SachchidaNand Shukla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
SachchidaNand Shukla has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Geetika Srivastava
Department of Physics and Electronics, Dr. Rammanohar Lohia Avadh University, Ayodhya, India
5 shared publications - Syed Shamroz Arshad
Department of Physics and Electronics, Dr. Ram Manohar Lohia Avadh University, Ayodhya, Uttar Pradesh, India
4 shared publications - Aditya Sharma
Department of Genetics, University of Delhi South Campus, New Delhi, India
1 shared publication - Anil Kumar
Amity School of Engineering and Technology, Amity University, Lucknow Campus, Lucknow, Uttar Pradesh, India
1 shared publication - Ashish Dixit
Amity University Uttar Pradesh
1 shared publication B.K. Pandey
1 shared publication
Latest Publications
- 15 May 2026
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
Low Power Electronically Tunable Compound Sziklai Pair-Based Low Noise Amplifier for High Frequency Applications
Low Noise Figure (NF) and gain flatness over a wide frequency band are critical Low Noise Amplifier (LNA) performance parameters in high frequency applications. This paper presents a low-power, Cascode Feedback (CASF) compound Sziklai pair Low-Noise Amplifier (LNA) operating across 3.4–39.82[ ]GHz frequency, making it suitable for Ultra-Wideband (UWB) and lower Millimeter-Wave (mmWave) applications in RF front-end systems. By leveraging a CASF structure with NMOS Sziklai pair and complementary Sziklai pair, the proposed LNA achieves low input and output impedances, leading to improved broadband performance. A [ ] Impedance Tuning Circuit (ITC) is employed to tune the gain and other parameters, further enhancing gain and overall performance. Active bias is used to provide appropriate DC bias to the transistors, which strengthens current feedback and mitigates narrowband limitations. By using a CASF structure with lower transconductance transistors, power consumption is significantly reduced. Simulations performed in the CMOS 180[ ]nm process show peak voltage gain of 19.51[ ]dB with a bandwidth of 36.42[ ]GHz and peak current gain of 39.87[ ]dB. These results represent substantial improvements compared to the conventional PMOS Sziklai LNA approach, with nearly double the voltage gain and four times the current gain. Furthermore, the LNA exhibits NF of 0.343[ ]dB at 10[ ]GHz, Input Third-Order Intercept Point (IIP3) of 1.5[ ]dBm, and a chip area of [ ]m 2 . The power consumption is [ ]W from a 1.5[ ]V DC supply, representing an 84.11% reduction compared to the PMOS Sziklai LNA. The proposed LNA also addresses the shortcomings of high-power consumption, low phase margin, and high harmonic distortions of PMOS Sziklai LNAs and low gain, narrow bandwidth, and high NF of the Darlington RF CASF amplifier.
- 15 May 2026
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
Low Power Electronically Tunable Compound Sziklai Pair-Based Low Noise Amplifier for High Frequency Applications
Low Noise Figure (NF) and gain flatness over a wide frequency band are critical Low Noise Amplifier (LNA) performance parameters in high frequency applications. This paper presents a low-power, Cascode Feedback (CASF) compound Sziklai pair Low-Noise Amplifier (LNA) operating across 3.4–39.82[ ]GHz frequency, making it suitable for Ultra-Wideband (UWB) and lower Millimeter-Wave (mmWave) applications in RF front-end systems. By leveraging a CASF structure with NMOS Sziklai pair and complementary Sziklai pair, the proposed LNA achieves low input and output impedances, leading to improved broadband performance. A [ ] Impedance Tuning Circuit (ITC) is employed to tune the gain and other parameters, further enhancing gain and overall performance. Active bias is used to provide appropriate DC bias to the transistors, which strengthens current feedback and mitigates narrowband limitations. By using a CASF structure with lower transconductance transistors, power consumption is significantly reduced. Simulations performed in the CMOS 180[ ]nm process show peak voltage gain of 19.51[ ]dB with a bandwidth of 36.42[ ]GHz and peak current gain of 39.87[ ]dB. These results represent substantial improvements compared to the conventional PMOS Sziklai LNA approach, with nearly double the voltage gain and four times the current gain. Furthermore, the LNA exhibits NF of 0.343[ ]dB at 10[ ]GHz, Input Third-Order Intercept Point (IIP3) of 1.5[ ]dBm, and a chip area of [ ]m 2 . The power consumption is [ ]W from a 1.5[ ]V DC supply, representing an 84.11% reduction compared to the PMOS Sziklai LNA. The proposed LNA also addresses the shortcomings of high-power consumption, low phase margin, and high harmonic distortions of PMOS Sziklai LNAs and low gain, narrow bandwidth, and high NF of the Darlington RF CASF amplifier.
