Aya Benhemou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aya Benhemou has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Adrien Badel
Laboratoire SYMME, Université Savoie Mont Blanc, 74940 Annecy, France
4 shared publications - Adrien Morel
SYMME Laboratory, Savoie Mont Blanc University, France
4 shared publications - David Gibus
SYMME, Université Savoie Mont-Blanc, Annecy, France
4 shared publications - Camille Saint-Martin
SYMME, University Savoie Mont-Blanc, F-74000 Annecy, France
3 shared publications - Ludovic Charleux
Univ. Savoie Mont-Blanc EA 4144 SYMME F-74940 Annecy-le-Vieux France
3 shared publications - Emile Roux
Université Savoie Mont Blanc, SYMME
2 shared publications
Latest Publications
- 28 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (4) , 045033
Predictive lumped model for a tunable bistable piezoelectric energy harvester architecture
In this article, we propose the modelling of a tunable bistable piezoelectric energy harvester (or BPEH) architecture. The latter is a type of ambient energy converter that continues to gain attention due to their wideband frequency response. As the non-linear dynamics of BPEHs imply significant modeling complexity, dynamic lumped models are necessary to predict BPEHs’ dynamic response and should fit the type of architecture studied. The BPEH architecture of interest uses post-buckled beams to create bistability and an amplified piezoelectric actuator (or APA) to convert the ambient vibrations. To date, no dynamic lumped models have been found in existing literature that account for both the electromechanical conversion and the dynamic behavior of buckled beams, with a specific focus on their axial and bending stiffness, for this BPEH architecture. Additionally, the proposed BPEH architecture offers buckling level tunability, which is achieved using an additional APA. Hence, the aim of this paper is to propose a new lumped model for a BPEH architecture that considers the effect of the post-buckled beams’ stiffness and of the additional APA through an elasticity factor κ ― . This lumped model is established using Euler Lagrange equations and is experimentally validated on a tunable BPEH prototype. This validation shows an average relative error below 6% between the model predictions and experimental dynamic response of the prototype to an ascending frequency sweep, compared to an average relative error that is around 14% for the model proposed in literature. Moreover, numerical simulations using the proposed model lead to the conclusion that there is an optimal elasticity factor κ ― that ensures the maximum power output while maintaining the frequency bandwidth.
- 28 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (4) , 045033
Predictive lumped model for a tunable bistable piezoelectric energy harvester architecture
In this article, we propose the modelling of a tunable bistable piezoelectric energy harvester (or BPEH) architecture. The latter is a type of ambient energy converter that continues to gain attention due to their wideband frequency response. As the non-linear dynamics of BPEHs imply significant modeling complexity, dynamic lumped models are necessary to predict BPEHs’ dynamic response and should fit the type of architecture studied. The BPEH architecture of interest uses post-buckled beams to create bistability and an amplified piezoelectric actuator (or APA) to convert the ambient vibrations. To date, no dynamic lumped models have been found in existing literature that account for both the electromechanical conversion and the dynamic behavior of buckled beams, with a specific focus on their axial and bending stiffness, for this BPEH architecture. Additionally, the proposed BPEH architecture offers buckling level tunability, which is achieved using an additional APA. Hence, the aim of this paper is to propose a new lumped model for a BPEH architecture that considers the effect of the post-buckled beams’ stiffness and of the additional APA through an elasticity factor κ ― . This lumped model is established using Euler Lagrange equations and is experimentally validated on a tunable BPEH prototype. This validation shows an average relative error below 6% between the model predictions and experimental dynamic response of the prototype to an ascending frequency sweep, compared to an average relative error that is around 14% for the model proposed in literature. Moreover, numerical simulations using the proposed model lead to the conclusion that there is an optimal elasticity factor κ ― that ensures the maximum power output while maintaining the frequency bandwidth.
- 7 December 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (1) , 01LT01
Combining orbit jump and potential wells optimizations for nonlinear vibration energy harvesters
Nonlinear vibration energy harvesters (VEHs) are widely used for scavenging vibrational energy due to their broadband behaviors. However, they exhibit multiple orbits of different powers for a given excitation, including low-power orbits that might limit their performance. To address this issue and enhance nonlinear VEHs performance, various studies have defined orbit jump strategies to transition from low-power to high-power orbits. Another way to maximize the power of nonlinear VEHs is to optimize their geometry by finely engineering their potential wells (PWs). In this letter, we propose an orbit jump strategy for bistable VEHs that combines the two latter approaches, i.e. that simultaneously optimizes their PWs while jumping from low-power to high-power orbits. This orbit jump strategy is optimized using a numerical criterion that takes into account the robustness of the jumps and the invested energy. The proposed orbit jump strategy has been experimentally validated for vibration frequencies between 30 and 60 Hz. It is shown that the proposed approach can increase the power by an average of 121 times over the considered frequency range. Compared to traditional orbit jump strategies, the proposed approach, which combines orbit jumping and PWs optimizations, increases by up to three times the harvested power.
