Rajeev Kapoor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rajeev Kapoor has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
Apu Sarkar
Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai, India
4 shared publications- A. Kedharnath
Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai, India
3 shared publications - Apu Sarkar
Bhabha Atomic Research Centre
3 shared publications G. Bharat Reddy
Homi Bhabha Natl Inst, Div Engn Sci, Mumbai 400094, India
3 shared publications- Indradev Samajdar
IIT Bombay
3 shared publications Komal Kapoor
Nuclear Fuel Complex
3 shared publications
Latest Publications
- 19 October 2026
- Published by SAGE Publications in International Materials Reviews
Processing-structure-property landscape in dilute zirconium alloys for nuclear energy applications
The need for sustainable energy has become paramount in today's context, owing to the alarming rise in global greenhouse gas emissions and the consequent adverse impact on climate change. Among these energy resources, nuclear energy holds a special place in fulfilling global commitments and thus warrants a special interest. Zirconium alloys are the preferred in-core structural materials in water-cooled reactors, the most widely used reactor configuration. Nevertheless, further research is needed to improve the understanding of how structural materials influence the long-term and reliable performance of nuclear reactors. Material performance and in-reactor degradation mechanisms are largely governed by various metallurgical factors that can be engineered during thermo-mechanical processing (TMP). The structural evolution at each TMP step governs that of the following steps, so that the final microstructure and properties are a cumulative outcome of the processing steps. Despite the criticality, the interlinkage among processing, microstructure, texture, and properties has not been comprehensively reviewed and remains scattered in the literature. This article provides an in-depth, state-of-the-art review of the interlinkages between processing, microstructure, and properties in zirconium alloys, elucidating the foundation of physical metallurgy, the critical role of TMP in microstructure and texture control, and the impact of microstructure and texture on the key properties of zirconium alloys. In summary, by focusing on the complex interdependence of processing, microstructure, and properties in zirconium alloys, this review emphasises their importance in advancing nuclear reactor technology and highlights emerging opportunities for innovation. Future research integrating novel alloy compositions, advanced characterisation techniques, and predictive modelling will be essential for improving the durability, safety, and reliability of zirconium-based structural materials, thereby supporting a more sustainable nuclear energy ecosystem.
- 19 October 2026
- Published by SAGE Publications in International Materials Reviews
Processing-structure-property landscape in dilute zirconium alloys for nuclear energy applications
The need for sustainable energy has become paramount in today's context, owing to the alarming rise in global greenhouse gas emissions and the consequent adverse impact on climate change. Among these energy resources, nuclear energy holds a special place in fulfilling global commitments and thus warrants a special interest. Zirconium alloys are the preferred in-core structural materials in water-cooled reactors, the most widely used reactor configuration. Nevertheless, further research is needed to improve the understanding of how structural materials influence the long-term and reliable performance of nuclear reactors. Material performance and in-reactor degradation mechanisms are largely governed by various metallurgical factors that can be engineered during thermo-mechanical processing (TMP). The structural evolution at each TMP step governs that of the following steps, so that the final microstructure and properties are a cumulative outcome of the processing steps. Despite the criticality, the interlinkage among processing, microstructure, texture, and properties has not been comprehensively reviewed and remains scattered in the literature. This article provides an in-depth, state-of-the-art review of the interlinkages between processing, microstructure, and properties in zirconium alloys, elucidating the foundation of physical metallurgy, the critical role of TMP in microstructure and texture control, and the impact of microstructure and texture on the key properties of zirconium alloys. In summary, by focusing on the complex interdependence of processing, microstructure, and properties in zirconium alloys, this review emphasises their importance in advancing nuclear reactor technology and highlights emerging opportunities for innovation. Future research integrating novel alloy compositions, advanced characterisation techniques, and predictive modelling will be essential for improving the durability, safety, and reliability of zirconium-based structural materials, thereby supporting a more sustainable nuclear energy ecosystem.
- 3 December 2025
- Published by Elsevier in International Journal of Plasticity
- Vol. 196
Growth selection of deformation twins in hexagonal titanium
- 3 December 2025
- Published by Elsevier in International Journal of Plasticity
- Vol. 196
Growth selection of deformation twins in hexagonal titanium
- 26 August 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 945
Influence of hot deformation processing on microstructure, texture, and properties of Zircaloy-4
- 26 August 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 945
Influence of hot deformation processing on microstructure, texture, and properties of Zircaloy-4
- Open Access
- 28 January 2025
- Published by Springer Nature in Metals and Materials International
- Vol. 31 (9) , 2541-2550
Microstructural and Strength Changes During Multi-Axial Forging of Ta-10 wt% W and its Comparison with Ta
