Lu Qu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lu Qu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Kun Wang
School of transportation and civil engineering, Shandong Jiaotong University, Jinan 250357, China
3 shared publications - Peng Hu
School of Transportation and Civil Engineering, Shandong Jiaotong University
3 shared publications - Hao Xu
Civil Engineering Department, Shandong Jiaotong University, Jinan 250300, China
2 shared publications - Liran Fan
Civil Engineering Department, Shandong Jiaotong University, Jinan 250300, China
2 shared publications - Xiongao Li
Civil Engineering Department, Shandong Jiaotong University, Jinan 250300, China
2 shared publications - Hao Xu
Civil Engineering Department, Shandong Jiaotong University, Jinan 250300, China
1 shared publication
Latest Publications
- Open Access
Investigation on the Performance of Modified Corn Stalk Fiber AC-13 Asphalt Mixture
As an agricultural waste, a large amount of corn stalk will cause environmental pollution. In order to realize the resource utilization of waste and meet the strict requirements of modern traffic on pavement strength and durability, it was modified and applied to an AC-13 asphalt mixture to study its influence on the road performance of asphalt mixture and its mechanism. The road performances of modified corn stalk fiber, lignin fiber, and ordinary asphalt mixtures were evaluated via the wheel tracking test, low-temperature bending test, water immersion Marshall test, freeze–thaw splitting test, and fatigue test. Based on the results of three-point bending fatigue test, the viscoelastic parameters and indexes of the fiber asphalt mixture were obtained by fitting the loading specimen and deflection data with the Burgers constitutive model, and the creep strain response was analyzed by applying dynamic load, so as to explore the relationship between the viscoelastic characteristics and creep behavior of modified corn stalk fiber and AC-13 mixture. The long-term high-temperature performance test of the asphalt mixture with the best fiber content was carried out by using the long-term pavement intelligent monitoring equipment independently developed by the group of investigators. According to the findings, the ideal fiber contents for modified corn and lignin in asphalt mixture are 0.2% and 0.3%, respectively. Among them, the modified corn stalk fiber with a 0.2% content has the best effect on road performance, viscoelastic performance, and the asphalt mixture’s creep behavior under dynamic load. Compared with the 0.3% lignin fiber asphalt mixture, its dynamic stability, bending stiffness modulus, immersion residual stability, freeze–thaw splitting strength ratio, and loading times at failure increased by 19.9%, 18.28%, 4.19%, 8.6%, and 9.15%, respectively. Compared with ordinary asphalt mixture, it increased by 47.0%, 28.72%, 7.65%, 15%, and 75.81%, respectively. Moreover, when modified corn stalk fiber is added at 0.2%, the viscoelastic delay time of asphalt mixture is the longest, the strain peak value and rut depth are at a minimum, and the viscoelastic properties, creep properties, and long-term high-temperature properties are the best.
Open AccessInvestigation on the Performance of Modified Corn Stalk Fiber AC-13 Asphalt Mixture
As an agricultural waste, a large amount of corn stalk will cause environmental pollution. In order to realize the resource utilization of waste and meet the strict requirements of modern traffic on pavement strength and durability, it was modified and applied to an AC-13 asphalt mixture to study its influence on the road performance of asphalt mixture and its mechanism. The road performances of modified corn stalk fiber, lignin fiber, and ordinary asphalt mixtures were evaluated via the wheel tracking test, low-temperature bending test, water immersion Marshall test, freeze–thaw splitting test, and fatigue test. Based on the results of three-point bending fatigue test, the viscoelastic parameters and indexes of the fiber asphalt mixture were obtained by fitting the loading specimen and deflection data with the Burgers constitutive model, and the creep strain response was analyzed by applying dynamic load, so as to explore the relationship between the viscoelastic characteristics and creep behavior of modified corn stalk fiber and AC-13 mixture. The long-term high-temperature performance test of the asphalt mixture with the best fiber content was carried out by using the long-term pavement intelligent monitoring equipment independently developed by the group of investigators. According to the findings, the ideal fiber contents for modified corn and lignin in asphalt mixture are 0.2% and 0.3%, respectively. Among them, the modified corn stalk fiber with a 0.2% content has the best effect on road performance, viscoelastic performance, and the asphalt mixture’s creep behavior under dynamic load. Compared with the 0.3% lignin fiber asphalt mixture, its dynamic stability, bending stiffness modulus, immersion residual stability, freeze–thaw splitting strength ratio, and loading times at failure increased by 19.9%, 18.28%, 4.19%, 8.6%, and 9.15%, respectively. Compared with ordinary asphalt mixture, it increased by 47.0%, 28.72%, 7.65%, 15%, and 75.81%, respectively. Moreover, when modified corn stalk fiber is added at 0.2%, the viscoelastic delay time of asphalt mixture is the longest, the strain peak value and rut depth are at a minimum, and the viscoelastic properties, creep properties, and long-term high-temperature properties are the best.
