Francesco Morante
Francesco Morante has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Alessio Picchi
Department of Industrial Engineering (DIEF), University of Florence, Via S. Marta 3, 50139 Florence, Italy
3 shared publications - Bruno Facchini
University of Florence, IT
3 shared publications - Niccolò Castelli
University of Florence DIEF, Department of Industrial Engineering Florence 50139
2 shared publications - Tommaso Bacci
Department of Industrial Engineering (DIEF), University of Florence, 50139 Firenze, Italy
2 shared publications - Andrea Fardelli
Baker Hughes , Florence 50127, Italy
1 shared publication - Bernardo Disma Monelli
Department of Civil and Industrial Engineering, University of Pisa, Largo Lucio Lazzarino 1, 56122 Pisa, Italy
1 shared publication
Latest Publications
- Open Access
Impact of Target Surface Building Direction on the Heat Transfer Characteristics of Additive Manufactured Impingement Systems
Additive manufacturing (AM) is widely recognized as a prominent tool to maximize the potential of internal cooling systems for gas turbine applications. Several past studies have been undertaken in order to assess the effect of additive manufactured components peculiar characteristics, mainly in the form of surface roughness, on heat transfer and pressure losses. On the other hand, impingement constitutes one of the most adopted solutions for turbine vane internal cooling; also, its heat transfer performance has been shown to be potentially improved through the use of roughened target surfaces in several studies. In this work, the effect of AM-generated roughness on the performance of impingement systems has been experimentally investigated. A lumped approach was used to test additive manufactured coupons reproducing an impingement array in 1:1 scale and retrieve an average heat transfer assessment. The Laser Powder Bed Fusion (L-PBF) technique was used for the manufacturing process. As one of the main parameters affecting AM-generated roughness, the building direction of the target surface was varied in order to highlight its impact on the overall performance comparing four different building directions with a smooth reference target plate made by standard CNC machining.
Open AccessImpact of Target Surface Building Direction on the Heat Transfer Characteristics of Additive Manufactured Impingement Systems
Additive manufacturing (AM) is widely recognized as a prominent tool to maximize the potential of internal cooling systems for gas turbine applications. Several past studies have been undertaken in order to assess the effect of additive manufactured components peculiar characteristics, mainly in the form of surface roughness, on heat transfer and pressure losses. On the other hand, impingement constitutes one of the most adopted solutions for turbine vane internal cooling; also, its heat transfer performance has been shown to be potentially improved through the use of roughened target surfaces in several studies. In this work, the effect of AM-generated roughness on the performance of impingement systems has been experimentally investigated. A lumped approach was used to test additive manufactured coupons reproducing an impingement array in 1:1 scale and retrieve an average heat transfer assessment. The Laser Powder Bed Fusion (L-PBF) technique was used for the manufacturing process. As one of the main parameters affecting AM-generated roughness, the building direction of the target surface was varied in order to highlight its impact on the overall performance comparing four different building directions with a smooth reference target plate made by standard CNC machining.
- 15 October 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (3) , 1-32
Assessment of Additive Manufactured Micro-Channel Characteristics: Impact of Hydraulic Diameter Evaluation
Among internal cooling techniques for gas turbine components, skin cooling is recognized as one of the most promising, especially thanks to the spread of additive manufacturing (AM) techniques. In this regard, several studies have tried to characterize heat transfer and pressure loss performance of additive manufactured micro-channels, as well as the impact of AM characteristic parameters, mainly in the form of building angle, and resulting surface roughness and channel shape. The open literature offers several correlations in terms of friction and heat transfer coefficient using a representative hydraulic diameter. Despite that, little attention is given on the importance of such characteristic length definition which may lead to under/over estimation of the cooling rates when correlations are used in the design. In this work, coupons featuring circular micro-channels with diameters of 0.5 and 1 mm and different building angles have been tested, to retrieve pressure losses and an average heat transfer coefficient through a lumped approach. The coupons were additive manufactured using the laser powder bed fusion technique. Exploiting the experimental survey, the impact of the considered hydraulic diameter was investigated, by comparing different approaches based on a direct measurement. An additional and new approach, aimed at the identification of an “effective” diameter, based on fluid-dynamic considerations, was also considered. The data correlation and the comparison with available correlations from different authors showed the newly proposed approach to provide superior scaling capabilities and, in turn, allowing for the development of more accurate prediction methods.
- 15 October 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (3) , 1-32
Assessment of Additive Manufactured Micro-Channel Characteristics: Impact of Hydraulic Diameter Evaluation
Among internal cooling techniques for gas turbine components, skin cooling is recognized as one of the most promising, especially thanks to the spread of additive manufacturing (AM) techniques. In this regard, several studies have tried to characterize heat transfer and pressure loss performance of additive manufactured micro-channels, as well as the impact of AM characteristic parameters, mainly in the form of building angle, and resulting surface roughness and channel shape. The open literature offers several correlations in terms of friction and heat transfer coefficient using a representative hydraulic diameter. Despite that, little attention is given on the importance of such characteristic length definition which may lead to under/over estimation of the cooling rates when correlations are used in the design. In this work, coupons featuring circular micro-channels with diameters of 0.5 and 1 mm and different building angles have been tested, to retrieve pressure losses and an average heat transfer coefficient through a lumped approach. The coupons were additive manufactured using the laser powder bed fusion technique. Exploiting the experimental survey, the impact of the considered hydraulic diameter was investigated, by comparing different approaches based on a direct measurement. An additional and new approach, aimed at the identification of an “effective” diameter, based on fluid-dynamic considerations, was also considered. The data correlation and the comparison with available correlations from different authors showed the newly proposed approach to provide superior scaling capabilities and, in turn, allowing for the development of more accurate prediction methods.
