Anđelko Cumbo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anđelko Cumbo has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Gordana Broćeta
University of Banja Luka,Banja Luka,Bosnia and Herzegovina
5 shared publications - Marina Latinović Krndija
University of Banja Luka
3 shared publications - Slobodan Šupić
University of Novi Sad
3 shared publications - Žarko Lazić
University of Banja Luka
3 shared publications - Marina Latinović Krndija
University of Banja Luka,Banja Luka,Bosnia and Herzegovina
2 shared publications - Mirjana Malešev
University of Novi Sad
2 shared publications
Latest Publications
- Open Access
- 31 December 2025
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy in AГГ+
- Vol. 13 (2) , 50-70
The Effect of Masonry Infill Model Selection on the Seismic Response of Reinforced Concrete Frame Structures
In many countries, reinforced concrete (RC) frames are widely utilized as the primary building structure. The infill is typically composed of traditional masonry (brick elements connected with mortar), commonly without isolation from the frame. It is noted that in engineering practice, seismic force calculations for RC frame buildings are often conducted on models that exclude masonry infill, even when the infill is not isolated from the frame through specific construction elements. In such cases, the walls are considered only as a permanent load. Consequently, the contribution of non-insulated (bonded) masonry infill to changes in bearing capacity, stiffness, and ductility of the RC frame, affecting stresses and horizontal movement during seismic activity, is frequently disregarded. To assess the consequences of prevalent calculation models, four representative types of RC frame models with masonry infill were analysed herein. The study demonstrated that differently conceptualized models of the same building impact dynamic characteristics, including forces and displacements of the main frame structure. The dynamic analysis revealed that inadequate treatment of the frame and non-insulated infill connection in the design phase can lead to dangerous phenomena such as "soft floors," significant torsion, and the effects of short columns going unnoticed. Therefore, this paper underscores the importance of appropriately addressing non-insulated infill in the calculation model in routine design practices. Additionally, it advocates for the issuance of precise instructions for special construction measures that would effectively isolate masonry infill from the frame when such a solution is justified.
- 31 December 2025
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy in AГГ+
- Vol. 13 (2) , 50-70
Open AccessThe Effect of Masonry Infill Model Selection on the Seismic Response of Reinforced Concrete Frame Structures
In many countries, reinforced concrete (RC) frames are widely utilized as the primary building structure. The infill is typically composed of traditional masonry (brick elements connected with mortar), commonly without isolation from the frame. It is noted that in engineering practice, seismic force calculations for RC frame buildings are often conducted on models that exclude masonry infill, even when the infill is not isolated from the frame through specific construction elements. In such cases, the walls are considered only as a permanent load. Consequently, the contribution of non-insulated (bonded) masonry infill to changes in bearing capacity, stiffness, and ductility of the RC frame, affecting stresses and horizontal movement during seismic activity, is frequently disregarded. To assess the consequences of prevalent calculation models, four representative types of RC frame models with masonry infill were analysed herein. The study demonstrated that differently conceptualized models of the same building impact dynamic characteristics, including forces and displacements of the main frame structure. The dynamic analysis revealed that inadequate treatment of the frame and non-insulated infill connection in the design phase can lead to dangerous phenomena such as "soft floors," significant torsion, and the effects of short columns going unnoticed. Therefore, this paper underscores the importance of appropriately addressing non-insulated infill in the calculation model in routine design practices. Additionally, it advocates for the issuance of precise instructions for special construction measures that would effectively isolate masonry infill from the frame when such a solution is justified.
- Open Access
- 12 June 2024
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- Vol. 16 (1) , 351-362
EFFECT OF THE HRWRA QUANTITY ON DURABILITY PROPERTIES OF SELF-COMPACTING CONCRETE
The paper presents the results of our own experimental research on the effect of the high range water reducing admixture content – HRWRA (applied in the range from 0.8 to 1.2% by mass of cement – mc) on the properties of self-compacting concrete in the fresh and hardened state. The research showed that increasing the HRWRA content leads to the entrapped porosity reduction – up to 44%, increase of flowability – up to 13%, reduction of viscosity – up to 31%, improvement of passing ability – up to 15% and degradation of sieve segregation resistance of concrete in fresh state – up to 60%. The beneficial effect of the increase in HRWRA was shown on the analysed properties in the hardened state: compressive strength at the age of 28 days – up to 13%, water absorption – up to 61% and freeze/thaw resistance – up to 10%. The difference in the participation of HRWRA from 0.8 to 1.2% mc does not have a statistically significant effect on the density and freeze/thaw resistance with a de-icing agent.
