Michael Pagan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Michael Pagan has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Leon M. Headings
Center for Ultrasonic Additive Manufacturing, Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W 19th Ave, Columbus, OH 43210, USA
2 shared publications - Marcelo Jorge Dapino
Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH, USA
2 shared publications - Ningxiner Zhao2 shared publications
- Steven John Zinkle
Univ. of Tennessee, Knoxville, TN (United States)
2 shared publications Aaron P. Stebner
George W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta GA 30332‐0405 USA
1 shared publication- Aida Amroussia
General Electric Global Research
1 shared publication
Latest Publications
- Open Access
- 21 August 2025
- Published by Elsevier in Food and Bioproducts Processing
- Vol. 154, 33-41
Characterizing moisture content variation in pecan kernels under cold and hot water soaking treatments
- 21 August 2025
- Published by Elsevier in Food and Bioproducts Processing
- Vol. 154, 33-41
Open AccessCharacterizing moisture content variation in pecan kernels under cold and hot water soaking treatments
- Open Access
- 20 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (4)
Porosity Reduction and Strength Increase of SS316&Cu Produced through Cold Spray Additive Manufacturing
Cold spray additive manufacturing (CSAM) is an attractive solid‐state bonding technique due to its rapid manufacturing rate and the ability to avoid deleterious effects found in solidification‐based additive manufacturing. Unfortunately, CSAM of steel components has been difficult to date to the high strength of the steel particles which resists deformation and creates interparticle porosity. Herein, it is found adding softer Cu powder particles to steel (SS316) powder and utilizing a heat treatment can decrease the porosity of the as‐sprayed structure while increasing the mechanical properties. The mixture results in an increased sprayability of the structure, as the Cu particles preferentially fill the pores, increasing the density. The microstructural evolution of the SS316 and Cu particles at the particle interfaces and interiors is investigated and reveals that the materials undergo a heterogeneous deformation route which facilitates the densification of the CSAM structure. Through annealing these components, the tensile strength increases and the density increases further. Both materials undergo microstructural recovery along with selected interdiffusion of elements which improves the metallurgical bonding. It is demonstrated that the heterogeneous deposition and microstructural evolution between the dissimilar materials can improve the overall component properties.
- 20 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (4)
Open AccessPorosity Reduction and Strength Increase of SS316&Cu Produced through Cold Spray Additive Manufacturing
Cold spray additive manufacturing (CSAM) is an attractive solid‐state bonding technique due to its rapid manufacturing rate and the ability to avoid deleterious effects found in solidification‐based additive manufacturing. Unfortunately, CSAM of steel components has been difficult to date to the high strength of the steel particles which resists deformation and creates interparticle porosity. Herein, it is found adding softer Cu powder particles to steel (SS316) powder and utilizing a heat treatment can decrease the porosity of the as‐sprayed structure while increasing the mechanical properties. The mixture results in an increased sprayability of the structure, as the Cu particles preferentially fill the pores, increasing the density. The microstructural evolution of the SS316 and Cu particles at the particle interfaces and interiors is investigated and reveals that the materials undergo a heterogeneous deformation route which facilitates the densification of the CSAM structure. Through annealing these components, the tensile strength increases and the density increases further. Both materials undergo microstructural recovery along with selected interdiffusion of elements which improves the metallurgical bonding. It is demonstrated that the heterogeneous deposition and microstructural evolution between the dissimilar materials can improve the overall component properties.
- 6 December 2023
- Published by Elsevier in Materialia
- Vol. 33
Improvements in bonding through ultrasonic additive manufacturing of titanium by stabilizing displacive phase transformations
- 6 December 2023
- Published by Elsevier in Materialia
- Vol. 33
Improvements in bonding through ultrasonic additive manufacturing of titanium by stabilizing displacive phase transformations
- 8 February 2023
- Published by Springer Nature
- p. 15-25
Corrosion and Erosion Protection to Accelerate Deployment of Sustainable Biomass
- 8 February 2023
- Published by Springer Nature
- p. 15-25
Corrosion and Erosion Protection to Accelerate Deployment of Sustainable Biomass
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Strengthening of Pre-Treated Aluminum During Ultrasonic Additive Manufacturing
Strengthening effects in materials bonded by the high strain rate plastic deformation process, Ultrasonic Additive Manufacturing (UAM), were investigated. Aluminum (Al 6061) was pre-treated by tempering and annealing prior to bonding through UAM. Following UAM, multiscale material characterization was performed. Tensile testing in the rolling (x) direction demonstrated the material became harder after the UAM process, and nanoindentation demonstrated the foil-foil interfaces became harder than the bulk foil material. The strengthening effects are a result of microstructure changes at the interfaces and in the bulk foil regions which were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy. These microstructure changes result from dynamic recrystallization, dynamic recovery, adiabatic heating, and precipitate dissolution.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessStrengthening of Pre-Treated Aluminum During Ultrasonic Additive Manufacturing
Strengthening effects in materials bonded by the high strain rate plastic deformation process, Ultrasonic Additive Manufacturing (UAM), were investigated. Aluminum (Al 6061) was pre-treated by tempering and annealing prior to bonding through UAM. Following UAM, multiscale material characterization was performed. Tensile testing in the rolling (x) direction demonstrated the material became harder after the UAM process, and nanoindentation demonstrated the foil-foil interfaces became harder than the bulk foil material. The strengthening effects are a result of microstructure changes at the interfaces and in the bulk foil regions which were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy. These microstructure changes result from dynamic recrystallization, dynamic recovery, adiabatic heating, and precipitate dissolution.