- 8 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (7) , 1-11
Tuning Modal Behavior of Additively Manufactured Lattice Structures
Thanks to the increasingly widespread additive manufacturing technology and promising properties, the use of lattice structures (LS) is becoming increasingly frequent. LS allows the components to be designed with tunable stiffness, which can unlock the control of natural frequencies. However, crucial challenges must be faced to integrate LS into the typical design process. In this work, an experimental and numerical study of LS-enabled tuning of natural frequencies in mechanical components are proposed. In a first step, the difficulties arising with the large amount of finite element method (FEM) nodes, that are required to predict LS complex shapes in detail, are overcome by modeling LS with an elastic metamaterial whose stiffness properties are determined through ad hoc finite element analyses. After that, a simplified investigation can be conducted on the modal properties of components with fixed external shape and variable internal LS filling, based on triply periodic minimal surfaces (TPMS) lattices. In those conditions, the parameters of the LS core can be tuned to control and optimize the global modal frequencies of the entire geometry. In addition, the admissible range of frequencies can be estimated. Optimized plates results are validated through an experimental test campaign on additively manufactured specimens made with laser powder bed fusion technology. The samples are hammer-tested with various boundary conditions while laser sensors measure the oscillation data of selected points. Finally, estimated and identified natural frequencies were compared. The described model is suitable to be implemented in an automated tool for designers.
- 8 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (7) , 1-11
Tuning Modal Behavior of Additively Manufactured Lattice Structures
Thanks to the increasingly widespread additive manufacturing technology and promising properties, the use of lattice structures (LS) is becoming increasingly frequent. LS allows the components to be designed with tunable stiffness, which can unlock the control of natural frequencies. However, crucial challenges must be faced to integrate LS into the typical design process. In this work, an experimental and numerical study of LS-enabled tuning of natural frequencies in mechanical components are proposed. In a first step, the difficulties arising with the large amount of finite element method (FEM) nodes, that are required to predict LS complex shapes in detail, are overcome by modeling LS with an elastic metamaterial whose stiffness properties are determined through ad hoc finite element analyses. After that, a simplified investigation can be conducted on the modal properties of components with fixed external shape and variable internal LS filling, based on triply periodic minimal surfaces (TPMS) lattices. In those conditions, the parameters of the LS core can be tuned to control and optimize the global modal frequencies of the entire geometry. In addition, the admissible range of frequencies can be estimated. Optimized plates results are validated through an experimental test campaign on additively manufactured specimens made with laser powder bed fusion technology. The samples are hammer-tested with various boundary conditions while laser sensors measure the oscillation data of selected points. Finally, estimated and identified natural frequencies were compared. The described model is suitable to be implemented in an automated tool for designers.
- 16 January 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (6) , 1-17
Experimental Analysis of Additively Manufactured Latticework Coupons
The capabilities and the precision of additive manufacturing processes have been tremendously increased in the last years, and this trend is not expected to be close to an end. Researchers, in the gas turbine industry, are focusing on the technology implementation on cooling systems. The aim of the present work is to investigate the performances of eight different geometries in order to exploit the cooling potential of some challenging latticework schemes with respect to traditional ones such as smooth channel, dimples, and pin fins. Test coupons consisting of those cooling structures embedded inside a rectangular cooling channel with dimensions of 56 mm width, 5 mm height, and 68 mm length were fabricated by means of direct metal laser melting technique. Since an aim of the present work is to evaluate the shape deformation associated with this additive process, the results of the CT scan imaging technique are presented. The performances are characterized both in terms of averaged heat transfer and friction factor values inside the test coupons by means of steady-state technique with a constant wall temperature boundary condition. The investigated flow Reynolds numbers range from 18, 000 to 40, 000. These values allow the authors to provide a deeper understanding of the latticework structures performances at Reynolds numbers beyond the range typically investigated in the literature. An efficiency index is employed to compare the performances of each geometry. Although the obtained results reveal that none of the tested geometries outperforms the other ones, the latticework arrangements show a heat transfer enhancement with respect to a porosity decrease. In addition, the good capability in terms of heat transfer of the lattice structures measured in the present work suggests the use of such technologies for twofold optimization process based on mechanical resistance and heat transfer characteristics.
- 16 January 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (6) , 1-17
Experimental Analysis of Additively Manufactured Latticework Coupons
The capabilities and the precision of additive manufacturing processes have been tremendously increased in the last years, and this trend is not expected to be close to an end. Researchers, in the gas turbine industry, are focusing on the technology implementation on cooling systems. The aim of the present work is to investigate the performances of eight different geometries in order to exploit the cooling potential of some challenging latticework schemes with respect to traditional ones such as smooth channel, dimples, and pin fins. Test coupons consisting of those cooling structures embedded inside a rectangular cooling channel with dimensions of 56 mm width, 5 mm height, and 68 mm length were fabricated by means of direct metal laser melting technique. Since an aim of the present work is to evaluate the shape deformation associated with this additive process, the results of the CT scan imaging technique are presented. The performances are characterized both in terms of averaged heat transfer and friction factor values inside the test coupons by means of steady-state technique with a constant wall temperature boundary condition. The investigated flow Reynolds numbers range from 18, 000 to 40, 000. These values allow the authors to provide a deeper understanding of the latticework structures performances at Reynolds numbers beyond the range typically investigated in the literature. An efficiency index is employed to compare the performances of each geometry. Although the obtained results reveal that none of the tested geometries outperforms the other ones, the latticework arrangements show a heat transfer enhancement with respect to a porosity decrease. In addition, the good capability in terms of heat transfer of the lattice structures measured in the present work suggests the use of such technologies for twofold optimization process based on mechanical resistance and heat transfer characteristics.