RSRongrong Shang

Rongrong Shang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rongrong Shang has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Combined effects of deformation and subsequent annealing on corrosion behavior of IN625 alloy in HF solution

    by Rongrong Shang, Jianwei Teng, Yidi Li, Yu Wang, Yaxi Zhou, Mengxia Chen, Xiaoxuan Dong, Yunping Li

  • Open Access

    Effect of Cold Rolling on the Mechanical Properties and Corrosion Resistance in Hydrofluoric Acid Solution of Inconel 600 Alloy

    by Xiaoxuan Dong, Yidi Li, Rongrong Shang, Mengxia Chen, Lu Liu, Jianwei Teng, Yunping Li

    In this study, Inconel 600 alloy with reductions of 20%, 50%, and 80% was obtained through cold rolling, and the effects of plastic deformation on its mechanical properties and corrosion behavior in a hydrofluoric acid (HF) solution were systematically investigated. The results show that cold rolling induces pronounced work hardening, with both hardness and strength increasing continuously with increasing reduction, while the ductility decreases accordingly. The alloy with 80% reduction exhibits the highest strength, with an ultimate tensile strength of 1270 MPa and a yield strength of 1210 MPa. In contrast, the macroscopic corrosion resistance of the alloy in HF solution remains essentially unchanged with increasing deformation, although a slight intensification of pitting corrosion is observed. The combined effects of deformation-induced pitting and passivation enhancement resulted in retention of corrosion resistance. These findings demonstrate that appropriate control of cold rolling enables effective mechanical strengthening of Inconel 600 without significantly sacrificing its corrosion performance in aggressive fluorine containing environments.


  • Open Access

    Effect of Ultrasonic Treatment on Chemical Stripping Behavior of Aluminum Coating on K6509 Co-Based Superalloy

    by Yuanyuan Jin, Cheng Xie, Ke Sun, Zehuan Li, Xin Wang, Xin Ma, Hui Wang, Rongrong Shang, Xuxian Zhou, Yidi Li, et al.

    In this study, 10% nitric acid was employed to remove the aluminum coating on the cobalt-based superalloy K6509, with a focus on elucidating the corrosion mechanism and evaluating the effect of ultrasonic on the removal process. The results shows that ultrasonic treatment (40 kHz) significantly improves coating removal efficiency, increasing the maximum corrosion rate by 46.49% from 2.5413 × 10−7 g·s−1·mm−2 to 4.7488 × 10−7 g·s−1·mm−2 and reducing removal time from 10 min to 6 min. This enhancement is attributed to cavitation effect of ultrasonic bubbles and the shockwave-accelerated ion diffusion, which together facilitate more efficient coating degradation and results in a smoother surface. In terms of corrosion behavior, the difference in phase composition between the outer layer and the interdiffusion zone (IDZ) plays a decisive role. The outer layer is primarily composed of β-(Co,Ni)Al phase, which is thermodynamically less stable in acidic environments and thus readily dissolves in 10% HNO3. In contrast, the IDZ mainly consists of Cr23C6, which exhibit high chemical stability and a strong tendency to passivate. These characteristics render the IDZ highly resistant to nitric acid attack, thereby forming a protective barrier that limits acid penetration and helps maintain the integrity of the substrate.


  • Open Access

    Enhanced Anti-Corrosion Performance of Co-Cr-Mo Alloy in Molten Al by Prior Oxidation Treatment

    by Rongrong Shang, Biaobiao Yang, Yunping Li

    Co-based alloys are promising alternatives to replace the currently used tool steels in aluminum die-casting molds for producing sophisticated products. Although the reaction is significantly less severe compared to that of tool steels, bare Co-29Cr-6Mo (CCM) alloy is still gradually corroded under molten Al, leading to the local failure of the alloy due to the formation of intermetallic compounds between the matrix and molten Al. This study indicated that prior oxidation treatment at 750 °C on CCM alloy is beneficial in enhancing the corrosion resistance of the alloy to molten Al. The is more pronounced in the alloy after a longer oxidation treatment. However, after oxidation for longer than 24 h, the protectiveness of the film cannot be enhanced anymore. In addition, even after the full failure of the oxide film, the thickness loss rate of a sample with prior oxidation treatment is much lower than that of a bare sample. This can be attributed to the fact that network-aligned oxide particles of the cone structure boundary inhibit both the outwards movements of alloying elements and the dissolution of the intermetallic layer.