Ahmed Altaher Omer Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmed Altaher Omer Ahmed has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- László Bejó
Institute of Applied Sciences, Faculty of Wood Engineering and Creative Industry, University of Sopron, 9400 Sopron, Hungary
4 shared publications - József Garab
Institute of Applied Sciences, Faculty of Wood Engineering and Creative Industry, University of Sopron, 9400 Sopron, Hungary
2 shared publications - Tibor Alpár
Institute of Applied Sciences, Faculty of Wood Engineering and Creative Industry, University of Sopron, 9400 Sopron, Hungary
2 shared publications - Csilla Csiha
Faculty of Wood Engineering and Creative Industries, University of Sopron, 9400 Sopron, Hungary
1 shared publication - Erika Horváth-Szováti
Soproni Egyetem, Faipari Mérnöki és Kreatívipari Kar, Alaptudományi Intézet
1 shared publication - János Kozelka
Faculty of Wood Engineering and Creative Industries, University of Sopron, 9400 Sopron, Hungary
1 shared publication
Latest Publications
- Open Access
- 17 November 2026
- Published by MDPI AG in Environmental and Earth Sciences Proceedings
- Vol. 49 (1) , 3
Underutilised Sudanese Hardwood Species as Sustainable Construction Materials: An Engineering Assessment of the Property Record
Sudan holds roughly 29.8 million ha of forest and 24.9 million ha of other wooded land, and these resources are used overwhelmingly for energy rather than for construction. This paper is a critical assessment of the published wood-property record for eight Sudanese hardwood species—Anogeissus leiocarpus, Balanites aegyptiaca, Acacia nilotica, Khaya senegalensis, Eucalyptus camaldulensis, Azadirachta indica, Sclerocarya birrea and Commiphora africana—and of what that record does, and does not, support for structural timber and engineered wood products. No new experimental work is reported: all values are taken from the published literature, every value is printed with its source and the type of that source is named, and values that could not be traced to an identified study or a verifiable database entry were withdrawn rather than reproduced. Three species carry a strength class assigned in a primary Sudanese study, but from small clear specimens rather than the structural-size members EN 384 presupposes, and for one of the three the stiffness in the record is about 30% below the mean modulus of elasticity that the assigned class requires. For Khaya senegalensis and Azadirachta indica, no Sudanese measurement of density or strength was traced; values exist only for material grown elsewhere in Africa and are reported here as such. Natural durability has not been determined on Sudanese material for any of the eight species. A second constraint is regulatory rather than material: the EN 338 C-classes, EN 14080 and ANSI/APA PRG 320 are written for softwoods, so hardwood products are routed instead through EN 16737 visual grading, EN 384 testing and European Assessment Documents. The binding constraints on structural use are therefore the absence of characteristic values, of accredited testing, and of kiln drying, not the timber itself.
- 17 November 2026
- Published by MDPI AG in Environmental and Earth Sciences Proceedings
- Vol. 49 (1) , 3
Open AccessUnderutilised Sudanese Hardwood Species as Sustainable Construction Materials: An Engineering Assessment of the Property Record
Sudan holds roughly 29.8 million ha of forest and 24.9 million ha of other wooded land, and these resources are used overwhelmingly for energy rather than for construction. This paper is a critical assessment of the published wood-property record for eight Sudanese hardwood species—Anogeissus leiocarpus, Balanites aegyptiaca, Acacia nilotica, Khaya senegalensis, Eucalyptus camaldulensis, Azadirachta indica, Sclerocarya birrea and Commiphora africana—and of what that record does, and does not, support for structural timber and engineered wood products. No new experimental work is reported: all values are taken from the published literature, every value is printed with its source and the type of that source is named, and values that could not be traced to an identified study or a verifiable database entry were withdrawn rather than reproduced. Three species carry a strength class assigned in a primary Sudanese study, but from small clear specimens rather than the structural-size members EN 384 presupposes, and for one of the three the stiffness in the record is about 30% below the mean modulus of elasticity that the assigned class requires. For Khaya senegalensis and Azadirachta indica, no Sudanese measurement of density or strength was traced; values exist only for material grown elsewhere in Africa and are reported here as such. Natural durability has not been determined on Sudanese material for any of the eight species. A second constraint is regulatory rather than material: the EN 338 C-classes, EN 14080 and ANSI/APA PRG 320 are written for softwoods, so hardwood products are routed instead through EN 16737 visual grading, EN 384 testing and European Assessment Documents. The binding constraints on structural use are therefore the absence of characteristic values, of accredited testing, and of kiln drying, not the timber itself.