- 12 June 2024
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- Vol. 16 (1) , 351-362
Open AccessEFFECT OF THE HRWRA QUANTITY ON DURABILITY PROPERTIES OF SELF-COMPACTING CONCRETE
The paper presents the results of our own experimental research on the effect of the high range water reducing admixture content – HRWRA (applied in the range from 0.8 to 1.2% by mass of cement – mc) on the properties of self-compacting concrete in the fresh and hardened state. The research showed that increasing the HRWRA content leads to the entrapped porosity reduction – up to 44%, increase of flowability – up to 13%, reduction of viscosity – up to 31%, improvement of passing ability – up to 15% and degradation of sieve segregation resistance of concrete in fresh state – up to 60%. The beneficial effect of the increase in HRWRA was shown on the analysed properties in the hardened state: compressive strength at the age of 28 days – up to 13%, water absorption – up to 61% and freeze/thaw resistance – up to 10%. The difference in the participation of HRWRA from 0.8 to 1.2% mc does not have a statistically significant effect on the density and freeze/thaw resistance with a de-icing agent.
- Open Access
- 12 June 2024
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- Vol. 16 (1) , 363-371
EVALUATION OF PROPERTIES OF MASONRY MORTARS BLENDED WITH CERAMIC WASTE POWDER
Aiming to meet the principals of the modern circular economy, this study explores the possibility of using locally available waste materials in the production of innovative, eco-friendly mortar for masonry. The eco-binder, applied as a substitute for cementitious material, is ceramic waste powder (CWP) generated during the production of ceramic industry elements. Within the experimental program, compositions of twelve types of masonry mortars were designed with volumetric ratios of solid components 1:1:5, 1:0.7:4.2, and 1:1:4 (cement + eco-binder/lime/sand), varying the percentage of cement replacement with ceramic powder (up to 80%). The basic properties of masonry mortars were tested, including consistency, compressive strength, flexural tensile strength, capillary water absorption, and adhesion. The test results indicate that ceramic waste powder can be successfully used as a partial replacement for cement up to high substitution levels, yielding more sustainable masonry mortars for use in load-bearing or non-load-bearing masonry structures.
- 12 June 2024
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- Vol. 16 (1) , 363-371
Open AccessEVALUATION OF PROPERTIES OF MASONRY MORTARS BLENDED WITH CERAMIC WASTE POWDER
Aiming to meet the principals of the modern circular economy, this study explores the possibility of using locally available waste materials in the production of innovative, eco-friendly mortar for masonry. The eco-binder, applied as a substitute for cementitious material, is ceramic waste powder (CWP) generated during the production of ceramic industry elements. Within the experimental program, compositions of twelve types of masonry mortars were designed with volumetric ratios of solid components 1:1:5, 1:0.7:4.2, and 1:1:4 (cement + eco-binder/lime/sand), varying the percentage of cement replacement with ceramic powder (up to 80%). The basic properties of masonry mortars were tested, including consistency, compressive strength, flexural tensile strength, capillary water absorption, and adhesion. The test results indicate that ceramic waste powder can be successfully used as a partial replacement for cement up to high substitution levels, yielding more sustainable masonry mortars for use in load-bearing or non-load-bearing masonry structures.
- Open Access
- 27 November 2023
- Published by National Institute of STEM Research in Archives for Technical Sciences
- Vol. 2 (29) , 23-34
TIME DEPENDENT DEFORMATIONS OF A COUPLED BRIDGE: A CASE STUDY
The bridge's span structure comprises a connected beam designed to support a concrete slab poured over parallel steel supports. Simultaneously, segmental construction, shrinkage, and the flow of concrete play a significant role in stress redistribution over time. The span construction is statically indeterminate due to its connections with the abutments, and temporal deformations occur under additional complex conditions. In this analysis, we employed a calculation model based on the layered finite elements method developed by the authors. This model can be utilized to analyse both statically indeterminate supports and the predicted phased construction method. It accounts for changes in the static system and loading, as well as variations in the layers within the coupled section and the viscous properties of the concrete over time. The calculation analysis results reveal that viscous concrete deformations, combined with different moments of activation of individual segments, have a significant impact on stress redistribution over time. Such intricate analyses are indispensable for ensuring the required safety and cost-effectiveness of the bridge span construction.