- Open Access
- 15 February 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (4) , 1608
Structural Response of a Cement Concrete Pavement with a Buffer Layer to Temperature and Moving-Load Effects
The main issues associated with cement concrete pavements are cracks and broken plates that affect driving comfort and road service life. To ensure sustainable use of the cement concrete, a buffer layer (AC-10) can be introduced between the base and the cement concrete panel. In this study, the interlayer shear test was performed, and the interlayer bonding coefficient under different temperature conditions was determined. The creep test of the buffer layer was also conducted, and the four parameters (E1, E2, η1, and η2) of the Burgers model of the buffer layer were analyzed using regression. According to the parameters obtained from the test, the finite-element model was established, and the moving load was applied to analyze the structural model response under high-, medium-, and low-temperature conditions. The results show that the (1) temperature stress is mainly concentrated in the buffer layer and regions above the structural layer. At low temperatures, the maximum stress at the top of the surface layer is 2.16 MPa, and the vertical strain decreases as a function of depth. (2) Under the combined action of temperature and moving load, the variation ranges of tensile and compressive stresses at the top of the surface layer are the largest; the variation range of the buffer layer and the subsequent structure is small; the maximum warpage deformation of the surface layer is 0.453 mm under high-temperature conditions; and the maximum compression deformation is 0.219 mm under low-temperature conditions. (3) The comprehensive coefficient of the fatigue equation was modified, and the comprehensive coefficient of the fatigue equation under different vehicle speeds was proposed. This study provides a reference for the sustainable development of cement concrete pavements with buffer layers.- 15 February 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (4) , 1608
Open AccessStructural Response of a Cement Concrete Pavement with a Buffer Layer to Temperature and Moving-Load Effects
The main issues associated with cement concrete pavements are cracks and broken plates that affect driving comfort and road service life. To ensure sustainable use of the cement concrete, a buffer layer (AC-10) can be introduced between the base and the cement concrete panel. In this study, the interlayer shear test was performed, and the interlayer bonding coefficient under different temperature conditions was determined. The creep test of the buffer layer was also conducted, and the four parameters (E1, E2, η1, and η2) of the Burgers model of the buffer layer were analyzed using regression. According to the parameters obtained from the test, the finite-element model was established, and the moving load was applied to analyze the structural model response under high-, medium-, and low-temperature conditions. The results show that the (1) temperature stress is mainly concentrated in the buffer layer and regions above the structural layer. At low temperatures, the maximum stress at the top of the surface layer is 2.16 MPa, and the vertical strain decreases as a function of depth. (2) Under the combined action of temperature and moving load, the variation ranges of tensile and compressive stresses at the top of the surface layer are the largest; the variation range of the buffer layer and the subsequent structure is small; the maximum warpage deformation of the surface layer is 0.453 mm under high-temperature conditions; and the maximum compression deformation is 0.219 mm under low-temperature conditions. (3) The comprehensive coefficient of the fatigue equation was modified, and the comprehensive coefficient of the fatigue equation under different vehicle speeds was proposed. This study provides a reference for the sustainable development of cement concrete pavements with buffer layers. - Open Access
Influence of Modified Stalk Fibers on the Fatigue Performance of Asphalt Binder
The type and content of modified stalk fibers significantly influence the fatigue properties of asphalt binder. In this study, different concentrations of NaOH solution were used to modify stalk fibers, and scanning electron microscopy (SEM) was used to observe the effect of the modified concentration on the fiber morphology. A dynamic shear rheology (DSR) test and a linear amplitude sweep (LAS) test were conducted to analyze the effects of the fiber type and content on various factors such as the complex shear modulus G*, phase angle δ, and fatigue parameters (A35 and B). Consequently, the fatigue life Nf of the fiber asphalt binder was calculated using a viscoelastic continuum damage model. The results show that stalk fibers modified using a 5% alkali solution exhibited the best oil absorption and heat resistance, the asphalt binder with a 1.5%–2% fiber content exhibited the best resistance to fatigue, and the fatigue performance of the asphalt binder with different types of fibers was superior when fiber doping was at 1.5%. Additionally, the fatigue parameter A35 of the modified cotton and corn stover fibers increased by 40.5% and 57.6%, respectively, and the fatigue parameter B decreased by 5.8% and 4.8%, respectively, compared with that of the unmodified stover fibers. Finally, the modified corn stalk fiber asphalt binder with a 1.5% fiber content demonstrated the best fatigue resistance.
Open AccessInfluence of Modified Stalk Fibers on the Fatigue Performance of Asphalt Binder
The type and content of modified stalk fibers significantly influence the fatigue properties of asphalt binder. In this study, different concentrations of NaOH solution were used to modify stalk fibers, and scanning electron microscopy (SEM) was used to observe the effect of the modified concentration on the fiber morphology. A dynamic shear rheology (DSR) test and a linear amplitude sweep (LAS) test were conducted to analyze the effects of the fiber type and content on various factors such as the complex shear modulus G*, phase angle δ, and fatigue parameters (A35 and B). Consequently, the fatigue life Nf of the fiber asphalt binder was calculated using a viscoelastic continuum damage model. The results show that stalk fibers modified using a 5% alkali solution exhibited the best oil absorption and heat resistance, the asphalt binder with a 1.5%–2% fiber content exhibited the best resistance to fatigue, and the fatigue performance of the asphalt binder with different types of fibers was superior when fiber doping was at 1.5%. Additionally, the fatigue parameter A35 of the modified cotton and corn stover fibers increased by 40.5% and 57.6%, respectively, and the fatigue parameter B decreased by 5.8% and 4.8%, respectively, compared with that of the unmodified stover fibers. Finally, the modified corn stalk fiber asphalt binder with a 1.5% fiber content demonstrated the best fatigue resistance.