Şeref Oruç
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Şeref Oruç has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Aytuğ Kumandaş
ONDOKUZ MAYIS ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, İNŞAAT MÜHENDİSLİĞİ BÖLÜMÜ
5 shared publications - Neslihan Şahan
Karadeniz Teknik Üniversitesi
5 shared publications - Erman Çavdar
Karadeniz Technical University
4 shared publications - Baha Vural Kök
Firat Universitesi
2 shared publications - Erhan Burak Pancar
Ondokuz Mayıs University
2 shared publications - Ersoy Kabadayı
Giresun Üniversitesi
2 shared publications
Latest Publications
- Open Access
- 25 August 2026
- Published by Springer Nature in Scientific Reports
Effect of re-refined engine oil bottoms on rutting and fatigue performance of EVA-modified bitumen
- 25 August 2026
- Published by Springer Nature in Scientific Reports
Open AccessEffect of re-refined engine oil bottoms on rutting and fatigue performance of EVA-modified bitumen
- 3 April 2025
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 27 (1) , 1-58
Biopolymers as bitumen additives: a systematic quantitative literature review
- 3 April 2025
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 27 (1) , 1-58
Biopolymers as bitumen additives: a systematic quantitative literature review
- Open Access
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 1-18
Investigation of Rheological and Physical Properties of SBS and WCO Composite Modified Bitumen
Nowadays, the use of waste materials in various industries is becoming widespread in order to promote waste recycling. Thus, scientists are researching the use of waste materials in bitumen modification. In this study, it was aimed to investigate the effect of waste cooking oil (WCO) on the physical and rheological properties of unaged Styrene-Butadiene-Styrene modified bitumen (SBSMB) by adding WCO at different ratios (1, 3, 5, 7, and 9%) to SBS modified bitumen. Accordingly, rotational viscosity (RV) tests and rheological tests with dynamic shear rheometer (DSR) based on the determination of complex shear modulus (|G*|) and phase angle (δ) were conducted along with the traditional bitumen tests. As a result of the experimental study, it was observed that adding WCO increased the workability and fatigue resistance of SBSMB, however, decreased its rutting resistance. Therefore, the mixing and compaction temperatures of SBSMB can be decreased by adding low amounts of WCO without excessive performance loss. Thus, during the construction of asphalt pavements, environmental damage can be reduced by utilizing waste materials and reducing CO2 emissions.
- 1 November 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (6) , 1-18
Open AccessInvestigation of Rheological and Physical Properties of SBS and WCO Composite Modified Bitumen
Nowadays, the use of waste materials in various industries is becoming widespread in order to promote waste recycling. Thus, scientists are researching the use of waste materials in bitumen modification. In this study, it was aimed to investigate the effect of waste cooking oil (WCO) on the physical and rheological properties of unaged Styrene-Butadiene-Styrene modified bitumen (SBSMB) by adding WCO at different ratios (1, 3, 5, 7, and 9%) to SBS modified bitumen. Accordingly, rotational viscosity (RV) tests and rheological tests with dynamic shear rheometer (DSR) based on the determination of complex shear modulus (|G*|) and phase angle (δ) were conducted along with the traditional bitumen tests. As a result of the experimental study, it was observed that adding WCO increased the workability and fatigue resistance of SBSMB, however, decreased its rutting resistance. Therefore, the mixing and compaction temperatures of SBSMB can be decreased by adding low amounts of WCO without excessive performance loss. Thus, during the construction of asphalt pavements, environmental damage can be reduced by utilizing waste materials and reducing CO2 emissions.
- 4 October 2024
- Published by Gumushane University Journal of Science and Technology Institute in Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Highway application control enhanced by algorithm-based new ınterface software
One of the significant challenges encountered during the implementation of highway projects today is the inability to perform accurate and timely inspections. This results in both loss of time and the potential for uncontrolled construction at various points due to insufficient control capabilities at every site. During the preparation of highway projects, cross-sections of only specific points can be obtained, which limits the scope of inspection during implementation. The ability to inspect points outside these cross-sections and control the areas beyond the axis line of the cross-section points during the project execution would provide a significant advantage. Additionally, this approach would result in time and cost savings, enabling the swift execution and control of construction at points outside the cross-section axis line according to project requirements. In this context, an algorithm has been designed to instantly calculate the distance of any point from the starting point, its distance from the road axis, and the required elevation along the designed elevation profile. This algorithm has been utilized to develop a computer program (interface software) to instantly calculate all relevant data for any given point during the project construction phase. For instance, in a completed highway project, using this interface facilitated the analyses of cost benefits achieved.
- 4 October 2024
- Published by Gumushane University Journal of Science and Technology Institute in Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Highway application control enhanced by algorithm-based new ınterface software
One of the significant challenges encountered during the implementation of highway projects today is the inability to perform accurate and timely inspections. This results in both loss of time and the potential for uncontrolled construction at various points due to insufficient control capabilities at every site. During the preparation of highway projects, cross-sections of only specific points can be obtained, which limits the scope of inspection during implementation. The ability to inspect points outside these cross-sections and control the areas beyond the axis line of the cross-section points during the project execution would provide a significant advantage. Additionally, this approach would result in time and cost savings, enabling the swift execution and control of construction at points outside the cross-section axis line according to project requirements. In this context, an algorithm has been designed to instantly calculate the distance of any point from the starting point, its distance from the road axis, and the required elevation along the designed elevation profile. This algorithm has been utilized to develop a computer program (interface software) to instantly calculate all relevant data for any given point during the project construction phase. For instance, in a completed highway project, using this interface facilitated the analyses of cost benefits achieved.