- 15 September 2024
- Published by Springer Nature in International Journal of Information Technology
- Vol. 17 (1) , 301-319
Design of ultra-wideband Sziklai pair based LNAs for wireless communication applications
- 15 September 2024
- Published by Springer Nature in International Journal of Information Technology
- Vol. 17 (1) , 301-319
Design of ultra-wideband Sziklai pair based LNAs for wireless communication applications
- 23 May 2024
- Published by Elsevier in Chemical Physics Letters
- Vol. 846
Studies on thermal conductivity of metallic nanoparticles with varying shape and size
- 23 May 2024
- Published by Elsevier in Chemical Physics Letters
- Vol. 846
Studies on thermal conductivity of metallic nanoparticles with varying shape and size
- Open Access
- 1 March 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (1) , 559-565
Low power CMOS Gm-C based low pass filter for front end neural signal processing
The sub 100 µV voltage levels and sub 100 Hz frequency range makes the processing of most popular signal electroencephalograph (EEG) for brain functionality analysis, a complex task. The low frequency content of EEG (useful signals below 70 Hz) is commonly used for diagnosis of various brain related disorders making low-pass filter (LPF) a key block in front-end processing as noise reduction and resolution enhancement is crucial for precise recovery of these information. This paper is aimed to design reduced transconductance (Gm) based low power and small area CMOS LPF with cutoff frequency (fc) around 70 Hz. The proposed design is simulated using Cadence virtuoso tool and gives cut-off frequency of 72.958 Hz with low output noise of 3.0609 µV/√Hz and power consumption of 264.060 nW at operating voltage of 0.4 V. The simulation results show linearity of performance over -40 to 100 °C. Layout of circuit takes up area of 86.74×81.21 µm and post layout simulation shows 5% variation in power consumption as compared to pre layout simulations.
- 1 March 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (1) , 559-565
Open AccessLow power CMOS Gm-C based low pass filter for front end neural signal processing
The sub 100 µV voltage levels and sub 100 Hz frequency range makes the processing of most popular signal electroencephalograph (EEG) for brain functionality analysis, a complex task. The low frequency content of EEG (useful signals below 70 Hz) is commonly used for diagnosis of various brain related disorders making low-pass filter (LPF) a key block in front-end processing as noise reduction and resolution enhancement is crucial for precise recovery of these information. This paper is aimed to design reduced transconductance (Gm) based low power and small area CMOS LPF with cutoff frequency (fc) around 70 Hz. The proposed design is simulated using Cadence virtuoso tool and gives cut-off frequency of 72.958 Hz with low output noise of 3.0609 µV/√Hz and power consumption of 264.060 nW at operating voltage of 0.4 V. The simulation results show linearity of performance over -40 to 100 °C. Layout of circuit takes up area of 86.74×81.21 µm and post layout simulation shows 5% variation in power consumption as compared to pre layout simulations.
- Open Access
- 1 December 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 14 (4) , 2283-2292
Novel complementary Sziklai pair based high gain low noise small-signal amplifiers
A new paired configuration of opposite polarity BJTs, the “complementary Sziklai pair” is introduced in the series of multi-BJT-based devices like Darlington and Sziklai pair, and its viability is tested in small-signal common emitter (CE) and common collector (CC) amplifier configurations. The Darlington and Sziklai both face the problem of poor frequency response at a higher frequency which is addressed by the proposed configuration. The proposed pair with CE amplifier holds class-A amplification property with a high voltage gain of 200.05, a high current gain of 11.62, wider bandwidth of 1.64 MHz, and a low THD of 1.29E-6%, hence supports the potential of wide applicability in analog communication. Similarly, the proposed pair with CC configuration produces approximately a unit current gain of 0.99 with wider bandwidth of 1.90 MHz and low THD of 1.76E-6%, therefore it can be used as a current buffer in a generalized current follower circuit. Conclusively, the device structure of this new BJT pair may be considered the third consecutive member of the series of Darlington pair and Sziklai pair. The layout of the proposed CE and CC amplifier occupy small areas of 158.30 μm2 (10.23×15.47 μm) and 141.16 μm2 (10.20×13.84 μm) respectively in 180 nm process technology.
