Illya O. Klimenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Illya O. Klimenko has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Viktoriya Ya. Podhurska
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
7 shared publications - Galyna N. Tolmachova
National Science Center “Kharkiv Institute of Physics and Technology”, National Academy of Sciences of Ukraine, Kharkiv, Ukraine
6 shared publications - Igor V. Kolodiy
Kharkiv Institute of Physics and Technology
4 shared publications - Orest P. Ostash
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
4 shared publications - Valeriy D. Ovcharenko
National Science Center “Kharkiv Institute of Physics and Technology”, National Academy of Sciences of Ukraine, Kharkiv, Ukraine
4 shared publications - Alexander S. Kuprin
National Science Center “Kharkiv Institute of Physics and Technology”, National Academy of Sciences of Ukraine, Kharkiv, Ukraine
3 shared publications
Latest Publications
- 4 November 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (5) , 76-83
High-temperature wear resistance of Ti–6Al–4V alloy with nanostructured TiN/CrN multilayer coatings
The effect of ion-plasma surface modification (IPM) in an Ar/N2 atmosphere and the deposition of cathodic-arc TiN and CrN coatings with different architectures on the mechanical and tribological properties of Ti–6Al–4V alloy was investigated at 20°C and 500°C. The best improvement in wear resistance was achieved by combining IPM with the deposition of a multilayer TiN/CrN coating with a modulation period of 10 nm. The for¬mation of a superlattice structure in the coating with a hardness of 29 GPa radically improves its tribological behavior: the friction coefficient decreases to 0.25 and 0.5, while the specific wear rate to 1x10–6 and 1.1x10–5 mm3/(N·m), respectively at 20°C and 500°C.
- 4 November 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (5) , 76-83
High-temperature wear resistance of Ti–6Al–4V alloy with nanostructured TiN/CrN multilayer coatings
The effect of ion-plasma surface modification (IPM) in an Ar/N2 atmosphere and the deposition of cathodic-arc TiN and CrN coatings with different architectures on the mechanical and tribological properties of Ti–6Al–4V alloy was investigated at 20°C and 500°C. The best improvement in wear resistance was achieved by combining IPM with the deposition of a multilayer TiN/CrN coating with a modulation period of 10 nm. The for¬mation of a superlattice structure in the coating with a hardness of 29 GPa radically improves its tribological behavior: the friction coefficient decreases to 0.25 and 0.5, while the specific wear rate to 1x10–6 and 1.1x10–5 mm3/(N·m), respectively at 20°C and 500°C.
- 10 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (4) , 32-40
Wear resistance of vacuum-arc nitride coatings deposited on nitrided 35KhM steel
The results of tribological tests at 20°C and 250°C of 35KHM steel in the initial state and after complex surface modification: nitriding and vacuum-arc TiN, CrN and Mo2N coatings deposition, are presented. Nitriding only slightly changes the tribological charac¬teristics at 20°C, but at 250°C it contributes to an increase in the specific wear rate (W = 2x10–4 mm3/(Nxm)). The TiN coating causes its decrease (W = 2x10–5 mm3/(Nxm)), but it is characterized by a high and unstable friction coefficient at both test temperatures (µ = 0.75-1.06). The CrN coating demonstrates satisfactory tribological properties, espe¬cially at 20°C in a friction pair with a TiN-coated ball (µ = 0.38 and W = 1x10–7 mm3/(Nxm)). The best results are demonstrated by the Mo2N coating in a pair with a TiN coating, which provides low stable friction coefficients (0.38–0.54) and a minimum specific wear rate (W = 1x10–7 mm3/(Nxm)) regardless of the test temperature.
- 10 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (4) , 32-40
Wear resistance of vacuum-arc nitride coatings deposited on nitrided 35KhM steel
The results of tribological tests at 20°C and 250°C of 35KHM steel in the initial state and after complex surface modification: nitriding and vacuum-arc TiN, CrN and Mo2N coatings deposition, are presented. Nitriding only slightly changes the tribological charac¬teristics at 20°C, but at 250°C it contributes to an increase in the specific wear rate (W = 2x10–4 mm3/(Nxm)). The TiN coating causes its decrease (W = 2x10–5 mm3/(Nxm)), but it is characterized by a high and unstable friction coefficient at both test temperatures (µ = 0.75-1.06). The CrN coating demonstrates satisfactory tribological properties, espe¬cially at 20°C in a friction pair with a TiN-coated ball (µ = 0.38 and W = 1x10–7 mm3/(Nxm)). The best results are demonstrated by the Mo2N coating in a pair with a TiN coating, which provides low stable friction coefficients (0.38–0.54) and a minimum specific wear rate (W = 1x10–7 mm3/(Nxm)) regardless of the test temperature.