- Open Access
- 1 July 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (4) , 1-26
Investigation of Rutting and Low Temperature Cracking Behavior of Reactive Ethylene Terpolymer and Waste Cooking Oil Modified Bitumen
With sustainability being the most crucial issue of recent years, the use of waste materials in bitumen modification is increasing and becoming widespread. In this experimental study, it was aimed to investigate the high- and low-temperature behavior of bitumen samples modified with waste cooking oil (WCO), reactive ethylene terpolymer (RET), and polyphosphoric acid (PPA). Accordingly, the multiple stress creep and recovery (MSCR) test and the bending beam rheometer (BBR) test were conducted. Depending on the increasing WCO ratio, the Jnr,R%,∆T_c,and λ parameters of modified bitumens were examined in detail. It was observed that with increasing WCO ratio,the Jnr value increased, and elastic recovery and stiffness decreased. In addition, it has been determined that this composite-modified bitumen is resistant to heavy traffic loads and has sufficient flexibility at low temperatures.
- 1 July 2024
- Published by Teknik Dergi in Turkish Journal of Civil Engineering
- Vol. 35 (4) , 1-26
Open AccessInvestigation of Rutting and Low Temperature Cracking Behavior of Reactive Ethylene Terpolymer and Waste Cooking Oil Modified Bitumen
With sustainability being the most crucial issue of recent years, the use of waste materials in bitumen modification is increasing and becoming widespread. In this experimental study, it was aimed to investigate the high- and low-temperature behavior of bitumen samples modified with waste cooking oil (WCO), reactive ethylene terpolymer (RET), and polyphosphoric acid (PPA). Accordingly, the multiple stress creep and recovery (MSCR) test and the bending beam rheometer (BBR) test were conducted. Depending on the increasing WCO ratio, the Jnr,R%,∆T_c,and λ parameters of modified bitumens were examined in detail. It was observed that with increasing WCO ratio,the Jnr value increased, and elastic recovery and stiffness decreased. In addition, it has been determined that this composite-modified bitumen is resistant to heavy traffic loads and has sufficient flexibility at low temperatures.
- Open Access
- 28 May 2024
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- Vol. 29 (2) , 639-658
THE USE OF GRAPHENE IN THE MODIFICATION OF BITUMEN: A LITERATURE REVIEW
In recent years, nanomaterials in bitumen modification have become widespread due to their superior properties. Graphene and its derivatives are prominent examples of this. Therefore, this review study was conducted to evaluate the effect of graphene on bitumen in detail. Accordingly, by examining the literature studies, general information about graphene and its derivatives was given, and the preparation conditions of graphene-modified bitumen were evaluated. Then, the effect of graphene on the physical and rheological properties of bitumen was investigated. In addition, the impact of graphene modification on the performance of asphalt mixtures and the use of graphene in composite modification was investigated. As a result, it was determined that graphene improves the high-temperature performance of bitumen, but its effect on the low-temperature and fatigue performance of bitumen is mostly negligible. In addition, it has been determined that graphene increases the rutting resistance of bituminous mixtures and positively affects the cracking resistance of bituminous mixtures in general.
- 28 May 2024
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- Vol. 29 (2) , 639-658
Open AccessTHE USE OF GRAPHENE IN THE MODIFICATION OF BITUMEN: A LITERATURE REVIEW
In recent years, nanomaterials in bitumen modification have become widespread due to their superior properties. Graphene and its derivatives are prominent examples of this. Therefore, this review study was conducted to evaluate the effect of graphene on bitumen in detail. Accordingly, by examining the literature studies, general information about graphene and its derivatives was given, and the preparation conditions of graphene-modified bitumen were evaluated. Then, the effect of graphene on the physical and rheological properties of bitumen was investigated. In addition, the impact of graphene modification on the performance of asphalt mixtures and the use of graphene in composite modification was investigated. As a result, it was determined that graphene improves the high-temperature performance of bitumen, but its effect on the low-temperature and fatigue performance of bitumen is mostly negligible. In addition, it has been determined that graphene increases the rutting resistance of bituminous mixtures and positively affects the cracking resistance of bituminous mixtures in general.
