and improves the ENAS values by 2.3 times relative to the base case. This reduction in cell voltage allows for higher current density operation (i.e., 3–4 mA cm−2) . The reduction in cell voltage is ascribed to the ameliorating ohmic resistances related to ion transport at the membrane‐process stream interface and in the carbon cloth electrode. Finally, porous ionic conductors are implemented into the spacer channel with flat and micropatterned IEM configurations and ionomer infiltrated electrodes. For the configuration with flat IEMs, the porous ionic conductor improves ENAS values across the current density regime (2–4 mA cm−2), while for micropatterned IEMs it gets improved only at 4 mA cm−2.
- 10 June 2024
- Published by Wiley in Small Structures
- Vol. 5 (9)
Open AccessReducing Ohmic Resistances in Membrane Capacitive Deionization Using Micropatterned Ion‐Exchange Membranes, Ionomer Infiltrated Electrodes, and Ionomer‐Coated Nylon Meshes
Membrane capacitive deionization (MCDI) is an emerging water desalination platform that is compact, electrified, and does not require high‐pressure piping. Herein, highly conductive poly(phenylene alkylene) ion‐exchange membranes (IEMs) are micropatterned with different surface geometries for MCDI. The micropatterned membranes increase the interfacial area with the liquid stream leading to a 700 mV reduction in cell voltage when operating at constant current (2 mA cm−2; 2000 ppm NaCl feed) while improving the energy normalized adsorbed salt (ENAS) value by 1.4 times. Combining the micropatterned poly(phenylene alkylene) IEMs with poly(phenylene alkylene) ionomer‐filled electrodes reduces the cell voltage by 1000 mV and improves the ENAS values by 2.3 times relative to the base case. This reduction in cell voltage allows for higher current density operation (i.e., 3–4 mA cm−2) . The reduction in cell voltage is ascribed to the ameliorating ohmic resistances related to ion transport at the membrane‐process stream interface and in the carbon cloth electrode. Finally, porous ionic conductors are implemented into the spacer channel with flat and micropatterned IEM configurations and ionomer infiltrated electrodes. For the configuration with flat IEMs, the porous ionic conductor improves ENAS values across the current density regime (2–4 mA cm−2), while for micropatterned IEMs it gets improved only at 4 mA cm−2.
- Open Access
- 25 February 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Selective phosphate removal with manganese oxide composite anion exchange membranes in membrane capacitive deionization
The discharge of excessive phosphorous into water bodies can lead to serious eutrophication threatening aquatic ecosystem. Membrane capacitive deionization (MCDI) is an effective platform for deionizing aqueous streams; however, conventional MCDI is unable to selectively remove targeted ions from a liquid mixture. In this work, we fabricated manganese oxide composite anion exchange membranes (AEMs) for MCDI to enhance phosphate removal selectivity from sodium chloride-sodium dihydrogen phosphate (10:1 molar ratio) aqueous mixtures. We systematically investigated several critical factors, such as constant current or voltage operation, applied voltage amount, process stream pH, and manganese oxide content in the AEM, on phosphate removal efficiency and phosphate selectivity. A trade-off was observed between phosphate removal and selectivity when increasing the cell voltage. Under the best conditions, an MCDI unit with a 20 wt% Mn2O3 composite AEM and a bipolar membrane facilitated high phosphate removal efficiency of ≥ 31.8 % and a phosphate over chloride selectivity of 1.1 while showing stability for at least 30 cycles. To help understand how manganese oxide particles boost AEM selectivity, static electronic structure calculations were performed, and they revelated that hydrogen phosphate absorption on Mn2O3 composite AEM was 314 kcal/mol more exothermic than that on pristine AEM while chloride adsorption on Mn2O3 composite AEM was 2.2 kcal/mol less exothermic than that on a pristine AEM. Overall, this work presents an effective strategy for selectively removing phosphate from model wastewater solutions and the mechanistic understanding that governs ion selectivity in composite ion-exchange membranes used in MCDI.