- 1 December 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 14 (4) , 2283-2292
Open AccessNovel complementary Sziklai pair based high gain low noise small-signal amplifiers
A new paired configuration of opposite polarity BJTs, the “complementary Sziklai pair” is introduced in the series of multi-BJT-based devices like Darlington and Sziklai pair, and its viability is tested in small-signal common emitter (CE) and common collector (CC) amplifier configurations. The Darlington and Sziklai both face the problem of poor frequency response at a higher frequency which is addressed by the proposed configuration. The proposed pair with CE amplifier holds class-A amplification property with a high voltage gain of 200.05, a high current gain of 11.62, wider bandwidth of 1.64 MHz, and a low THD of 1.29E-6%, hence supports the potential of wide applicability in analog communication. Similarly, the proposed pair with CC configuration produces approximately a unit current gain of 0.99 with wider bandwidth of 1.90 MHz and low THD of 1.76E-6%, therefore it can be used as a current buffer in a generalized current follower circuit. Conclusively, the device structure of this new BJT pair may be considered the third consecutive member of the series of Darlington pair and Sziklai pair. The layout of the proposed CE and CC amplifier occupy small areas of 158.30 μm2 (10.23×15.47 μm) and 141.16 μm2 (10.20×13.84 μm) respectively in 180 nm process technology.
- Open Access
- 13 November 2023
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 16 (42) , 3743-3755
Design and Analysis of Wideband PNP Sziklai Common Collector Amplifier with High Current Gain
Objective: Objective of the manuscript is to introduce a novel idea of designing a small-signal common collector (emitter follower) amplifier with user-defined PSpice model of PNP Sziklai pair. Method: A circuit simulation program is developed on the PSpice simulation platform to design and study the proposed amplifier circuit. Small-signal AC equivalent circuit analysis authenticates the proposed amplifier design and selection of biasing components. The proposed amplifier is also implemented on Cadence Virtuoso Simulation software at 180nm technology to validate the design by performing its layout and post-layout simulation. Findings: The proposed circuit gives high current gain and smaller gain fluctuations (β) due to environmental parameter variations. The effect of variation in stage current gain of Sziklai pair components is observed under different operating conditions. Equivalent circuit analysis, noise performance, and the effect of temperature on the performance of the proposed circuit are widely discussed. Other possible circuit structures with a similar concept of design are also discussed as special cases. Highly stable amplifier current gain as well as device current gain, high amplifier voltage gain, device voltage gains below unity, and low harmonic distortion are prime features of proposed circuit. The problem of finding a matched pair of BJTs for the Sziklai pair is also addressed in the proposed design. The linear distortion-less operation of this circuit, combined with its very high current gain, makes it a suitable candidate for instrumentation amplifiers with wide operating frequency range. The proposed amplifier takes up (10.105 x 10.055) μm2 of area at 180nm technology. The results of pre-layout and post-layout AC responses show that there is a close resemblance between the parameters before and after the layout, which promotes the usability and design of the proposed amplifier. Novelty: The idea explored in the manuscript is entirely new and first time announced by authors. Keywords: PNP Sziklai Pair, Common Collector Amplifier, Current Gain, Small Signal Amplifier, Cadence Virtuoso
- 13 November 2023
- Published by Indian Society for Education and Environment in Indian Journal of Science and Technology
- Vol. 16 (42) , 3743-3755
Open AccessDesign and Analysis of Wideband PNP Sziklai Common Collector Amplifier with High Current Gain
Objective: Objective of the manuscript is to introduce a novel idea of designing a small-signal common collector (emitter follower) amplifier with user-defined PSpice model of PNP Sziklai pair. Method: A circuit simulation program is developed on the PSpice simulation platform to design and study the proposed amplifier circuit. Small-signal AC equivalent circuit analysis authenticates the proposed amplifier design and selection of biasing components. The proposed amplifier is also implemented on Cadence Virtuoso Simulation software at 180nm technology to validate the design by performing its layout and post-layout simulation. Findings: The proposed circuit gives high current gain and smaller gain fluctuations (β) due to environmental parameter variations. The effect of variation in stage current gain of Sziklai pair components is observed under different operating conditions. Equivalent circuit analysis, noise performance, and the effect of temperature on the performance of the proposed circuit are widely discussed. Other possible circuit structures with a similar concept of design are also discussed as special cases. Highly stable amplifier current gain as well as device current gain, high amplifier voltage gain, device voltage gains below unity, and low harmonic distortion are prime features of proposed circuit. The problem of finding a matched pair of BJTs for the Sziklai pair is also addressed in the proposed design. The linear distortion-less operation of this circuit, combined with its very high current gain, makes it a suitable candidate for instrumentation amplifiers with wide operating frequency range. The proposed amplifier takes up (10.105 x 10.055) μm2 of area at 180nm technology. The results of pre-layout and post-layout AC responses show that there is a close resemblance between the parameters before and after the layout, which promotes the usability and design of the proposed amplifier. Novelty: The idea explored in the manuscript is entirely new and first time announced by authors. Keywords: PNP Sziklai Pair, Common Collector Amplifier, Current Gain, Small Signal Amplifier, Cadence Virtuoso