- 27 November 2023
- Published by National Institute of STEM Research in Archives for Technical Sciences
- Vol. 2 (29) , 23-34
Open AccessTIME DEPENDENT DEFORMATIONS OF A COUPLED BRIDGE: A CASE STUDY
The bridge's span structure comprises a connected beam designed to support a concrete slab poured over parallel steel supports. Simultaneously, segmental construction, shrinkage, and the flow of concrete play a significant role in stress redistribution over time. The span construction is statically indeterminate due to its connections with the abutments, and temporal deformations occur under additional complex conditions. In this analysis, we employed a calculation model based on the layered finite elements method developed by the authors. This model can be utilized to analyse both statically indeterminate supports and the predicted phased construction method. It accounts for changes in the static system and loading, as well as variations in the layers within the coupled section and the viscous properties of the concrete over time. The calculation analysis results reveal that viscous concrete deformations, combined with different moments of activation of individual segments, have a significant impact on stress redistribution over time. Such intricate analyses are indispensable for ensuring the required safety and cost-effectiveness of the bridge span construction.
- Open Access
- 13 June 2022
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- No. 15,p. 45-52
THE INFLUENCE OF CONCRETE VISCOUS DEFORMATIONS DURING BEHAVIOR CALCULATION OF CABLE-STAYED BRIDGES
On the calculation example of a cable-stayed bridge with oblique cables, it was pointed out the shrinkage and creep of concrete significantly affects the distribution of stresses and deflections of the span beam over time. The segmental type of bridge construction is considered, which implies the successive introduction of concrete rheology, for cases of controlled and free beam deflections during construction, i.e. with or without cable tightening on previously performed segments. The phenomenon of reduced sensitivity of the span beam to the effects of concrete rheology is pointed out, in case of controlled deflections by cable tightening, while without cable tightening the deflections increase over time and can negatively affect the usability of the structure. The analyses were performed using an appropriate algorithm (developed by the author) which introduced composite layered finite elements with viscous properties into the calculation.
- 13 June 2022
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- No. 15,p. 45-52
Open AccessTHE INFLUENCE OF CONCRETE VISCOUS DEFORMATIONS DURING BEHAVIOR CALCULATION OF CABLE-STAYED BRIDGES
On the calculation example of a cable-stayed bridge with oblique cables, it was pointed out the shrinkage and creep of concrete significantly affects the distribution of stresses and deflections of the span beam over time. The segmental type of bridge construction is considered, which implies the successive introduction of concrete rheology, for cases of controlled and free beam deflections during construction, i.e. with or without cable tightening on previously performed segments. The phenomenon of reduced sensitivity of the span beam to the effects of concrete rheology is pointed out, in case of controlled deflections by cable tightening, while without cable tightening the deflections increase over time and can negatively affect the usability of the structure. The analyses were performed using an appropriate algorithm (developed by the author) which introduced composite layered finite elements with viscous properties into the calculation.
- Open Access
- 1 December 2021
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- No. 15,p. 540-551
DYNAMIC AMPLIFICATION FACTOR OF ROAD BRIDGES – ANALYTICAL AND EXPERIMENTAL FINDINGS
This paper discusses the problem of theoretical and experimental determination of dynamic factors of road bridges. Various parameters influencing the dynamic behavior of bridges are briefly described and a review of regulations in this field is given. Also, an example of the numerical determination of the dynamic amplification factor on a specific bridge structure using dynamic time history analysis in SAP2000 software is presented. Some established methods for the experimental control of the design dynamic amplification on real structures are given, as well as a data and analysis of experimentally obtained results on a series of concrete bridges on the Banja Luka-Doboj highway.
- 1 December 2021
- Published by University of Banja Luka, Faculty of Architecture, Civil Engineering and Geodesy
- No. 15,p. 540-551
Open AccessDYNAMIC AMPLIFICATION FACTOR OF ROAD BRIDGES – ANALYTICAL AND EXPERIMENTAL FINDINGS
This paper discusses the problem of theoretical and experimental determination of dynamic factors of road bridges. Various parameters influencing the dynamic behavior of bridges are briefly described and a review of regulations in this field is given. Also, an example of the numerical determination of the dynamic amplification factor on a specific bridge structure using dynamic time history analysis in SAP2000 software is presented. Some established methods for the experimental control of the design dynamic amplification on real structures are given, as well as a data and analysis of experimentally obtained results on a series of concrete bridges on the Banja Luka-Doboj highway.