- 25 February 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessSelective phosphate removal with manganese oxide composite anion exchange membranes in membrane capacitive deionization
The discharge of excessive phosphorous into water bodies can lead to serious eutrophication threatening aquatic ecosystem. Membrane capacitive deionization (MCDI) is an effective platform for deionizing aqueous streams; however, conventional MCDI is unable to selectively remove targeted ions from a liquid mixture. In this work, we fabricated manganese oxide composite anion exchange membranes (AEMs) for MCDI to enhance phosphate removal selectivity from sodium chloride-sodium dihydrogen phosphate (10:1 molar ratio) aqueous mixtures. We systematically investigated several critical factors, such as constant current or voltage operation, applied voltage amount, process stream pH, and manganese oxide content in the AEM, on phosphate removal efficiency and phosphate selectivity. A trade-off was observed between phosphate removal and selectivity when increasing the cell voltage. Under the best conditions, an MCDI unit with a 20 wt% Mn2O3 composite AEM and a bipolar membrane facilitated high phosphate removal efficiency of ≥ 31.8 % and a phosphate over chloride selectivity of 1.1 while showing stability for at least 30 cycles. To help understand how manganese oxide particles boost AEM selectivity, static electronic structure calculations were performed, and they revelated that hydrogen phosphate absorption on Mn2O3 composite AEM was 314 kcal/mol more exothermic than that on pristine AEM while chloride adsorption on Mn2O3 composite AEM was 2.2 kcal/mol less exothermic than that on a pristine AEM. Overall, this work presents an effective strategy for selectively removing phosphate from model wastewater solutions and the mechanistic understanding that governs ion selectivity in composite ion-exchange membranes used in MCDI.
- 23 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (9) , 11206-11216
Desalting Plasma Protein Solutions by Membrane Capacitive Deionization
Plasma protein therapies are used by millions of people across the globe to treat a litany of diseases and serious medical conditions. One challenge in the manufacture of plasma protein therapies is the removal of salt ions (e.g., sodium, phosphate, and chloride) from the protein solution. The conventional approach to remove salt ions is the use of diafiltration membranes (e.g., tangential flow filtration) and ion-exchange chromatography. However, the ion-exchange resins within the chromatographic column as well as filtration membranes are subject to fouling by the plasma protein. In this work, we investigate the membrane capacitive deionization (MCDI) as an alternative separation platform for removing ions from plasma protein solutions with negligible protein loss. MCDI has been previously deployed for brackish water desalination, nutrient recovery, mineral recovery, and removal of pollutants from water. However, this is the first time this technique has been applied for removing 28% of ions (sodium, chloride, and phosphate) from human serum albumin solutions with less than 3% protein loss from the process stream. Furthermore, the MCDI experiments utilized highly conductive poly(phenylene alkylene)-based ion exchange membranes (IEMs). These IEMs combined with ionomer-coated nylon meshes in the spacer channel ameliorate Ohmic resistances in MCDI improving the energy efficiency. Overall, we envision MCDI as an effective separation platform in biopharmaceutical manufacturing for deionizing plasma protein solutions and other pharmaceutical formulations without a loss of active pharmaceutical ingredients.
- 23 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (9) , 11206-11216
Desalting Plasma Protein Solutions by Membrane Capacitive Deionization
Plasma protein therapies are used by millions of people across the globe to treat a litany of diseases and serious medical conditions. One challenge in the manufacture of plasma protein therapies is the removal of salt ions (e.g., sodium, phosphate, and chloride) from the protein solution. The conventional approach to remove salt ions is the use of diafiltration membranes (e.g., tangential flow filtration) and ion-exchange chromatography. However, the ion-exchange resins within the chromatographic column as well as filtration membranes are subject to fouling by the plasma protein. In this work, we investigate the membrane capacitive deionization (MCDI) as an alternative separation platform for removing ions from plasma protein solutions with negligible protein loss. MCDI has been previously deployed for brackish water desalination, nutrient recovery, mineral recovery, and removal of pollutants from water. However, this is the first time this technique has been applied for removing 28% of ions (sodium, chloride, and phosphate) from human serum albumin solutions with less than 3% protein loss from the process stream. Furthermore, the MCDI experiments utilized highly conductive poly(phenylene alkylene)-based ion exchange membranes (IEMs). These IEMs combined with ionomer-coated nylon meshes in the spacer channel ameliorate Ohmic resistances in MCDI improving the energy efficiency. Overall, we envision MCDI as an effective separation platform in biopharmaceutical manufacturing for deionizing plasma protein solutions and other pharmaceutical formulations without a loss of active pharmaceutical ingredients.
- Open Access
- 2 November 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Desalting plasma protein solutions by membrane capacitive deionization
Plasma protein therapies are used by millions of people across the globe to treat a litany of diseases and serious medical conditions. One challenge in the manufacture of plasma protein therapies is the removal of salt ions (e.g., sodium, phosphate, and chloride) from the protein solution. The conventional approach to remove salt ions is the use of diafiltration membranes (e.g., tangential flow filtration) and ion-exchange chromatography. However, the ion-exchange resins within the chromatographic column, as well as filtration membranes, are subject to fouling by the plasma protein. In this work, we investigate membrane capacitive deionization (MCDI) as an alternative separation platform for removing ions from plasma protein solutions with negligible protein loss. MCDI has been previously deployed for brackish water desalination, nutrient recovery, mineral recovery, and removing pollutants from water. However, this is the first time this technique has been applied for removing 28% of ions (sodium, chloride, and phosphate) from human serum albumin solutions with less than 3% protein loss from the process stream. Furthermore, the MCDI experiments utilized highly conductive poly(phenylene alkylene) based ion exchange membranes (IEMs). These IEMs combined with ionomer coated nylon meshes in the spacer channel ameliorate ohmic resistances in MCDI improving energy efficiency. Overall, we envision MCDI as an effective separation platform in biopharmaceutical manufacturing for deionizing plasma protein solutions and other pharmaceutical formulations without loss of active pharmaceutical ingredients.