- 7 December 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (1) , 01LT01
Combining orbit jump and potential wells optimizations for nonlinear vibration energy harvesters
Nonlinear vibration energy harvesters (VEHs) are widely used for scavenging vibrational energy due to their broadband behaviors. However, they exhibit multiple orbits of different powers for a given excitation, including low-power orbits that might limit their performance. To address this issue and enhance nonlinear VEHs performance, various studies have defined orbit jump strategies to transition from low-power to high-power orbits. Another way to maximize the power of nonlinear VEHs is to optimize their geometry by finely engineering their potential wells (PWs). In this letter, we propose an orbit jump strategy for bistable VEHs that combines the two latter approaches, i.e. that simultaneously optimizes their PWs while jumping from low-power to high-power orbits. This orbit jump strategy is optimized using a numerical criterion that takes into account the robustness of the jumps and the invested energy. The proposed orbit jump strategy has been experimentally validated for vibration frequencies between 30 and 60 Hz. It is shown that the proposed approach can increase the power by an average of 121 times over the considered frequency range. Compared to traditional orbit jump strategies, the proposed approach, which combines orbit jumping and PWs optimizations, increases by up to three times the harvested power.
- 27 November 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (12) , 125025
A comparative analysis of parallel SSHI and SEH for bistable vibration energy harvesters
The present work focuses on ambient vibration energy harvesting. Specifically, this article deals with bistable piezoelectric energy harvesters (PEHs) which exhibits a wider bandwidth than linear oscillators. These complex systems require an energy extraction circuit (EEC) to rectify their voltage to supply power to autonomous sensors. This EEC needs to be optimized in order to increase the harvested power and even the bandwidth of PEHs. Because of the complex dynamics of bistable PEHs, there is a lack of simple and physically-insightful models in the literature that would allow the understanding and optimization of the extraction circuit. To address this issue, the present work derives closed-form models of a bistable PEH coupled to a passive and an active synchronous EEC: respectively the standard energy harvesting (SEH) circuit and the parallel synchronized switch harvesting on inductor (P-SSHI) circuit. Experimental measurements conducted on a custom bistable PEH demonstrate the validity of the proposed models with a relative error lower than 15% on the harvested power and the bandwidth. The proposed models allow to easily understand the influence of the P-SSHI circuit on the dynamics of a bistable PEH. Moreover, a comparison of the performance of the SEH and the P-SSHI circuits, valid for any bistable generator, is proposed. The latter shows that under low electromechanical coupling and low acceleration amplitude the P-SSHI circuit leads to multiply the maximum harvested power up to 4.3 compared to the SEH circuit, and the bandwidth by a factor of 2.3.
- 27 November 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (12) , 125025
A comparative analysis of parallel SSHI and SEH for bistable vibration energy harvesters
The present work focuses on ambient vibration energy harvesting. Specifically, this article deals with bistable piezoelectric energy harvesters (PEHs) which exhibits a wider bandwidth than linear oscillators. These complex systems require an energy extraction circuit (EEC) to rectify their voltage to supply power to autonomous sensors. This EEC needs to be optimized in order to increase the harvested power and even the bandwidth of PEHs. Because of the complex dynamics of bistable PEHs, there is a lack of simple and physically-insightful models in the literature that would allow the understanding and optimization of the extraction circuit. To address this issue, the present work derives closed-form models of a bistable PEH coupled to a passive and an active synchronous EEC: respectively the standard energy harvesting (SEH) circuit and the parallel synchronized switch harvesting on inductor (P-SSHI) circuit. Experimental measurements conducted on a custom bistable PEH demonstrate the validity of the proposed models with a relative error lower than 15% on the harvested power and the bandwidth. The proposed models allow to easily understand the influence of the P-SSHI circuit on the dynamics of a bistable PEH. Moreover, a comparison of the performance of the SEH and the P-SSHI circuits, valid for any bistable generator, is proposed. The latter shows that under low electromechanical coupling and low acceleration amplitude the P-SSHI circuit leads to multiply the maximum harvested power up to 4.3 compared to the SEH circuit, and the bandwidth by a factor of 2.3.
- Open Access
- 5 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 136-140
Design approach for post-buckled beams in bistable piezoelectric energy harvesters
This paper presents a model suited for the design of mechanically bistable beams used in Piezoelectric Energy Harvesters (PEHs). The proposed model accounts for the bending and compression of post-buckled beams used in the PEH. The effect of the beam’s geometry on the generated power and frequency bandwidth is evaluated with a performance criterion. It is concluded that a low beam compression stiffness can have a negative impact on the performance of the PEH and that the bending stiffness solely implies a prestress on the piezoelectric transducer.
- 5 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 136-140
Open AccessDesign approach for post-buckled beams in bistable piezoelectric energy harvesters
This paper presents a model suited for the design of mechanically bistable beams used in Piezoelectric Energy Harvesters (PEHs). The proposed model accounts for the bending and compression of post-buckled beams used in the PEH. The effect of the beam’s geometry on the generated power and frequency bandwidth is evaluated with a performance criterion. It is concluded that a low beam compression stiffness can have a negative impact on the performance of the PEH and that the bending stiffness solely implies a prestress on the piezoelectric transducer.