- Open Access
- 16 April 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (3) , 1493-1510
Investigation of the Effect of Boron Oxide and Beeswax on Workability and High-Temperature Performance of Bitumen
In recent years, various studies have shown that boron-containing additives improve the rutting performance of the bituminous pavements. However, in these studies, it was stated that these additives would decrease the workability of the bitumen and increase energy required for the construction of the pavement. On the other hand, it has been shown in many studies that waxes increase the workability of the bitumen. In this study, it was aimed to obtain bitumen with high rutting resistance and workability by adding boron oxide (BO) and beeswax (BW) to bitumen. Therefore, modified bitumen was produced by adding BO and BW at different ratios to a 50/70 penetration grade base bitumen. Then, the chemical, physical, and rheological properties of modified bitumen samples were investigated by various experiments. As a result, it has been observed that BO increases the high-temperature performance and viscosity of bitumen; on the other hand, BW decreases rutting resistance and viscosity. When BO and BW were added together to the bitumen, the negative impact of BO on workability and the negative impact of BW on high temperature performance were significantly eliminated. Especially, in 1BO + 1BW and 3BO + 3BW bitumens, the high-temperature performance of the bitumen improved without decreasing the workability.
- 16 April 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (3) , 1493-1510
Open AccessInvestigation of the Effect of Boron Oxide and Beeswax on Workability and High-Temperature Performance of Bitumen
In recent years, various studies have shown that boron-containing additives improve the rutting performance of the bituminous pavements. However, in these studies, it was stated that these additives would decrease the workability of the bitumen and increase energy required for the construction of the pavement. On the other hand, it has been shown in many studies that waxes increase the workability of the bitumen. In this study, it was aimed to obtain bitumen with high rutting resistance and workability by adding boron oxide (BO) and beeswax (BW) to bitumen. Therefore, modified bitumen was produced by adding BO and BW at different ratios to a 50/70 penetration grade base bitumen. Then, the chemical, physical, and rheological properties of modified bitumen samples were investigated by various experiments. As a result, it has been observed that BO increases the high-temperature performance and viscosity of bitumen; on the other hand, BW decreases rutting resistance and viscosity. When BO and BW were added together to the bitumen, the negative impact of BO on workability and the negative impact of BW on high temperature performance were significantly eliminated. Especially, in 1BO + 1BW and 3BO + 3BW bitumens, the high-temperature performance of the bitumen improved without decreasing the workability.
- Open Access
- 1 August 2023
- Published by Croatian Association of Civil Engineers in Journal of the Croatian Association of Civil Engineers
- Vol. 75 (07) , 679-694
Rheological properties of synthesised additives in hot mix asphalt
- 1 August 2023
- Published by Croatian Association of Civil Engineers in Journal of the Croatian Association of Civil Engineers
- Vol. 75 (07) , 679-694
Open AccessRheological properties of synthesised additives in hot mix asphalt
- Open Access
The Influence of SBS, Viatop Premium and FRP on the Improvement of Stone Mastic Asphalt Performance
The current study investigates the effects of Fiber Reinforce Polymer (FRP) additive on the performance of Stone Mastic Asphalt (SMA) mixtures with SBS and Viatop Premium additives. The asphalt mixture used in the current study included SBS (Styrene-Butadiene-Styrene) additive modified at the rate of 5% according to the necessary preliminary studies, and some SMA mixture modified by adding FRP (Fiber Reinforced Polymers) additive prepared in dimensions of 5 cm in different proportions (0.3%, 0.5%, 0.7% and 0.9%). The mechanical properties of the mixtures were investigated, and the findings revealed that the SMA mixture; prepared by adding FRP additive, SBS modified bitumen, and Viatop Premium additive; increased the rutting, aging resistance and elasticity of SMAs. Moreover, load spread ability and fatigue life revealed an increase, whereas high temperature sensitivity and tendency to crack at low temperatures decreased throughout the study. The FRP contribution rate that improves the performance characteristics of the SMA mixture to the highest level was found to be 0.7%.
Open AccessThe Influence of SBS, Viatop Premium and FRP on the Improvement of Stone Mastic Asphalt Performance
The current study investigates the effects of Fiber Reinforce Polymer (FRP) additive on the performance of Stone Mastic Asphalt (SMA) mixtures with SBS and Viatop Premium additives. The asphalt mixture used in the current study included SBS (Styrene-Butadiene-Styrene) additive modified at the rate of 5% according to the necessary preliminary studies, and some SMA mixture modified by adding FRP (Fiber Reinforced Polymers) additive prepared in dimensions of 5 cm in different proportions (0.3%, 0.5%, 0.7% and 0.9%). The mechanical properties of the mixtures were investigated, and the findings revealed that the SMA mixture; prepared by adding FRP additive, SBS modified bitumen, and Viatop Premium additive; increased the rutting, aging resistance and elasticity of SMAs. Moreover, load spread ability and fatigue life revealed an increase, whereas high temperature sensitivity and tendency to crack at low temperatures decreased throughout the study. The FRP contribution rate that improves the performance characteristics of the SMA mixture to the highest level was found to be 0.7%.
- Open Access
- 1 April 2017
- Published by Croatian Association of Civil Engineers in Journal of the Croatian Association of Civil Engineers
- Vol. 69 (3) , 215-220
Optimizing activated carbon size and ratio in bitumen modification
- 1 April 2017
- Published by Croatian Association of Civil Engineers in Journal of the Croatian Association of Civil Engineers
- Vol. 69 (3) , 215-220
Open AccessOptimizing activated carbon size and ratio in bitumen modification