- 2 November 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessDesalting plasma protein solutions by membrane capacitive deionization
Plasma protein therapies are used by millions of people across the globe to treat a litany of diseases and serious medical conditions. One challenge in the manufacture of plasma protein therapies is the removal of salt ions (e.g., sodium, phosphate, and chloride) from the protein solution. The conventional approach to remove salt ions is the use of diafiltration membranes (e.g., tangential flow filtration) and ion-exchange chromatography. However, the ion-exchange resins within the chromatographic column, as well as filtration membranes, are subject to fouling by the plasma protein. In this work, we investigate membrane capacitive deionization (MCDI) as an alternative separation platform for removing ions from plasma protein solutions with negligible protein loss. MCDI has been previously deployed for brackish water desalination, nutrient recovery, mineral recovery, and removing pollutants from water. However, this is the first time this technique has been applied for removing 28% of ions (sodium, chloride, and phosphate) from human serum albumin solutions with less than 3% protein loss from the process stream. Furthermore, the MCDI experiments utilized highly conductive poly(phenylene alkylene) based ion exchange membranes (IEMs). These IEMs combined with ionomer coated nylon meshes in the spacer channel ameliorate ohmic resistances in MCDI improving energy efficiency. Overall, we envision MCDI as an effective separation platform in biopharmaceutical manufacturing for deionizing plasma protein solutions and other pharmaceutical formulations without loss of active pharmaceutical ingredients.
- 18 August 2022
- Published by Springer Nature in Nature Catalysis
- Vol. 5 (8) , 738-745
Enhancing acetate selectivity by coupling anodic oxidation to carbon monoxide electroreduction
- 18 August 2022
- Published by Springer Nature in Nature Catalysis
- Vol. 5 (8) , 738-745
Enhancing acetate selectivity by coupling anodic oxidation to carbon monoxide electroreduction
- Open Access
- 3 March 2022
- Published by Springer Nature in Research Square
Enhancing acetate selectivity by coupling anodic oxidation in carbon monoxide electroreduction
Electrocatalytic conversion of carbon monoxide (CO) is being actively developed as a key component for tandem CO2 electrolysis. Significant effort has been devoted to engineering CO reduction electrocatalysts for better multi-carbon product selectivity. However, less attention has been paid to other performance parameters, such as liquid product concentration and purity, which are crucial for commercializing CO electrolysis. Here, we present an “internally coupled purification” strategy to substantially improve the acetate concentration and purity in CO electrolysis. This improvement was achieved by incorporating both an anode electrocatalyst with high ethanol partial oxidation activity as well as an anion-exchange membrane with high ethanol permeability and good alkaline stability. We have successfully demonstrated stable 120-hour continuous operation of the CO electrolyzer at a fixed current density of 200 mA cm− 2 and a full cell potential of < 2.3 V, producing an acetate product stream with a concentration of 1.9 M and a purity of 97.7%. By tuning the reaction conditions, we also showed that the concentration of the acetate production stream can be further increased to 7.6 M while maintaining a purity of > 99%. Additional mechanistic investigation revealed the roles of anode electrocatalysts and anion-exchange membranes in enhancing the acetate selectivity in CO electrolyzers. Finally, a techno-economic analysis shows that a highly concentrated liquid product stream is essential to reduce the energy consumption associated with the product separation.
- 3 March 2022
- Published by Springer Nature in Research Square
Open AccessEnhancing acetate selectivity by coupling anodic oxidation in carbon monoxide electroreduction
Electrocatalytic conversion of carbon monoxide (CO) is being actively developed as a key component for tandem CO2 electrolysis. Significant effort has been devoted to engineering CO reduction electrocatalysts for better multi-carbon product selectivity. However, less attention has been paid to other performance parameters, such as liquid product concentration and purity, which are crucial for commercializing CO electrolysis. Here, we present an “internally coupled purification” strategy to substantially improve the acetate concentration and purity in CO electrolysis. This improvement was achieved by incorporating both an anode electrocatalyst with high ethanol partial oxidation activity as well as an anion-exchange membrane with high ethanol permeability and good alkaline stability. We have successfully demonstrated stable 120-hour continuous operation of the CO electrolyzer at a fixed current density of 200 mA cm− 2 and a full cell potential of < 2.3 V, producing an acetate product stream with a concentration of 1.9 M and a purity of 97.7%. By tuning the reaction conditions, we also showed that the concentration of the acetate production stream can be further increased to 7.6 M while maintaining a purity of > 99%. Additional mechanistic investigation revealed the roles of anode electrocatalysts and anion-exchange membranes in enhancing the acetate selectivity in CO electrolyzers. Finally, a techno-economic analysis shows that a highly concentrated liquid product stream is essential to reduce the energy consumption associated with the product separation.
