Jamal AlHourani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jamal AlHourani has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Yury Gogotsi
A.J. Drexel Nanomaterials Institute and Department of Materials Science and Engineering, Drexel University, Philadelphia, USA
5 shared publications - Gary G. Friedman
Department of Electrical and Computer Engineering Drexel University 3141 Chestnut St Philadelphia PA 19104 USA
2 shared publications - Mohammad Hossein Zarifi
University of British Columbia
2 shared publications - Roman Rakhmanov
Department of Electrical and Computer Engineering Drexel University 3141 Chestnut St Philadelphia PA 19104 USA
2 shared publications - Stefano Ippolito
Drexel University
2 shared publications - Zahra Sarpanah Sourkouhi
Faculty of Applied Science The University of British Columbia Kelowna Canada
2 shared publications
Latest Publications
- Open Access
- 24 September 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (39) , 26511-26520
Anomalous Microwave Absorption Hysteresis in Ultrathin MXene Films with Confined Water
MXenes, a family of two-dimensional (2D) transition-metal carbides, nitrides, and carbonitrides, are promising materials for electromagnetic interference (EMI) shielding due to their electronic conductivity, tunable surface functionalization, and adjustable interlayer spacing. In many practical environments, MXene films host water molecules between the carbide or nitride nanosheets. However, the influence of confined water on their microwave absorption remains unclear. Here, we investigate the role of water confinement in governing microwave absorption in Ti3C2Tx MXene films. In situ humidity-dependent measurements reveal that protonated films exhibit a 56% increase in absorption even without measurable changes in interlayer spacing. In contrast, Li+-intercalated films, which undergo interlayer swelling upon water uptake, show a 167% increase in absorption. The observed enhancement in microwave absorption upon water uptake is approximately 4 orders of magnitude larger than what would be expected from the increase in bulk water content alone. These changes indicate that water confined within MXene films produces microwave absorption behavior, unlike that of conventional microwave shielding materials where impedance matching is achieved by varying material thickness. The results clarify the role of confined water in EMI absorption in MXenes and indicate that water confinement can serve as a tunable parameter for engineering high-performance EMI shielding materials.
- 24 September 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (39) , 26511-26520
Open AccessAnomalous Microwave Absorption Hysteresis in Ultrathin MXene Films with Confined Water
MXenes, a family of two-dimensional (2D) transition-metal carbides, nitrides, and carbonitrides, are promising materials for electromagnetic interference (EMI) shielding due to their electronic conductivity, tunable surface functionalization, and adjustable interlayer spacing. In many practical environments, MXene films host water molecules between the carbide or nitride nanosheets. However, the influence of confined water on their microwave absorption remains unclear. Here, we investigate the role of water confinement in governing microwave absorption in Ti3C2Tx MXene films. In situ humidity-dependent measurements reveal that protonated films exhibit a 56% increase in absorption even without measurable changes in interlayer spacing. In contrast, Li+-intercalated films, which undergo interlayer swelling upon water uptake, show a 167% increase in absorption. The observed enhancement in microwave absorption upon water uptake is approximately 4 orders of magnitude larger than what would be expected from the increase in bulk water content alone. These changes indicate that water confined within MXene films produces microwave absorption behavior, unlike that of conventional microwave shielding materials where impedance matching is achieved by varying material thickness. The results clarify the role of confined water in EMI absorption in MXenes and indicate that water confinement can serve as a tunable parameter for engineering high-performance EMI shielding materials.
- Open Access
- 24 January 2026
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (9)
MXene‐Coated 3D Printed Horn Antennas for Ku Frequency Band
Demands for lightweight, scalable, and rapidly fabricated radio‐frequency components are emerging in aerospace and portable wireless communication systems. This work introduces a lightweight, additively manufactured MXene‐coated horn antenna operating in the Ku band (12 to 18 GHz). Aqueous colloidal Ti 3 C 2 T x MXene was applied to form conformal, conductive coatings on polymeric horn antenna surfaces to reduce the fabrication complexities. The performance of the MXene‐based antennas was investigated as a function of 3D‐printed polymer base filaments such as PLA, PET G, PA 6, and PA 12, 3D‐printing methods including FDM and SLS, and concentrations of MXene 32 and 18 mg g −1 . To demonstrate comparable electromagnetic performance, the fabricated MXene antennas were quantitatively compared with a conventional aluminum counterpart at the center frequency. The root‐mean‐square‐error of the average transmission coefficient, , was evaluated, where the difference in results indicates an RMSE below 0.34 dB, accompanied by a gain difference of only 0.2 dB. Furthermore, the correlation coefficient, r , was evaluated to assess the similarity of the responses, yielding values exceeding 0.98 for all tested antennas, confirming the high degree of agreement between the MXene‐based and conventional aluminum antennas.
