YZYue Zhao

Yue Zhao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yue Zhao has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A 90.4% Efficiency Hybrid Step-Up Converter with Clock-Free Controller and Shunt-Current-Reusing Techniques for Power Burst Applications

    by Pengda Qu, Zhiming Xiao, Yue Zhao

    This article presents a low ripple, high voltage-conversion-ratio (VCR = 6), two-stage step-up converter intended for power-burst applications. The first boost stage raises the battery voltage to a maximum of 35 V, while the subsequent low dropout regulator (LDO) stage suppresses the ripple of the final output. Unlike conventional structures in which control circuits operate above a ground-referenced rail, the proposed shunt-current-reusing technique places most of the control circuits within a narrow floating dropout region (VDROP) between the boost output (VBST) and the LDO output (VOUT), thereby achieving nearly 100% current efficiency through current recycling. Adaptive adjustment of VDROP (0.5 V at light load and 0.65 V at heavy load) balances output ripple against the loss of the LDO stage. Consequently, the proposed converter achieves both high efficiency (>85%) and low ripple (BW = 1.2 MHz) of the LDO stage yields a fast transient response (1 W) at high supply voltage (>20 V) while maintaining low quiescent current consumption under most load conditions (<10 mA), as exemplified by light detection and ranging (LiDAR), haptic sensors, and micro electromechanical system (MEMS) drivers.

  • Radiation hardened design of CMOS pixel sensor for the micro-vertex detector of the CBM experiment

    by Yue Zhao

    Développement d’un capteur à pixels CMOS durci aux radiations pour le détecteur de vertex de l’expérience CBM: L’expérience CBM (compressed baryonic matter) étudiera le diagramme de phase de la matière nucléaire à des densités extrêmes, en observant des collisions or-or ou proton-or. Le détecteur Microv Vertex (MVD), l’instrument le plus proche des collisions, est conçu à l'aide de capteurs à pixels CMOS. Ces collisions produisent de nombreuses particules très ionisantes, telles que des ions or, carbone ou des protons. Ces rayonnements peuvent générer différents types de perturbations dans les capteurs du MVD : effets d'événement unique (SEE), effets de dose d'ionisation totale (TID) et dommages par déplacement. Cette thèse propose une méthode de durcissement aux rayonnements par conception (RHDB) qui respecte les principales contraintes des capteurs imposées par l’expérience, notamment leur taille. En identifiant les fonctionnalités critiques du circuit et avec des simulations dédiées, nous introduisons une conception HRDB de manière sélective dans deux parties numériques des capteurs du MVD et réussissons ainsi à augmenter significativement leur résistances aux SEE. Il s’agit de l’architecture de lecture des données et d’un circuit à boucle de verrouillage (PLL).

  • A 60-V Chopper Amplifier Achieving 0.12- μ V Ripple and 2- μ V V OS Over Full Temperature With Calibration

    by Jingbin Feng, Shanshan Zhou, Peiru Hou, Pengda Qu, Yue Zhao, Zhiming Xiao

    This brief presents a 60 V chopper-stabilized operational amplifier (opamp) with an 8 MHz gain-bandwidth product (GBW) and precision calibration. A novel high-voltage adaptive clock-bootstrap technique is proposed, compensates for temperature variations of the threshold voltage, and maintains a constant overdrive voltage. The opamp integrates a $500\times $ gain module to amplify and calibrate the non-chopped offset voltage, thereby reducing output ripple. It adopts a calibration scheme with temperature-compensated bit weights which are proportional to the transconductance of the chopper-path input transistor pair. Fabricated in a 0.18- $\mu $ m Bipolar-CMOS-DMOS process, the amplifier employs input-referred offset and ripple minimization techniques while ensuring consistent performance over a wide input common-mode voltage range and temperature span, achieving a 3- $\sigma $ offset voltage of $2~\mu $ V across 100 samples (- $40~^{\circ }$ C to $125~^{\circ }$ C), an offset drift of 7 nV/°C, and a maximum input-referred ripple of $0.12~\mu $ VRMS(Root Mean Square).

  • A Temperature-Compensated, Low-Power, Microsecond-Response Power Gating Circuit With Triple-Mode Overload Protection

    by Jingbin Feng, Qiuzhen Xu, Khalil Yousef, Pengda Qu, Yue Zhao, Zhiming Xiao

    This article presents a power gating circuit with triple-mode overload protection, which can be integrated into low -ower charger or regulators for interface protection. It can respond in tens of microseconds while consuming 0.8 μA quiescent current under low-power mode conditions. A voltage-to-resistance converter is proposed to generate a resistance inversely proportional to the input supply voltage for setting the overload threshold. A temperature compensation mechanism is also integrated to maintain overload threshold deviations within ±2% over the −40 to 125 °C range. The mode control logic implements an auto-recovery function that automatically reconnects the power gating path after the overload condition clears. Fabricated in 0.18-μm Bipolar CMOS and DMOS (BCD) technology, the design operates over a 5–40 V range with an area of 0.35 mm2, achieving an RDSON of 600 mΩ for the integrated power switches. For over-power protection (threshold: 1.2 W), the power conduction path is turned off with a response time of 17 μs under an abrupt 3 W power surge. For over-current protection (threshold: 106 mA), the path is shut down within 12 μs upon an abrupt 300 mA load current surge. For over-voltage protection (threshold: 24 V) for an abrupt voltage transition from 10 to 40 V, the conduction path is cut off within 1 μs via slope detection.

