Soontorn Odngam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Soontorn Odngam has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Chaiyut Sumpavakup
Research Centre for Combustion Technology and Alternative Energy—CTAE, and College of Industrial Technology, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
3 shared publications - Chokchai Anamtawach
Department of Power Engineering Technology, College of Industrial Technology, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
1 shared publication - Natee Tanman
Research Centre for Combustion Technology and Alternative Energy–CTAE and College of Industrial Technology, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
1 shared publication - Patiparn Intacharoen
Department of Power Engineering Technology, College of Industrial Technology, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
1 shared publication - Thanachit Thongtaweewattana
Department of Power Engineering Technology, College of Industrial Technology, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
1 shared publication
Latest Publications
- Open Access
- 14 November 2026
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 17 (11) , 599
Design and Experimental Evaluation of a Lookahead-PD Control Architecture for Autonomous Lane Keeping Assist in Low-Speed Electric Vehicles
Advanced Driver Assistance Systems (ADASs), such as Lane Keeping Assist Systems (LKASs), play a crucial role in enhancing lateral stability and reducing road departure accidents in autonomous vehicles. However, latency from vision processing, communication, and electromechanical steering actuators, combined with physical non-linearities like gear backlash, introduces phase lag and tracking instability in low-speed electric vehicles. To address these challenges, this paper presents a real-time Lookahead-Proportional-Derivative (PD) control architecture tailored for low-speed autonomous electric vehicles. The proposed system features a decoupled framework combining a predictive outer loop—utilizing classical computer vision (Inverse Perspective Mapping, histogram analysis, and quadratic curve fitting) for preview error calculation—with a high-rate (1 kHz) PD-controlled inner loop. Physical plant dynamics and a 5-degree steering backlash were identified through empirical step-response system identification to optimize controller gains without integrator windup. Full-scale vehicle experiments on a modified golf cart platform demonstrated that the Lookahead-PD architecture effectively provides phase lead compensation against systemic delays (50.7–130.0 ms). The controller achieved an average settling time of 0.0347 s, a maximum transient overshoot of 5.81%, and a steady-state tracking error of 4.94% without hunting oscillations. These findings confirm that integrating predictive lookahead geometry with a derivative-dominant inner controller offers a robust, resource-efficient solution for latency-resilient lateral guidance in low-cost autonomous electric vehicles.
- 14 November 2026
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 17 (11) , 599
Open AccessDesign and Experimental Evaluation of a Lookahead-PD Control Architecture for Autonomous Lane Keeping Assist in Low-Speed Electric Vehicles
Advanced Driver Assistance Systems (ADASs), such as Lane Keeping Assist Systems (LKASs), play a crucial role in enhancing lateral stability and reducing road departure accidents in autonomous vehicles. However, latency from vision processing, communication, and electromechanical steering actuators, combined with physical non-linearities like gear backlash, introduces phase lag and tracking instability in low-speed electric vehicles. To address these challenges, this paper presents a real-time Lookahead-Proportional-Derivative (PD) control architecture tailored for low-speed autonomous electric vehicles. The proposed system features a decoupled framework combining a predictive outer loop—utilizing classical computer vision (Inverse Perspective Mapping, histogram analysis, and quadratic curve fitting) for preview error calculation—with a high-rate (1 kHz) PD-controlled inner loop. Physical plant dynamics and a 5-degree steering backlash were identified through empirical step-response system identification to optimize controller gains without integrator windup. Full-scale vehicle experiments on a modified golf cart platform demonstrated that the Lookahead-PD architecture effectively provides phase lead compensation against systemic delays (50.7–130.0 ms). The controller achieved an average settling time of 0.0347 s, a maximum transient overshoot of 5.81%, and a steady-state tracking error of 4.94% without hunting oscillations. These findings confirm that integrating predictive lookahead geometry with a derivative-dominant inner controller offers a robust, resource-efficient solution for latency-resilient lateral guidance in low-cost autonomous electric vehicles.
- Open Access
- 13 December 2024
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 15 (12) , 576
The Design of Distance-Warning and Brake Pressure Control Systems Incorporating LiDAR Technology for Use in Autonomous Vehicles
This research presents the design of a brake fluid pressure warning and control system for autonomous vehicles (AVs) used on university campuses to control brake fluid pressure and measure the proximity of objects or obstacles in front of the vehicles using LiDAR. The goal was to reduce the jerking of the vehicle caused by the conventional braking system, which may cause danger to the user. We initially changed the existing brake system, which uses human braking force, to electric motor braking and tested it in a closed area (a test track) before actual use. This research was divided into two parts: Part 1—using LiDAR to create warnings in case there are obstacles in front of the vehicle and Part 2—controlling brake fluid pressure using a linear motor and a PD controller. Under the test conditions employed, at a speed of 20 km/h, the total load of passengers is 600 kg. The design results regarding the PD controller with the most suitable values of the system that prevent the vehicle from jerking are KD = 27.9606 and KP = 32.0490. The test was conducted while an object crossed the vehicle’s path at distances of 5, 10, 15, and 20 m, respectively. It was found that controlling brake fluid pressure by measuring the distance from the object helped reduce the braking time and jerking of the vehicle and could stop the vehicle before experiencing a collision. At a distance of 20 m, the vehicle could be stopped before the crash and was 3.7 m away from the object; at a distance of 15 m, the distance from the object was 3.1 m; and at a distance of 10 m, the distance from the object was 3 m. However, at a distance of 5 m, the brake system could not stop the vehicle, causing collision with the object because the distance from the object for braking was less than the designed distance. This shows that the warning system and the brake fluid pressure control system can operate in accordance with the corresponding conditions correctly, smoothly, and quickly within the specified distance and be applied to other types of vehicles.