- 24 January 2026
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (9)
Open AccessMXene‐Coated 3D Printed Horn Antennas for Ku Frequency Band
Demands for lightweight, scalable, and rapidly fabricated radio‐frequency components are emerging in aerospace and portable wireless communication systems. This work introduces a lightweight, additively manufactured MXene‐coated horn antenna operating in the Ku band (12 to 18 GHz). Aqueous colloidal Ti 3 C 2 T x MXene was applied to form conformal, conductive coatings on polymeric horn antenna surfaces to reduce the fabrication complexities. The performance of the MXene‐based antennas was investigated as a function of 3D‐printed polymer base filaments such as PLA, PET G, PA 6, and PA 12, 3D‐printing methods including FDM and SLS, and concentrations of MXene 32 and 18 mg g −1 . To demonstrate comparable electromagnetic performance, the fabricated MXene antennas were quantitatively compared with a conventional aluminum counterpart at the center frequency. The root‐mean‐square‐error of the average transmission coefficient, , was evaluated, where the difference in results indicates an RMSE below 0.34 dB, accompanied by a gain difference of only 0.2 dB. Furthermore, the correlation coefficient, r , was evaluated to assess the similarity of the responses, yielding values exceeding 0.98 for all tested antennas, confirming the high degree of agreement between the MXene‐based and conventional aluminum antennas.
Patterning MXene RFID Antennas via Surface Hydrophobicity Modulation
MXenes are an emerging class of 2D transition metal carbides and nitrides, known for their mechanical, chemical, and electrical properties, which make them suitable for electromagnetic applications such as antennas and radio frequency identification (RFID) devices. This research demonstrates that MXene‐based RFID antennas can be patterned by modifying the hydrophobicity of a hydrophilic paper substrate. A Ti3C2Tx MXene colloid with a concentration of 32 mg g−1 with a conductivity of (≈10 000 S cm−1) is used to fabricate conductive traces of RFID antennas through dip‐coating, using a superhydrophobic layer patterning technique. Ink spreading is minimized by controlling the water repellency of the surfaces and taking advantage of the inherent hydrophilicity of MXene, resulting in improved pattern fidelity. The versatility of the proposed patterning method is demonstrated through the fabrication of three different RFID antenna tags, including dipole, meander, and T‐matched antennas, designed to operate at ultrahigh frequency (UHF) (800–920 MHz). The method also enabled impedance matching for dipole and meander‐shaped RFIDs to 50 Ω, achieving ≈ 97% efficiency compared to copper‐based counterparts fabricated using subtractive methods. This approach enables well‐defined, self‐confined deposition and offers a scalable process for MXene conductive traces and microstrip lines patterning.
Patterning MXene RFID Antennas via Surface Hydrophobicity Modulation
MXenes are an emerging class of 2D transition metal carbides and nitrides, known for their mechanical, chemical, and electrical properties, which make them suitable for electromagnetic applications such as antennas and radio frequency identification (RFID) devices. This research demonstrates that MXene‐based RFID antennas can be patterned by modifying the hydrophobicity of a hydrophilic paper substrate. A Ti3C2Tx MXene colloid with a concentration of 32 mg g−1 with a conductivity of (≈10 000 S cm−1) is used to fabricate conductive traces of RFID antennas through dip‐coating, using a superhydrophobic layer patterning technique. Ink spreading is minimized by controlling the water repellency of the surfaces and taking advantage of the inherent hydrophilicity of MXene, resulting in improved pattern fidelity. The versatility of the proposed patterning method is demonstrated through the fabrication of three different RFID antenna tags, including dipole, meander, and T‐matched antennas, designed to operate at ultrahigh frequency (UHF) (800–920 MHz). The method also enabled impedance matching for dipole and meander‐shaped RFIDs to 50 Ω, achieving ≈ 97% efficiency compared to copper‐based counterparts fabricated using subtractive methods. This approach enables well‐defined, self‐confined deposition and offers a scalable process for MXene conductive traces and microstrip lines patterning.
