Tingting Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tingting Wu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Chao Zhang
Nanjing University of Aeronautics and Astronautics
1 shared publication - Jinhao Qiu
Nanjing University of Aeronautics and Astronautics
1 shared publication - Nan-Xing Shi
Key Laboratory of Unsteady Aerodynamics and Flow Control, Ministry of Industry and Information Technology, Nanjing University of Aeronautics and Astronautics, Yudao Street 29, Nanjing 210016, China
1 shared publication - Shuai Deng
Key Laboratory of Unsteady Aerodynamics and Flow Control, Ministry of Industry and Information Technology, Nanjing University of Aeronautics and Astronautics, Yudao Street 29, Nanjing 210016, China
1 shared publication - Yi Wang
Key Laboratory of Unsteady Aerodynamics and Flow Control, Ministry of Industry and Information Technology, Nanjing University of Aeronautics and Astronautics, Yudao Street 29, Nanjing 210016, China
1 shared publication - Yuhang Zhou
High Speed Aerodynamics Institute, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication
Latest Publications
- Open Access
- 1 September 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3326 (1)
Identification of surface defects in thermal protection system under aerodynamic heating
The thermal protection system (TPS) is vital to hypersonic flight safety. To monitor possible surface impact defects for TPS, a robust and efficient approach for surface defect identification is proposed in this paper. Surface aerodynamic heating distribution caused by the defect is considered, which is complex during actual flights. First, the aerodynamic heating distribution is investigated, and the influence of different defect sizes on the heating distribution is analyzed. Next, the Levenberg‑Marquardt (LM) algorithm is employed to identify surface defects using temperature measurements acquired from the accessible surface. To improve computational efficiency, an approximate model is established for solving the direct problems during the identification process. Finally, numerical examples are provided to verify the effectiveness and robustness of the present method.
- 1 September 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3326 (1)
Open AccessIdentification of surface defects in thermal protection system under aerodynamic heating
The thermal protection system (TPS) is vital to hypersonic flight safety. To monitor possible surface impact defects for TPS, a robust and efficient approach for surface defect identification is proposed in this paper. Surface aerodynamic heating distribution caused by the defect is considered, which is complex during actual flights. First, the aerodynamic heating distribution is investigated, and the influence of different defect sizes on the heating distribution is analyzed. Next, the Levenberg‑Marquardt (LM) algorithm is employed to identify surface defects using temperature measurements acquired from the accessible surface. To improve computational efficiency, an approximate model is established for solving the direct problems during the identification process. Finally, numerical examples are provided to verify the effectiveness and robustness of the present method.
- Open Access
An Optimized Pressure-Based Method for Thrust Vectoring Angle Estimation
This research developed a pressure-based thrust vectoring angle estimation method for fluidic thrust vectoring nozzles. This method can accurately estimate the real-time in-flight thrust vectoring angle using only wall pressure information on the inner surface of the nozzle. We proposed an algorithm to calculate the thrust vectoring angle from the wall pressure inside the nozzle. Non-dominated sorting genetic algorithm II was applied to find the optimal sensor arrays and reduce the wall pressure sensor quantity. Synchronous force and wall pressure measurement experiments were carried out to verify the accuracy and real-time response of the pressure-based thrust vectoring angle estimation method. The results showed that accurate estimation of the thrust vectoring angle can be achieved with a minimum of three pressure sensors. The pressure-based thrust vectoring angle estimation method proposed in this study has a good prospect for engineering applications; it is capable of accurate real-time in-flight monitoring of the thrust vectoring angle. This method is important and indispensable for the closed-loop feedback control and aircraft attitude control of fluidic thrust vectoring control technology.
Open AccessAn Optimized Pressure-Based Method for Thrust Vectoring Angle Estimation
This research developed a pressure-based thrust vectoring angle estimation method for fluidic thrust vectoring nozzles. This method can accurately estimate the real-time in-flight thrust vectoring angle using only wall pressure information on the inner surface of the nozzle. We proposed an algorithm to calculate the thrust vectoring angle from the wall pressure inside the nozzle. Non-dominated sorting genetic algorithm II was applied to find the optimal sensor arrays and reduce the wall pressure sensor quantity. Synchronous force and wall pressure measurement experiments were carried out to verify the accuracy and real-time response of the pressure-based thrust vectoring angle estimation method. The results showed that accurate estimation of the thrust vectoring angle can be achieved with a minimum of three pressure sensors. The pressure-based thrust vectoring angle estimation method proposed in this study has a good prospect for engineering applications; it is capable of accurate real-time in-flight monitoring of the thrust vectoring angle. This method is important and indispensable for the closed-loop feedback control and aircraft attitude control of fluidic thrust vectoring control technology.