Sandra Gallegos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sandra Gallegos has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Alisa Lamorú Urgellés
Centro de Investigaciones del Níquel "Alberto Fernández Montes de Oca" (CEDINIQ), Moa, Holguín, Cuba
2 shared publications - Carlos Hernández Pedrera
Facultad de Ingeniería Química y Agronomía, Universidad de Oriente, Santiago de Cuba, Cuba
2 shared publications - Felipe Marcelo Galleguillos-Madrid
Centro de Desarrollo Energético Antofagasta, Universidad de Antofagasta, Antofagasta 1240000, Chile
2 shared publications - Hugo Javier Angulo-Palma
Centro de Investigaciones del Níquel "Alberto Fernández Montes de Oca" (CEDINIQ), Moa, Holguín, Cuba + Departamento de Metalurgia Química, Universidad de Moa, Holguín, Cuba
2 shared publications - Norman Toro
Faculty of Engineering and Architecture, Universidad Arturo Prat, Avenida Arturo Prat 2120, Iquique 1110939, Chile
2 shared publications - Ángel Legrá Legrá
Centro de Investigaciones del Níquel "Alberto Fernández Montes de Oca2 (CEDINIQ), Moa, Holguín, Cuba
2 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Hemijska industrija
- Vol. 79 (2) , 69-77
Kinetic behaviour of the roasting/selective reduction process with the use of a mixture of bituminous coal and fuel oil as the additive
Lateritic ore is currently the main raw material that allows extraction of Ni by the Caron process. To date, the kinetic behaviour of the roasting/selective reduction process of lateritic nickeli-ferous ores on a pilot scale is largely unknown. In the present study, the kinetic behaviour, the controlling stage and the mechanisms that describe this process with the use of a mixture of 2 wt.% bituminous coal and 1.25 wt.% fuel oil as a reducing additive were determined during the evaluation of the high and low thermal profiles, respectively. The phases of the reduced/le-ached minerals and the fed ore were analysed by X-ray powder diffraction. It was observed that the mixture used as a reducing additive guarantees an adequate transformation in both thermal profiles; the relationship between the residual Ni and residence time is described by a first-order reaction with the determination coefficients greater than 0.949. Although the influence of post-combustion air is not analysed, the controlling stage was diffusion through the ash layer with an activation energy of 14.4060 kJ mol-1. Thus, the most precise combination to describe the process is diffusion through the ash layer and the growth of the nuclei.
- 1 January 2025
- Published by National Library of Serbia in Hemijska industrija
- Vol. 79 (2) , 69-77
Open AccessKinetic behaviour of the roasting/selective reduction process with the use of a mixture of bituminous coal and fuel oil as the additive
Lateritic ore is currently the main raw material that allows extraction of Ni by the Caron process. To date, the kinetic behaviour of the roasting/selective reduction process of lateritic nickeli-ferous ores on a pilot scale is largely unknown. In the present study, the kinetic behaviour, the controlling stage and the mechanisms that describe this process with the use of a mixture of 2 wt.% bituminous coal and 1.25 wt.% fuel oil as a reducing additive were determined during the evaluation of the high and low thermal profiles, respectively. The phases of the reduced/le-ached minerals and the fed ore were analysed by X-ray powder diffraction. It was observed that the mixture used as a reducing additive guarantees an adequate transformation in both thermal profiles; the relationship between the residual Ni and residence time is described by a first-order reaction with the determination coefficients greater than 0.949. Although the influence of post-combustion air is not analysed, the controlling stage was diffusion through the ash layer with an activation energy of 14.4060 kJ mol-1. Thus, the most precise combination to describe the process is diffusion through the ash layer and the growth of the nuclei.
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Hemijska industrija
- Vol. 78 (1) , 17-27
Use of a mixture of coal and oil as an additive for selective reduction of lateritic ore by the Caron process
Lateritic ores constitute the main source of raw material for extraction of Ni and Co by the Caron process. Consumption of oil in the reduction furnace is one of the key indicators if the metallurgical process is economical. To date it has not been possible to replace the additive fuel oil that is used at commercial scales, therefore, the aim of this study was to partially replace the oil with bituminous coal on a pilot scale by using a mixture of 2 % coal and 1.25 % oil as the reducer additive. Phases of the reduced/leached ores were analyzed by powder X-ray diffraction, while the metallic state of the ore was determined by leaching the reacted samples with a bromine-ethanol solution followed by the atomic absorption spectrometry analysis. Extractions of Ni and Co were confirmed by leaching the reduced ore with ammoniacal-ammonium carbonate solutions. It was observed that the mixture used as a reducer additive can replace the fuel oil since it allows the adequate transformation of the main mineralogical phases of the laterite ore during the reduction process and the average extraction yields of Ni and Co for ~3 and ~8 %, respectively. Although the effect of bituminous coal particle size in the process was not analyzed, the reducing mixture ensured that the Caron process was more efficient.
- 1 January 2024
- Published by National Library of Serbia in Hemijska industrija
- Vol. 78 (1) , 17-27
Open AccessUse of a mixture of coal and oil as an additive for selective reduction of lateritic ore by the Caron process
Lateritic ores constitute the main source of raw material for extraction of Ni and Co by the Caron process. Consumption of oil in the reduction furnace is one of the key indicators if the metallurgical process is economical. To date it has not been possible to replace the additive fuel oil that is used at commercial scales, therefore, the aim of this study was to partially replace the oil with bituminous coal on a pilot scale by using a mixture of 2 % coal and 1.25 % oil as the reducer additive. Phases of the reduced/leached ores were analyzed by powder X-ray diffraction, while the metallic state of the ore was determined by leaching the reacted samples with a bromine-ethanol solution followed by the atomic absorption spectrometry analysis. Extractions of Ni and Co were confirmed by leaching the reduced ore with ammoniacal-ammonium carbonate solutions. It was observed that the mixture used as a reducer additive can replace the fuel oil since it allows the adequate transformation of the main mineralogical phases of the laterite ore during the reduction process and the average extraction yields of Ni and Co for ~3 and ~8 %, respectively. Although the effect of bituminous coal particle size in the process was not analyzed, the reducing mixture ensured that the Caron process was more efficient.