- 9 September 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (18)
Influence of MXene Interlayer Spacing on the Interaction with Microwave Radiation
The origin of MXene's excellent electromagnetic shielding performance is not fully understood. MXene films, despite being inhomogeneous at the nanometer scale, are often treated as if they are compared to bulk conductors. It is reasonable to wonder if the treatment of MXene as a homogeneous material remains valid at very small film thickness and if it depends on the interlayer spacing. The goal of the present work is to test if the homogeneous material model is applicable to nanometer‐thin Ti 3 C 2 T x MXene films and, if so, to investigate how the model parameters may depend on variations in MXene interlayer spacings. MXene films containing flakes with interlayer spacing between 1.9 and 5.5 Å have been prepared using various intercalating agents. It is shown that modeling the films as being homogeneous agrees with experimental tests in the microwave frequency range. Microwave conductivity and dielectric constant parameters are estimated for the homogeneous film model by fitting measured results. The direct current (DC) conductivity matches the estimated microwave conductivity on the order of magnitude. A highly effective dielectric constant provides a good fit for the lower conductivity MXene films. Optical absorption agrees with the homogeneous material model of thin films as well.
- 9 September 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (18)
Influence of MXene Interlayer Spacing on the Interaction with Microwave Radiation
The origin of MXene's excellent electromagnetic shielding performance is not fully understood. MXene films, despite being inhomogeneous at the nanometer scale, are often treated as if they are compared to bulk conductors. It is reasonable to wonder if the treatment of MXene as a homogeneous material remains valid at very small film thickness and if it depends on the interlayer spacing. The goal of the present work is to test if the homogeneous material model is applicable to nanometer‐thin Ti 3 C 2 T x MXene films and, if so, to investigate how the model parameters may depend on variations in MXene interlayer spacings. MXene films containing flakes with interlayer spacing between 1.9 and 5.5 Å have been prepared using various intercalating agents. It is shown that modeling the films as being homogeneous agrees with experimental tests in the microwave frequency range. Microwave conductivity and dielectric constant parameters are estimated for the homogeneous film model by fitting measured results. The direct current (DC) conductivity matches the estimated microwave conductivity on the order of magnitude. A highly effective dielectric constant provides a good fit for the lower conductivity MXene films. Optical absorption agrees with the homogeneous material model of thin films as well.
- Open Access
- 13 November 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (20)
Ultrathin MXene film interaction with electromagnetic radiation in the microwave range
The quick progress in communication technologies demands superior electromagnetic interference (EMI) shielding materials. However, achieving a high shielding effectiveness (SE) with thin films, which is needed for microscale, flexible, and wearable devices, through absorption of EM radiation remains a challenge. 2D titanium carbide MXene, Ti3C2Tx, has been shown to efficiently reflect electromagnetic waves. In this paper, we investigated the electromagnetic shielding of ultrathin printed Ti3C2Tx films and recorded absorption up to 50% for 4 nm-thick films. This behavior is explained by impedance matching. Analysis of the sheet impedance in the X-band frequency range allows us to correlate the EMI shielding mechanism with the electrical conductivity measured within the same range. The average bulk in-plane conductivity for 4 to 40 nm-thick films reaches 106 S/m, while the average relaxation time is estimated at around 2.3 ps. Our figures of merit are similar to those reported for ultrathin metal films, such as gold, showing that an abundant MXene material can replace noble metals. We demonstrate that the MXene conductivity mechanism does not change from direct current to THz. The conventional method of reporting EMI SE is correlated with absolute values of transmitted, reflected, and absorbed power, which allows us to interpret previous results on MXene EMI shielding. Considering the easy deposition of thin MXenes films from solution onto a variety of surfaces, our findings offer an attractive alternative for shielding microscale devices and personal electronics.
- 13 November 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (20)
Open AccessUltrathin MXene film interaction with electromagnetic radiation in the microwave range
The quick progress in communication technologies demands superior electromagnetic interference (EMI) shielding materials. However, achieving a high shielding effectiveness (SE) with thin films, which is needed for microscale, flexible, and wearable devices, through absorption of EM radiation remains a challenge. 2D titanium carbide MXene, Ti3C2Tx, has been shown to efficiently reflect electromagnetic waves. In this paper, we investigated the electromagnetic shielding of ultrathin printed Ti3C2Tx films and recorded absorption up to 50% for 4 nm-thick films. This behavior is explained by impedance matching. Analysis of the sheet impedance in the X-band frequency range allows us to correlate the EMI shielding mechanism with the electrical conductivity measured within the same range. The average bulk in-plane conductivity for 4 to 40 nm-thick films reaches 106 S/m, while the average relaxation time is estimated at around 2.3 ps. Our figures of merit are similar to those reported for ultrathin metal films, such as gold, showing that an abundant MXene material can replace noble metals. We demonstrate that the MXene conductivity mechanism does not change from direct current to THz. The conventional method of reporting EMI SE is correlated with absolute values of transmitted, reflected, and absorbed power, which allows us to interpret previous results on MXene EMI shielding. Considering the easy deposition of thin MXenes films from solution onto a variety of surfaces, our findings offer an attractive alternative for shielding microscale devices and personal electronics.