- Open Access
Multivariate Morphological Analysis of Indigenous and Hybrid Poplar Strands for Oriented Strand Board and Laminated Strand Lumber Production
Geometric uniformity in lignocellulosic furnish plays a central role in determining the mechanical reliability and density stratification of engineered wood products. This study presents a comprehensive morphological assessment of wood strands produced from indigenous poplar (Populus nigra L.) and hybrid poplar (Populus × euramericana (Dode) Guinier) strands under full industrial flaking conditions. A total of 600 strands were characterized for weight, length, width, and thickness and analyzed using a multivariate statistical framework integrating Principal Component Analysis (PCA) and bivariate correlation modeling. Despite being processed to the same nominal target length (120 mm), the two provenances exhibited markedly different dimensional behaviors. Hybrid poplar strands were substantially heavier (mean 0.536 g vs. 0.291 g) and slightly thicker on average, while indigenous strands were marginally wider; strand length did not differ significantly between provenances (p = 0.354). PCA applied to four variables (weight, length, width, and mean thickness) revealed that weight and width were the dominant contributors to PC1 (57.0% of total variance), enabling clear separation of the two provenances into distinct multivariate clusters. These findings indicate that hybrid furnish, due to its coarser and more variable geometry, may require enhanced mat densification during hot pressing to minimize internal voids and achieve a stable vertical density profile (VDP). The dataset and analytical approach presented here provide actionable insights for optimizing flaker calibration, strand classification, and resin dosing strategies in the production of Oriented Strand Board (OSB) and Laminated Strand Lumber (LSL), particularly when integrating fast-growing hybrid poplar resources into industrial manufacturing lines.
Open AccessMultivariate Morphological Analysis of Indigenous and Hybrid Poplar Strands for Oriented Strand Board and Laminated Strand Lumber Production
Geometric uniformity in lignocellulosic furnish plays a central role in determining the mechanical reliability and density stratification of engineered wood products. This study presents a comprehensive morphological assessment of wood strands produced from indigenous poplar (Populus nigra L.) and hybrid poplar (Populus × euramericana (Dode) Guinier) strands under full industrial flaking conditions. A total of 600 strands were characterized for weight, length, width, and thickness and analyzed using a multivariate statistical framework integrating Principal Component Analysis (PCA) and bivariate correlation modeling. Despite being processed to the same nominal target length (120 mm), the two provenances exhibited markedly different dimensional behaviors. Hybrid poplar strands were substantially heavier (mean 0.536 g vs. 0.291 g) and slightly thicker on average, while indigenous strands were marginally wider; strand length did not differ significantly between provenances (p = 0.354). PCA applied to four variables (weight, length, width, and mean thickness) revealed that weight and width were the dominant contributors to PC1 (57.0% of total variance), enabling clear separation of the two provenances into distinct multivariate clusters. These findings indicate that hybrid furnish, due to its coarser and more variable geometry, may require enhanced mat densification during hot pressing to minimize internal voids and achieve a stable vertical density profile (VDP). The dataset and analytical approach presented here provide actionable insights for optimizing flaker calibration, strand classification, and resin dosing strategies in the production of Oriented Strand Board (OSB) and Laminated Strand Lumber (LSL), particularly when integrating fast-growing hybrid poplar resources into industrial manufacturing lines.
- Open Access
Screw Withdrawal Performance of Hybrid Cross-Laminated Timber (CLT) Manufactured from Spruce (Picea abies), Beech (Fagus sylvatica) and Hungarian Poplar (Populus spp.)
Screw withdrawal force is a key mechanical property related to the load-bearing capacity and reliability of mechanically fastened timber structures. This study investigates the screw withdrawal performance of cross-laminated timber (CLT) manufactured from spruce, beech, and poplar, including both homogeneous and hybrid layups. The selected species represent materials with different densities and regional availability in Hungary. A one-component polyurethane adhesive was used for panel manufacturing. Screw withdrawal force was determined using two methods: a universal testing machine (UTM) and a manual portable device (MPD). The highest withdrawal forces were observed in beech-based configurations, while the lowest values were measured for spruce. Poplar-based configurations demonstrated intermediate but competitive performance, exceeding the reference spruce values. Statistical evaluation confirmed a significant effect of layup configuration on withdrawal resistance. The MPD measurements were on average approximately 9% higher than UTM results, indicating a consistent and quantifiable inter-method difference. The results demonstrate that hybrid CLT configurations can be optimized by combining species of different densities and that portable testing methods provide reliable estimates of withdrawal performance. These findings contribute to the understanding of connection behavior in hybrid CLT and support the practical application of semi-destructive testing methods for in-situ assessment.
Open AccessScrew Withdrawal Performance of Hybrid Cross-Laminated Timber (CLT) Manufactured from Spruce (Picea abies), Beech (Fagus sylvatica) and Hungarian Poplar (Populus spp.)