The study aims to bring out the effect of microstructural modification and W addition in TaW on the strength as these alloys find applications in ballistics, high temperature and corrosive environments. Coarse-grained tantalum-10 wt% tungsten (Ta-10 W) was multi-axially forged (MAF) to 3, 6, and 9 passes corresponding to equivalent strains of 2.4, 4.8 and 7.2, respectively. The MAF Ta-10 W samples were characterized for their microstructural and mechanical properties. The average grain size decreased from 20 μm in the starting material to 3 μm after 3 passes and to 0.38 μm after 9 passes. The fraction of high angle grain boundaries ( $$\:{f}_{hagb}$$ ) increased from 0.26 (3 passes) to 0.56 (9 passes) and the fraction of recrystallized grains ( $$\:{f}_{recry}$$ ) increased from 0.31 (3 passes) to 0.92 (9 passes). The yield stress increased from 964 MPa after 3 passes to 1202 MPa after 9 passes. It was found that the contribution from GBs as compared to that from dislocations was lower after 3 passes than after 9 passes. The addition of tungsten to tantalum increased the flow locus during MAF and yield stress of MAF samples to almost double as compared to Ta. As compared to MAF Ta, MAF Ta-10 W showed finer grains, higher $$\:{f}_{hagb}$$ , and higher $$\:{f}_{recry}$$ . Graphical Abstract- 28 January 2025
- Published by Springer Nature in Metals and Materials International
- Vol. 31 (9) , 2541-2550
Open AccessMicrostructural and Strength Changes During Multi-Axial Forging of Ta-10 wt% W and its Comparison with Ta
The study aims to bring out the effect of microstructural modification and W addition in TaW on the strength as these alloys find applications in ballistics, high temperature and corrosive environments. Coarse-grained tantalum-10 wt% tungsten (Ta-10 W) was multi-axially forged (MAF) to 3, 6, and 9 passes corresponding to equivalent strains of 2.4, 4.8 and 7.2, respectively. The MAF Ta-10 W samples were characterized for their microstructural and mechanical properties. The average grain size decreased from 20 μm in the starting material to 3 μm after 3 passes and to 0.38 μm after 9 passes. The fraction of high angle grain boundaries ( $$\:{f}_{hagb}$$ ) increased from 0.26 (3 passes) to 0.56 (9 passes) and the fraction of recrystallized grains ( $$\:{f}_{recry}$$ ) increased from 0.31 (3 passes) to 0.92 (9 passes). The yield stress increased from 964 MPa after 3 passes to 1202 MPa after 9 passes. It was found that the contribution from GBs as compared to that from dislocations was lower after 3 passes than after 9 passes. The addition of tungsten to tantalum increased the flow locus during MAF and yield stress of MAF samples to almost double as compared to Ta. As compared to MAF Ta, MAF Ta-10 W showed finer grains, higher $$\:{f}_{hagb}$$ , and higher $$\:{f}_{recry}$$ . Graphical Abstract - Open Access
- 19 December 2024
- Published by Springer Nature in Tungsten
- Vol. 7 (2) , 327-336
Understanding dislocation velocity in TaW using explainable machine learning
The present work calculated the velocity of edge dislocations in the Ta–W system using molecular dynamics (MD) simulations and through machine learning (ML), identified the key parameters influencing the velocity. To achieve this, MD simulations were conducted at various values of the extrinsic parameters—temperatures and applied stresses ( $${\tau }_{\text{app}}$$ ), and the intrinsic variables—slip systems and alloying contents of tungsten in tantalum. Configurations containing edge dislocations on {110}/{112}/{123} planes were employed, and dislocation velocities were subsequently estimated. The MD results were processed using ML models, specifically extreme gradient boosting and SHapley Additive exPlanations (SHAP). SHAP analysis identified $${\tau }_{\text{app}}$$ as the most influencing parameter affecting velocity, followed by slip plane, temperature, and W addition. SHAP estimated the base velocity value ( $${v}_{\text{b}}$$ ) to be 1376 m·s-1. $${v}_{\text{b}}$$ was calculated by training SHAP on a parameter-less model. $${v}_{\text{b}}$$ could be increased by applying $${\tau }_{\text{app}}$$ of at least 1 GPa, through slipping on the {112} and {123} planes, at temperatures of 0 and 300 K, and in configurations with 0 wt.% and 5 wt.% W. The importance of $${v}_{\text{b}}$$ on deformation was established.- 19 December 2024
- Published by Springer Nature in Tungsten
- Vol. 7 (2) , 327-336
Open AccessUnderstanding dislocation velocity in TaW using explainable machine learning
The present work calculated the velocity of edge dislocations in the Ta–W system using molecular dynamics (MD) simulations and through machine learning (ML), identified the key parameters influencing the velocity. To achieve this, MD simulations were conducted at various values of the extrinsic parameters—temperatures and applied stresses ( $${\tau }_{\text{app}}$$ ), and the intrinsic variables—slip systems and alloying contents of tungsten in tantalum. Configurations containing edge dislocations on {110}/{112}/{123} planes were employed, and dislocation velocities were subsequently estimated. The MD results were processed using ML models, specifically extreme gradient boosting and SHapley Additive exPlanations (SHAP). SHAP analysis identified $${\tau }_{\text{app}}$$ as the most influencing parameter affecting velocity, followed by slip plane, temperature, and W addition. SHAP estimated the base velocity value ( $${v}_{\text{b}}$$ ) to be 1376 m·s-1. $${v}_{\text{b}}$$ was calculated by training SHAP on a parameter-less model. $${v}_{\text{b}}$$ could be increased by applying $${\tau }_{\text{app}}$$ of at least 1 GPa, through slipping on the {112} and {123} planes, at temperatures of 0 and 300 K, and in configurations with 0 wt.% and 5 wt.% W. The importance of $${v}_{\text{b}}$$ on deformation was established. - 26 November 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 921
Overcoming the strength-ductility trade-off in zirconium using twin boundary engineering
- 26 November 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 921
Overcoming the strength-ductility trade-off in zirconium using twin boundary engineering
- 30 October 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 604
Role of severe plastic deformation on mechanical behavior of irradiated materials: A case study with Nb-1Zr alloy
- 30 October 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 604
Role of severe plastic deformation on mechanical behavior of irradiated materials: A case study with Nb-1Zr alloy
- 11 May 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 902
Grain boundary localized damage in hexagonal titanium
- 11 May 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 902
Grain boundary localized damage in hexagonal titanium