RZRan Zhang

Ran Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ran Zhang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on the Effect of Coupled Internal and External EGR on Homogeneous Charge Compression Ignition under High Pressure Rise Rate

    by Huayu Tian, Jun Wang, Ran Zhang, Fan Wang, Yan Su, Yaodong Wang

    This paper investigated the effects of exhaust gas recirculation (EGR) on homogeneous charge compression ignition (HCCI) combustion in internal combustion engines. The exhaust valve closing (EVC) timings were scanned to obtain a set of baseline operating points for HCCI, and the coupling control of the internal and external EGR was explored. The results indicate that external EGR delays HCCI ignition timing and slows down the combustion speed. As the internal EGR rate increases, the maximum external EGR ratio that can be tolerated decreases. For HCCI detonation operating points with low internal EGR rates, the addition of up to 10% of external EGR can control the pressure rise rate peak to less than 10 bar/°CA, resulting in reduced fuel consumption and increased indicated mean effective pressure (IMEP). However, for HCCI operating points with high internal EGR rates, the effect of external EGR is mainly observed in the control of the pressure rise rate, with limited increase in IMEP. Additionally, an increasing external EGR rate leads to a significant decrease in nitrogen oxide (NOx) emissions, while carbon monoxide (CO) and hydrocarbon (HC) emissions slightly increase before engine misfire occurs. These findings suggest that the coupling control of internal and external EGR should be explored further, particularly in relation to reducing the negative valve overlap (NVO) angle and improving combustion efficiency.


  • Open Access

    Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load

    by Jun Wang, Huayu Tian, Ran Zhang, Bo Shen, Yan Su, Hao Yu, Yulin Zhang

    The exceptional properties of methanol, such as its high octane number and latent heat of evaporation, make it an advantageous fuel for efficient utilization in dual-fuel combustion techniques. The aim of this study is to investigate the effect of direct methanol injection timing on the combustion, performance and emission characteristics of a dual-fuel spark ignition engine at different injection pressures. We conducted four different direct injection pressure tests ranging from 360° ahead to 30° CA ahead at 30° CA intervals. The experimental results indicate that regardless of the injection pressure, altering the methanol injection timing from −360° to −30° CA ATDC leads to distinct combustion behavior and changes in the combustion phase. Initially, as the injection timing is delayed, the combustion process accelerates, which is followed by a slower combustion phase. Additionally, the combustion phase itself experiences a delay and then advances. Regarding performance characteristics, both the brake thermal efficiency (BTE) and exhaust gas temperature (EGT) exhibit a consistent pattern of first increasing and then decreasing as the injection timing is delayed. This suggests that there is an optimal injection timing window that can enhance both the engine’s efficiency and its ability to manage exhaust temperature. In terms of emissions, there are different trends in this process due to the different conditions under which the individual emissions are produced, with CO and HC showing a decreasing and then increasing trend, and NOx showing the opposite trend. In conclusion, regardless of the injection pressure employed, adopting a thoughtful and well-designed injection strategy can significantly improve the combustion performance and emission characteristics of the engine. The findings of this study shed light on the potential of methanol dual-fuel combustion and provide valuable insights for optimizing engine operation in terms of efficiency and emissions control.


  • Open Access

    Experimental Study on Macroscopic Spray and Fuel Film Characteristics of E40 in a Constant Volume Chamber

    by Huayu Tian, Jun Wang, Ran Zhang, Yulin Zhang, Yan Su, Hao Yu, Bo Shen

    In the modern industrial field, there is a strong emphasis on energy-saving and emission reduction. Increasing the amount of ethanol in ethanol–gasoline blends has the potential to replace fossil fuel gasoline more effectively, improving energy efficiency and lowering emissions. The interaction between liquid fuel film generation on the piston crown and spray impingement in the combustion chamber in the setting of GDI engines has a substantial impact on particle emissions and engine combustion. In this study, 92# gasoline and ethanol by volume are combined to create the ethanol–gasoline blend E40. The spray characteristics and film properties of both gasoline and the intermediate proportion ethanol–gasoline blend E40 were researched utilizing a constant volume combustion platform and the schlieren method and refractive index matching (RIM) approach. The results show that, for 0.1–25 operating conditions, gasoline consistently displays greater macroscopic spray characteristic parameters than E40. This shows that gasoline fuel spray evaporation is superior to E40. Similar results are seen in the analysis of wall-attached fuel films, where the volume and thickness of the gasoline film are less than those of the E40 film under the given operating conditions. In contrast, E40 consistently exhibits stronger macroscopic spray characteristic values than gasoline under the 0.1–150 and 0.4–150 operating conditions, along with lower film thickness and volume. As a result, under these two operating conditions, E40 fuel performs better during spray evaporation.