Screw withdrawal force is a key mechanical property related to the load-bearing capacity and reliability of mechanically fastened timber structures. This study investigates the screw withdrawal performance of cross-laminated timber (CLT) manufactured from spruce, beech, and poplar, including both homogeneous and hybrid layups. The selected species represent materials with different densities and regional availability in Hungary. A one-component polyurethane adhesive was used for panel manufacturing. Screw withdrawal force was determined using two methods: a universal testing machine (UTM) and a manual portable device (MPD). The highest withdrawal forces were observed in beech-based configurations, while the lowest values were measured for spruce. Poplar-based configurations demonstrated intermediate but competitive performance, exceeding the reference spruce values. Statistical evaluation confirmed a significant effect of layup configuration on withdrawal resistance. The MPD measurements were on average approximately 9% higher than UTM results, indicating a consistent and quantifiable inter-method difference. The results demonstrate that hybrid CLT configurations can be optimized by combining species of different densities and that portable testing methods provide reliable estimates of withdrawal performance. These findings contribute to the understanding of connection behavior in hybrid CLT and support the practical application of semi-destructive testing methods for in-situ assessment.
- Open Access
Comparative Analysis of Wettability of Hybrid and Indigenous Poplar Strands
The increasing demand for sustainable raw materials in engineered wood production has prompted the evaluation of alternative raw materials. In this context, indigenous black poplar (Populus nigra) was analyzed as a potential alternative, by testing its wettability, characterized by contact angle, determined by the sessile drop method, to predict its adhesion when used as strands for OSB and LSL production. Surface tension was tested on strands with a wide range of surface roughnesses. The results show minor but statistically significant difference in favor of black poplar, which has somewhat lower contact angle values (62.01°) than hybrid poplar (64.71°), based on 300 measurements each. The absorption of the liquid into the strands, evaluated on a smaller sample, follows a logarithmic relation with time. These results also show a slightly faster decrease in contact angle in case of indigenous poplar, compared to hybrid poplar. The results indicate that the adhesion of indigenous poplar strands does not present extra challenges, compared to the currently more frequent hybrid poplar strands.
Open AccessComparative Analysis of Wettability of Hybrid and Indigenous Poplar Strands
The increasing demand for sustainable raw materials in engineered wood production has prompted the evaluation of alternative raw materials. In this context, indigenous black poplar (Populus nigra) was analyzed as a potential alternative, by testing its wettability, characterized by contact angle, determined by the sessile drop method, to predict its adhesion when used as strands for OSB and LSL production. Surface tension was tested on strands with a wide range of surface roughnesses. The results show minor but statistically significant difference in favor of black poplar, which has somewhat lower contact angle values (62.01°) than hybrid poplar (64.71°), based on 300 measurements each. The absorption of the liquid into the strands, evaluated on a smaller sample, follows a logarithmic relation with time. These results also show a slightly faster decrease in contact angle in case of indigenous poplar, compared to hybrid poplar. The results indicate that the adhesion of indigenous poplar strands does not present extra challenges, compared to the currently more frequent hybrid poplar strands.
- Open Access
The Bending Properties of Hybrid Cross-Laminated Timber (CLT) Using Various Species Combinations
Cross-laminated timber (CLT) has become a massive commercial success in recent years due to its high performance, technological advantages, and low environmental impact. The finite softwood raw material supply has motivated researchers to find alternatives. This study presents an investigation of the viability of some Hungarian hardwood materials, such as CLT materials. Homogeneous beech, poplar, and spruce panels, as well as their combinations, were created using a polyurethane adhesive. The experimental results show the clear potential of Hungarian poplar, which performed much better than spruce. Poplar’s modulus of elasticity (MOE) and modulus of rupture (MOR) values reached or exceeded those of high-grade commercial softwood CLT. The bending properties of beech and hybrid beech–poplar panels far exceeded the performance of commercial panels, which shows the excellent potential of high-density hardwoods for high-performance CLT production. Beech–spruce hybrid panels seriously underperformed. This was caused by gluing issues, probably due to the large density differences between the two species, as evidenced by the glueline failure exhibited by most of these specimens during testing. The average panel density proved to be the best predictor of mechanical performance, except for beech–spruce hybrid panels.
Open AccessThe Bending Properties of Hybrid Cross-Laminated Timber (CLT) Using Various Species Combinations
Cross-laminated timber (CLT) has become a massive commercial success in recent years due to its high performance, technological advantages, and low environmental impact. The finite softwood raw material supply has motivated researchers to find alternatives. This study presents an investigation of the viability of some Hungarian hardwood materials, such as CLT materials. Homogeneous beech, poplar, and spruce panels, as well as their combinations, were created using a polyurethane adhesive. The experimental results show the clear potential of Hungarian poplar, which performed much better than spruce. Poplar’s modulus of elasticity (MOE) and modulus of rupture (MOR) values reached or exceeded those of high-grade commercial softwood CLT. The bending properties of beech and hybrid beech–poplar panels far exceeded the performance of commercial panels, which shows the excellent potential of high-density hardwoods for high-performance CLT production. Beech–spruce hybrid panels seriously underperformed. This was caused by gluing issues, probably due to the large density differences between the two species, as evidenced by the glueline failure exhibited by most of these specimens during testing. The average panel density proved to be the best predictor of mechanical performance, except for beech–spruce hybrid panels.