Ningxiner Zhao
Ningxiner Zhao has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Marcelo Jorge Dapino
Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH, USA
4 shared publications - Leon M. Headings
Center for Ultrasonic Additive Manufacturing, Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W 19th Ave, Columbus, OH 43210, USA
3 shared publications - Michael Pagan
George W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta GA 30332‐0405 USA
2 shared publications - Steven John Zinkle
Univ. of Tennessee, Knoxville, TN (United States)
2 shared publications - Amit Makarand Deshpande
University of Delaware
1 shared publication Andres Marquez Rossy
1 shared publication
Latest Publications
- 20 November 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 311
Analytical modeling of metal–FRP joints made by ultrasonic additive manufacturing
- 20 November 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 311
Analytical modeling of metal–FRP joints made by ultrasonic additive manufacturing
- 5 September 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 309
Comparative life cycle energy assessment of lightweight multi-material metal-fiber composite hybrid body-in-white designs
- 5 September 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 309
Comparative life cycle energy assessment of lightweight multi-material metal-fiber composite hybrid body-in-white designs
- 6 December 2023
- Published by Elsevier in Materialia
- Vol. 33
Improvements in bonding through ultrasonic additive manufacturing of titanium by stabilizing displacive phase transformations
- 6 December 2023
- Published by Elsevier in Materialia
- Vol. 33
Improvements in bonding through ultrasonic additive manufacturing of titanium by stabilizing displacive phase transformations
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Strengthening of Pre-Treated Aluminum During Ultrasonic Additive Manufacturing
Strengthening effects in materials bonded by the high strain rate plastic deformation process, Ultrasonic Additive Manufacturing (UAM), were investigated. Aluminum (Al 6061) was pre-treated by tempering and annealing prior to bonding through UAM. Following UAM, multiscale material characterization was performed. Tensile testing in the rolling (x) direction demonstrated the material became harder after the UAM process, and nanoindentation demonstrated the foil-foil interfaces became harder than the bulk foil material. The strengthening effects are a result of microstructure changes at the interfaces and in the bulk foil regions which were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy. These microstructure changes result from dynamic recrystallization, dynamic recovery, adiabatic heating, and precipitate dissolution.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessStrengthening of Pre-Treated Aluminum During Ultrasonic Additive Manufacturing
Strengthening effects in materials bonded by the high strain rate plastic deformation process, Ultrasonic Additive Manufacturing (UAM), were investigated. Aluminum (Al 6061) was pre-treated by tempering and annealing prior to bonding through UAM. Following UAM, multiscale material characterization was performed. Tensile testing in the rolling (x) direction demonstrated the material became harder after the UAM process, and nanoindentation demonstrated the foil-foil interfaces became harder than the bulk foil material. The strengthening effects are a result of microstructure changes at the interfaces and in the bulk foil regions which were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy. These microstructure changes result from dynamic recrystallization, dynamic recovery, adiabatic heating, and precipitate dissolution.