  • A Symmetrical Inductor Current Modulated Buck Converter With Spread-Spectrum Scheme for Low EMI and Low Output Ripple

    by Jiarui Ren, Yadong Guo, Yikai Sun, Feng Luo, Yue Zhao, Zhiming Xiao

    This article proposes a symmetrical inductor current based spread-spectrum frequency modulation (SIC-SSFM) scheme for buck converters, aiming at optimizing both the electromagnetic interference (EMI) and the output voltage ripple. Compared with conventional frequency modulation approach, the proposed symmetrical structure helps minimize the averaged inductor current ripple and thus the output ripple. By utilizing the proposed method, the proposed buck converter eliminates the need for oscillators or any slope compensation, effectively optimizing the quiescent power consumption. The proposed converter supports input and output ranges of 5–40 V and 3.3–5 V, respectively. It is capable of delivering 2A maximum load while consumes only 8.4 μA quiescent current. The measured output ripple is 9–12.5 mV, achieving a peak efficiency of 93.36%, while the measured EMI is reduced by 18.5 dB due to the proposed SIC-SSFM. The active SIC-SSFM circuit occupies an area of 0.06 mm2, with a total buck area of 2.32 mm×1.88 mm.


  • An Ultra-Low Noise and Wide Output Range LDO With BJT Input Stage and Base Current Cancellation Technique

    by Yun Li, Jiarun Jiang, Pengda Qu, Yue Zhao, Feng Luo, Zhiming Xiao

    An LDO that utilizes Bipolar-Junction-Transistor (BJT) as input differential pair with base current compensation structure is proposed. The NPNs and PNPs complementary input structure is designed to suppress both the flicker and thermal noise of the LDO and ensure the rail-to-rail common mode input range. The base current compensation structure is designed to ensure the output accuracy of the LDO. Moreover, by designing the current-mode reference, the proposed LDO eliminates the thermal noise from the feedback resistor network and the amplification of the noise due to the feedback coefficient. The proposed LDO was fabricated with 180nm BCD double well process with a die area of about 2.884mm $^{\mathbf{2}}$. The measured output noise of the LDO is only $\mathbf{248nV/}\sqrt {\mathbf{Hz}} $ at 10Hz, and the integrated RMS noise is 1.44$\mu $V from 10Hz to 100kHz. The LDO supports a wide supply rail range from 2.3V to 20V and a wide output range from 0.1V to 19.7V. The measured Line and Load regulations are 0.035mV/V and 0.0008mV/mA, respectively.


  • Open Access

    A high efficiency adaptively biased LDO with frequency modulated charge pump for NMOS output stage

    by Shansong Huang, Yue Zhao, Zhiming Xiao

    This paper presents an adaptive biased NMOS LDO which contains an adaptively biased pulse-frequency-modulated (PFM) charge pump to improve efficiency. Compared with conventional architecture, the ground current of the proposed LDO is halved under 3mA load current by regulating the charge pump frequency based on the sensed output current. In addition, the power supply rejection is also improved to 66dB @ 10 kHz due to the relatively stable charge pumped. The proposed LDO achieved 99.995% current efficiency under 1A load. The proposed LDO was built with 0.18μm BCD technology. The simulated line and load regulations were 0.199mV/V and 53nV/mA, respectively.


  • Pixel-Level Clustering Algorithm for Data Reconstruction in ILC

    by R. Zhao, R. Zheng, X. Wei, F. Xue, J. Wang, Y. Zhao, C. Hu-Guo, Y. Hu

    A high amount of hits on the vertex detector of the International Linear Collider are generated by the beam background, which leads to an increase in the data flow of the detector system. Charged particles coming from the beam background have low momentum, resulting in the generation of elongated clusters. The CMOS pixel sensor, which integrates pre-processing functions and on-chip artificial neural networks, could remove these elongated clusters. Clustering is the first step for data pre-processing and is used to collect clusters from raw data. In this paper, a pixel-level clustering algorithm with a 5×5 window executed in real-time is proposed. The algorithm is tested using 4500 frames (500 frames for each angle of incidence) of raw data (12bits/pixel) from a MIMOSA-18 sensor and compared to conventional clustering algorithms. The clustering implementation for an example array of 5×5 pixels is synthesized for different frequencies (100 and 200MHz) and ADC resolutions (4 and 8bits). The power dissipation and occupied area of the different implementations are analyzed. The hardware implementation of the algorithm provides the possibility to integrate the clustering function into the CMOS pixel sensor.


  • Implementation of The High-Speed SM4 Cryptographic Algorithm Based On Random Pseudo Rounds

    by Siliang Suo, Chao Cui, Ganyang Jian, Xiaoyun Kuang, Yiwei Yang, Yun Zhao, Kaitian Huang

    The SM4 cryptographic algorithm is one of the standards of commercial cryptographic algorithm in China, which is used widely in the data encryption and other application scenarios for the advantages of less resources and fast speed. The attackers attack the first and last round of SM4 algorithm generally in the side channel attack. The number of the invalid random rounds before and after the SM4 cryptographic algorithm can make the side channel information collected by the attacker invalid in order to resist the side channel attack; At the same time, the multistage pipelining method is adopted to realize the SM4 cryptographic algorithm at the high speed, that is, four rounds of operations are realized every cycle, and one SM4 grouping operation is completed in eight cycles. The implementation results of the FPGA show that the clock frequency of SM4 cipher operation is up to 100MHz and the throughput rate under ECB mode is up to 1.6gbps, which has the advantages of high performance and anti-side channel attack.