- Open Access
- 12 June 2026
- Published by Elsevier in SSRN Electronic Journal
Cavitation erosion resistance and mechanical properties of Ti-rich high-entropy alloys
The cavitation erosion characteristics and mechanical properties of three Ti-rich lightweight high-entropy alloys (HEAs) were investigated and compared with those of the commercial-grade Ti6Al4V alloy. It was established that among the studied HEAs, the quinary Ti60Cr11Al7Nb11V11 (HEA-1) alloy exhibited the highest resistance to cavitation erosion. The erosion resistance of the quaternary Ti60Cr11Al7Nb22 (HEA-2) and Ti60Cr11Al7V22 (HEA-3) alloys was approximately 1.25 and 1.43 times lower than that of HEA-1, respectively. Notably, Ti6Al4V alloy exhibited the lowest erosion resistance despite possessing the highest hardness. All investigated HEAs were characterized by a single-phase BCC structure, similar hardness, and high tensile ductility, which was approximately three times higher than that of Ti6Al4V. Furthermore, the yield strength of the quinary HEA-1 alloy exceeded that of the other HEAs, while its ultimate tensile strength and strain-hardening capacity were the highest among all tested materials. Microstructural differences in the failure mechanisms between the HEAs and the Ti6Al4V alloy are discussed. Based on the experimental results, empirical correlations relating cavitation erosion resistance to the mechanical properties under quasi-static loading are proposed.
- 12 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCavitation erosion resistance and mechanical properties of Ti-rich high-entropy alloys
The cavitation erosion characteristics and mechanical properties of three Ti-rich lightweight high-entropy alloys (HEAs) were investigated and compared with those of the commercial-grade Ti6Al4V alloy. It was established that among the studied HEAs, the quinary Ti60Cr11Al7Nb11V11 (HEA-1) alloy exhibited the highest resistance to cavitation erosion. The erosion resistance of the quaternary Ti60Cr11Al7Nb22 (HEA-2) and Ti60Cr11Al7V22 (HEA-3) alloys was approximately 1.25 and 1.43 times lower than that of HEA-1, respectively. Notably, Ti6Al4V alloy exhibited the lowest erosion resistance despite possessing the highest hardness. All investigated HEAs were characterized by a single-phase BCC structure, similar hardness, and high tensile ductility, which was approximately three times higher than that of Ti6Al4V. Furthermore, the yield strength of the quinary HEA-1 alloy exceeded that of the other HEAs, while its ultimate tensile strength and strain-hardening capacity were the highest among all tested materials. Microstructural differences in the failure mechanisms between the HEAs and the Ti6Al4V alloy are discussed. Based on the experimental results, empirical correlations relating cavitation erosion resistance to the mechanical properties under quasi-static loading are proposed.
- 9 March 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (1) , 31-41
Multi-component titanium-based coatings for lightweight solid oxide fuel cell interconnects
The composition, structure, mechanical characteristics, long-term oxidation resistance and electrical conductivity of coatings produced by vacuum-arc deposition method using a cathode (target) made of Ti–6.1Al–5.5Zr–2.3Sn–0.8Mn–0.6Si–0.4Mo–0.3Nb titanium alloy were studied. The coatings were deposited on a 0.5 mm thick substrate made of a cost-effective Ti–2.2Al–1.5Mn–0.3Zr–0.3Fe–0.1C alloy at a substrate bias voltage Ubias = –50…–200 V. The properties of the materials were compared in the as-received state and after long-term holding for 1000 h at 600°C in air, simulating the effect of the cathode environment in solid oxide fuel cells (SOFCs). It was established that the plates with a 10 mm thick coating at Ubias = -100 V exhibit high oxidation resistance (Δm/S = 0.88 mg/cm2) and surface electrical conductivity in the oxidized state (σ = 2.4×105 S/m) and meet the requirements for lightweight interconnect materials in cathode side of intermediate-temperature SOFCs.