- 16 June 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (6) , 5858-5867
Ionomer Significance in Alkaline Direct Methanol Fuel Cell to Achieve High Power with a Quarternized Poly(terphenylene) Membrane
- 16 June 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (6) , 5858-5867
Ionomer Significance in Alkaline Direct Methanol Fuel Cell to Achieve High Power with a Quarternized Poly(terphenylene) Membrane
- 11 January 2019
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 56 (2) , 136-145
Aromatic polyesters containing cardo perhydrocumyl cyclohexylidene groups: Synthesis, characterization and gas permeation study
Three bisphenols containing cardo perhydrocumyl cyclohexylidene group, namely; 1,1-bis(4-hydroxyphenyl)-4-perhydrocumylcyclohexane, 1,1-bis(4-hydroxy-3-methylphenyl)-4-perhydrocumylcyclohexane and 1,1-bis(4-hydroxy-3,5-dimethylphenyl)-4-perhydrocumylcyclohexane were synthesized starting from p-cumyl phenol. Each of these bisphenols was polycondensed with both terephthaloyl chloride and isophthaloyl chloride by phase transfer-catalyzed interfacial polymerization to obtain a series of new aromatic polyesters. Inherent viscosities and number average molecular weights of polyesters were in the range 0.51-0.64 dL/g and 17390-41430 g/mol, respectively which indicated the formation of reasonably high molecular weight polymers. The detailed NMR studies revealed that axial and equatorial identity of the phenyl rings of bisphenols was retained in polyesters resulting in constitutional isomerism. Polyesters containing perhydrocumyl cyclohexylidene groups showed excellent solubility in organic solvents viz, chloroform, dichloromethane, 1,1,2,2-tetrachloroethane and tetrahydrofuran. The self-standing films of polyesters could be cast from their chloroform solution. The 10% weight loss temperatures and glass transition temperatures of polyesters were in the range 453–485 °C and 201–267 °C, respectively demonstrating their excellent thermal characteristics. The gas permeability study of polyesters was carried out for He, H2 and N2 by variable-volume method. An improvement in permeability and decrease in selectivity was observed due to symmetric methyl substituents while reverse trend was observed in case of polyesters with asymmetric methyl substituents.
- 11 January 2019
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 56 (2) , 136-145
Aromatic polyesters containing cardo perhydrocumyl cyclohexylidene groups: Synthesis, characterization and gas permeation study
Three bisphenols containing cardo perhydrocumyl cyclohexylidene group, namely; 1,1-bis(4-hydroxyphenyl)-4-perhydrocumylcyclohexane, 1,1-bis(4-hydroxy-3-methylphenyl)-4-perhydrocumylcyclohexane and 1,1-bis(4-hydroxy-3,5-dimethylphenyl)-4-perhydrocumylcyclohexane were synthesized starting from p-cumyl phenol. Each of these bisphenols was polycondensed with both terephthaloyl chloride and isophthaloyl chloride by phase transfer-catalyzed interfacial polymerization to obtain a series of new aromatic polyesters. Inherent viscosities and number average molecular weights of polyesters were in the range 0.51-0.64 dL/g and 17390-41430 g/mol, respectively which indicated the formation of reasonably high molecular weight polymers. The detailed NMR studies revealed that axial and equatorial identity of the phenyl rings of bisphenols was retained in polyesters resulting in constitutional isomerism. Polyesters containing perhydrocumyl cyclohexylidene groups showed excellent solubility in organic solvents viz, chloroform, dichloromethane, 1,1,2,2-tetrachloroethane and tetrahydrofuran. The self-standing films of polyesters could be cast from their chloroform solution. The 10% weight loss temperatures and glass transition temperatures of polyesters were in the range 453–485 °C and 201–267 °C, respectively demonstrating their excellent thermal characteristics. The gas permeability study of polyesters was carried out for He, H2 and N2 by variable-volume method. An improvement in permeability and decrease in selectivity was observed due to symmetric methyl substituents while reverse trend was observed in case of polyesters with asymmetric methyl substituents.