- 13 December 2024
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 15 (12) , 576
Open AccessThe Design of Distance-Warning and Brake Pressure Control Systems Incorporating LiDAR Technology for Use in Autonomous Vehicles
This research presents the design of a brake fluid pressure warning and control system for autonomous vehicles (AVs) used on university campuses to control brake fluid pressure and measure the proximity of objects or obstacles in front of the vehicles using LiDAR. The goal was to reduce the jerking of the vehicle caused by the conventional braking system, which may cause danger to the user. We initially changed the existing brake system, which uses human braking force, to electric motor braking and tested it in a closed area (a test track) before actual use. This research was divided into two parts: Part 1—using LiDAR to create warnings in case there are obstacles in front of the vehicle and Part 2—controlling brake fluid pressure using a linear motor and a PD controller. Under the test conditions employed, at a speed of 20 km/h, the total load of passengers is 600 kg. The design results regarding the PD controller with the most suitable values of the system that prevent the vehicle from jerking are KD = 27.9606 and KP = 32.0490. The test was conducted while an object crossed the vehicle’s path at distances of 5, 10, 15, and 20 m, respectively. It was found that controlling brake fluid pressure by measuring the distance from the object helped reduce the braking time and jerking of the vehicle and could stop the vehicle before experiencing a collision. At a distance of 20 m, the vehicle could be stopped before the crash and was 3.7 m away from the object; at a distance of 15 m, the distance from the object was 3.1 m; and at a distance of 10 m, the distance from the object was 3 m. However, at a distance of 5 m, the brake system could not stop the vehicle, causing collision with the object because the distance from the object for braking was less than the designed distance. This shows that the warning system and the brake fluid pressure control system can operate in accordance with the corresponding conditions correctly, smoothly, and quickly within the specified distance and be applied to other types of vehicles.
- Open Access
- 7 November 2023
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 14 (11) , 306
Experimental Investigation on Affecting Air Flow against the Maximum Temperature Difference of a Lithium-Ion Battery with Heat Pipe Cooling
Research on battery thermal management systems (BTMSs) is particularly significant since the electric vehicle sector is growing in importance and because the batteries that power them have high operating temperature requirements. Among them, heat pipe (HP)-based battery thermal management systems have very high heat transfer performance but fall short in maintaining uniform temperature distribution. This study presented forced air cooling by an axial fan as a method of improving the cooling performance of flat heat pipes coupled with aluminum fins (FHPAFs) and investigated the impact of air velocity on the battery pack’s maximum temperature differential (ΔTmax). All experiments were conducted on lithium nickel manganese cobalt oxide (NMC) pouch battery cells with a 20 Ah capacity in seven series connections at room temperature, under forced and natural convection, at various air velocity values (12.7 m/s, 9.5 m/s, and 6.3 m/s), and with 1C, 2C, 3C, and 4C discharge rates. The results indicated that at the same air velocity, increasing the discharge rate increases the ΔTmax significantly. Forced convection has a higher ΔTmax than natural convection. The ΔTmax was reduced when the air velocity was increased during forced convection.
- 7 November 2023
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 14 (11) , 306
Open AccessExperimental Investigation on Affecting Air Flow against the Maximum Temperature Difference of a Lithium-Ion Battery with Heat Pipe Cooling
Research on battery thermal management systems (BTMSs) is particularly significant since the electric vehicle sector is growing in importance and because the batteries that power them have high operating temperature requirements. Among them, heat pipe (HP)-based battery thermal management systems have very high heat transfer performance but fall short in maintaining uniform temperature distribution. This study presented forced air cooling by an axial fan as a method of improving the cooling performance of flat heat pipes coupled with aluminum fins (FHPAFs) and investigated the impact of air velocity on the battery pack’s maximum temperature differential (ΔTmax). All experiments were conducted on lithium nickel manganese cobalt oxide (NMC) pouch battery cells with a 20 Ah capacity in seven series connections at room temperature, under forced and natural convection, at various air velocity values (12.7 m/s, 9.5 m/s, and 6.3 m/s), and with 1C, 2C, 3C, and 4C discharge rates. The results indicated that at the same air velocity, increasing the discharge rate increases the ΔTmax significantly. Forced convection has a higher ΔTmax than natural convection. The ΔTmax was reduced when the air velocity was increased during forced convection.