- 9 March 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (1) , 31-41
Multi-component titanium-based coatings for lightweight solid oxide fuel cell interconnects
The composition, structure, mechanical characteristics, long-term oxidation resistance and electrical conductivity of coatings produced by vacuum-arc deposition method using a cathode (target) made of Ti–6.1Al–5.5Zr–2.3Sn–0.8Mn–0.6Si–0.4Mo–0.3Nb titanium alloy were studied. The coatings were deposited on a 0.5 mm thick substrate made of a cost-effective Ti–2.2Al–1.5Mn–0.3Zr–0.3Fe–0.1C alloy at a substrate bias voltage Ubias = –50…–200 V. The properties of the materials were compared in the as-received state and after long-term holding for 1000 h at 600°C in air, simulating the effect of the cathode environment in solid oxide fuel cells (SOFCs). It was established that the plates with a 10 mm thick coating at Ubias = -100 V exhibit high oxidation resistance (Δm/S = 0.88 mg/cm2) and surface electrical conductivity in the oxidized state (σ = 2.4×105 S/m) and meet the requirements for lightweight interconnect materials in cathode side of intermediate-temperature SOFCs.
- 1 May 2025
- Published by Springer Nature in Materials Science
- Vol. 60 (6) , 792-799
Structure and tribological properties of MoN cathodic-arc coating
- 1 May 2025
- Published by Springer Nature in Materials Science
- Vol. 60 (6) , 792-799
Structure and tribological properties of MoN cathodic-arc coating
- 1 January 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 105-108
Development and Investigation of Wear-Resistant Nitride Coatings on VT6 Titanium Alloy
Titanium alloy VT6 (Ti-6Al-4V) is widely used in turbine components but suffers from poor tribological performance. In this study, CrN, TiN, and multilayer TiN/CrN coatings deposited on VT6 substrate were evaluated at 20°C and 500°C. Results show that while nitriding reduced wear, the multilayer TiN/CrN coating provided the best performance, combining a low friction coefficient (0.3–0.5) with minimal wear rate of both alloy and counterbody, ensuring superior durability in demanding conditions.
- 1 January 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 105-108
Development and Investigation of Wear-Resistant Nitride Coatings on VT6 Titanium Alloy
Titanium alloy VT6 (Ti-6Al-4V) is widely used in turbine components but suffers from poor tribological performance. In this study, CrN, TiN, and multilayer TiN/CrN coatings deposited on VT6 substrate were evaluated at 20°C and 500°C. Results show that while nitriding reduced wear, the multilayer TiN/CrN coating provided the best performance, combining a low friction coefficient (0.3–0.5) with minimal wear rate of both alloy and counterbody, ensuring superior durability in demanding conditions.
- Open Access
- 5 March 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 380-385
Tribological Properties at 20 and 500°C of TiN and CrN Cathodic ARC Coatings Deposited on Ti-6Al-4V Alloy
Tribological properties of TiN and CrN coatings deposited by cathodic arc method at three different bias potentials -50, -150 and -300V on Ti-6Al-4V alloy in pair with alumina have been investigated. X-ray diffraction analysis showed that single-phase textured cubic nitrides of TiN and CrN were formed in these coatings. It is shown that the friction coefficient of the coatings is practically equal to that established for the Ti6Al4V alloy, but the wear rate is more than an order of magnitude lower than for the titanium alloy substrate. Coatings deposited at a potential of -50 V show optimal tribological properties at temperatures 20 and 500°C. Friction coefficients for TiN coatings are 0.4-0.8 at 20°C and 0,75 at 500°C; for CrN coatings they are 0.5 at 20°C and 0,7 at 500°C. Wear rates for TiN coatings are 0.86·10-5 мм3/Нм at 20°C and 3.56·10-5 мм3/Нм at 500°C; for CrN coatings they are 1.43·10-5 мм3/Нм at 20°C and 7.13·10-5 мм3/Нм at 500°C.
