Ersoy Kabadayı
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ersoy Kabadayı has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Aytuğ Kumandaş
ONDOKUZ MAYIS ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, İNŞAAT MÜHENDİSLİĞİ BÖLÜMÜ
3 shared publications - Erman Çavdar
Karadeniz Technical University
2 shared publications - Neslihan Şahan
Karadeniz Teknik Üniversitesi
2 shared publications - Şeref Oruç
Karadeniz Technical University
2 shared publications - Baha Vural Kök
Firat Universitesi
1 shared publication Erman Çavdar
Ph.D. Candidate and Research Assistant, Dept. of Civil Engineering, Karadeniz Technical Univ., Trabzon 61080, Türkiye
1 shared publication
Latest Publications
- Open Access
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 1-18
Investigation of Rheological and Physical Properties of SBS and WCO Composite Modified Bitumen
Nowadays, the use of waste materials in various industries is becoming widespread in order to promote waste recycling. Thus, scientists are researching the use of waste materials in bitumen modification. In this study, it was aimed to investigate the effect of waste cooking oil (WCO) on the physical and rheological properties of unaged Styrene-Butadiene-Styrene modified bitumen (SBSMB) by adding WCO at different ratios (1, 3, 5, 7, and 9%) to SBS modified bitumen. Accordingly, rotational viscosity (RV) tests and rheological tests with dynamic shear rheometer (DSR) based on the determination of complex shear modulus (|G*|) and phase angle (δ) were conducted along with the traditional bitumen tests. As a result of the experimental study, it was observed that adding WCO increased the workability and fatigue resistance of SBSMB, however, decreased its rutting resistance. Therefore, the mixing and compaction temperatures of SBSMB can be decreased by adding low amounts of WCO without excessive performance loss. Thus, during the construction of asphalt pavements, environmental damage can be reduced by utilizing waste materials and reducing CO2 emissions.
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 1-18
Open AccessInvestigation of Rheological and Physical Properties of SBS and WCO Composite Modified Bitumen
Nowadays, the use of waste materials in various industries is becoming widespread in order to promote waste recycling. Thus, scientists are researching the use of waste materials in bitumen modification. In this study, it was aimed to investigate the effect of waste cooking oil (WCO) on the physical and rheological properties of unaged Styrene-Butadiene-Styrene modified bitumen (SBSMB) by adding WCO at different ratios (1, 3, 5, 7, and 9%) to SBS modified bitumen. Accordingly, rotational viscosity (RV) tests and rheological tests with dynamic shear rheometer (DSR) based on the determination of complex shear modulus (|G*|) and phase angle (δ) were conducted along with the traditional bitumen tests. As a result of the experimental study, it was observed that adding WCO increased the workability and fatigue resistance of SBSMB, however, decreased its rutting resistance. Therefore, the mixing and compaction temperatures of SBSMB can be decreased by adding low amounts of WCO without excessive performance loss. Thus, during the construction of asphalt pavements, environmental damage can be reduced by utilizing waste materials and reducing CO2 emissions.
- Open Access
- 16 April 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (3) , 1493-1510
Investigation of the Effect of Boron Oxide and Beeswax on Workability and High-Temperature Performance of Bitumen
In recent years, various studies have shown that boron-containing additives improve the rutting performance of the bituminous pavements. However, in these studies, it was stated that these additives would decrease the workability of the bitumen and increase energy required for the construction of the pavement. On the other hand, it has been shown in many studies that waxes increase the workability of the bitumen. In this study, it was aimed to obtain bitumen with high rutting resistance and workability by adding boron oxide (BO) and beeswax (BW) to bitumen. Therefore, modified bitumen was produced by adding BO and BW at different ratios to a 50/70 penetration grade base bitumen. Then, the chemical, physical, and rheological properties of modified bitumen samples were investigated by various experiments. As a result, it has been observed that BO increases the high-temperature performance and viscosity of bitumen; on the other hand, BW decreases rutting resistance and viscosity. When BO and BW were added together to the bitumen, the negative impact of BO on workability and the negative impact of BW on high temperature performance were significantly eliminated. Especially, in 1BO + 1BW and 3BO + 3BW bitumens, the high-temperature performance of the bitumen improved without decreasing the workability.
- 16 April 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (3) , 1493-1510
Open AccessInvestigation of the Effect of Boron Oxide and Beeswax on Workability and High-Temperature Performance of Bitumen
In recent years, various studies have shown that boron-containing additives improve the rutting performance of the bituminous pavements. However, in these studies, it was stated that these additives would decrease the workability of the bitumen and increase energy required for the construction of the pavement. On the other hand, it has been shown in many studies that waxes increase the workability of the bitumen. In this study, it was aimed to obtain bitumen with high rutting resistance and workability by adding boron oxide (BO) and beeswax (BW) to bitumen. Therefore, modified bitumen was produced by adding BO and BW at different ratios to a 50/70 penetration grade base bitumen. Then, the chemical, physical, and rheological properties of modified bitumen samples were investigated by various experiments. As a result, it has been observed that BO increases the high-temperature performance and viscosity of bitumen; on the other hand, BW decreases rutting resistance and viscosity. When BO and BW were added together to the bitumen, the negative impact of BO on workability and the negative impact of BW on high temperature performance were significantly eliminated. Especially, in 1BO + 1BW and 3BO + 3BW bitumens, the high-temperature performance of the bitumen improved without decreasing the workability.