- 5 March 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 380-385
Open AccessTribological Properties at 20 and 500°C of TiN and CrN Cathodic ARC Coatings Deposited on Ti-6Al-4V Alloy
Tribological properties of TiN and CrN coatings deposited by cathodic arc method at three different bias potentials -50, -150 and -300V on Ti-6Al-4V alloy in pair with alumina have been investigated. X-ray diffraction analysis showed that single-phase textured cubic nitrides of TiN and CrN were formed in these coatings. It is shown that the friction coefficient of the coatings is practically equal to that established for the Ti6Al4V alloy, but the wear rate is more than an order of magnitude lower than for the titanium alloy substrate. Coatings deposited at a potential of -50 V show optimal tribological properties at temperatures 20 and 500°C. Friction coefficients for TiN coatings are 0.4-0.8 at 20°C and 0,75 at 500°C; for CrN coatings they are 0.5 at 20°C and 0,7 at 500°C. Wear rates for TiN coatings are 0.86·10-5 мм3/Нм at 20°C and 3.56·10-5 мм3/Нм at 500°C; for CrN coatings they are 1.43·10-5 мм3/Нм at 20°C and 7.13·10-5 мм3/Нм at 500°C.
- Open Access
Mechanical Properties of V-O-N Coatings Synthesized by Cathodic Arc Evaporation
The V-O-N coating set was produced at different relative oxygen concentrations of O2(x) = O2/(N2 +O2) using cathodic arc evaporation. The aim of the research was to determine the effect of oxygen on coating properties. The coatings’ composition and structural properties (X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX)) and mechanical properties—hardness, adhesion, and wear resistance (nano-indenter, scratch tester, ball-on-disc tester)—were extensively investigated. EDX and XRD analyses indicate that in coatings formed with a relative oxygen concentration in the range of 20–30%, the oxygen concentration in the coating increases dramatically from approximately 16 at.%. to 63 at.%, and the nitrogen concentration drops from about 34 at.% up to 3 at.%. This may indicate greater activity of oxygen compared to nitrogen in forming compounds with vanadium. The occurrence of the V5O9 phase belonging to the Magnéli phases was observed. Microscopic observations indicate that the number of surface defects increases with the oxygen concentration in the coating. The opposite effect is characterized by mechanical properties—hardness, adhesion, and wear resistance decrease with increasing oxygen concentration in the coating.
Open AccessMechanical Properties of V-O-N Coatings Synthesized by Cathodic Arc Evaporation
The V-O-N coating set was produced at different relative oxygen concentrations of O2(x) = O2/(N2 +O2) using cathodic arc evaporation. The aim of the research was to determine the effect of oxygen on coating properties. The coatings’ composition and structural properties (X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX)) and mechanical properties—hardness, adhesion, and wear resistance (nano-indenter, scratch tester, ball-on-disc tester)—were extensively investigated. EDX and XRD analyses indicate that in coatings formed with a relative oxygen concentration in the range of 20–30%, the oxygen concentration in the coating increases dramatically from approximately 16 at.%. to 63 at.%, and the nitrogen concentration drops from about 34 at.% up to 3 at.%. This may indicate greater activity of oxygen compared to nitrogen in forming compounds with vanadium. The occurrence of the V5O9 phase belonging to the Magnéli phases was observed. Microscopic observations indicate that the number of surface defects increases with the oxygen concentration in the coating. The opposite effect is characterized by mechanical properties—hardness, adhesion, and wear resistance decrease with increasing oxygen concentration in the coating.
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 126-136
CAVITATION EROSION RESISTANCE OF VACUUM-ARC COATINGS BASED ON TiN
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 126-136
CAVITATION EROSION RESISTANCE OF VACUUM-ARC COATINGS BASED ON TiN
- 1 January 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 118-121
Tribological Properties of Tin And Crn Cathodic Arc Coatings on Ti-6al-4v Alloy
Tribological properties of TiN and CrN coatings deposited by cathodic arc method at three different bias potentials -50, -150 and -300V on Ti-6Al-4V alloy in pair with alumina have been investigated. The wear rate of the coatings is more than an order of magnitude lower than for the titanium alloy substrate. The friction coefficient is in the range of 0.4-0.8 for TiN coatings and 0.5 for CrN coatings. Coatings deposited at a potential of -50 V show optimal tribological properties.
- 1 January 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 118-121
Tribological Properties of Tin And Crn Cathodic Arc Coatings on Ti-6al-4v Alloy
Tribological properties of TiN and CrN coatings deposited by cathodic arc method at three different bias potentials -50, -150 and -300V on Ti-6Al-4V alloy in pair with alumina have been investigated. The wear rate of the coatings is more than an order of magnitude lower than for the titanium alloy substrate. The friction coefficient is in the range of 0.4-0.8 for TiN coatings and 0.5 for CrN coatings. Coatings deposited at a potential of -50 V show optimal tribological properties.