Furkan Parmaksız
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Furkan Parmaksız has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Nergizhan Anaç
Department of Mechanical Engineering, Faculty of Engineering, Zonguldak Bülent Ecevit University, Zonguldak 67100, Türkiye
6 shared publications - Oğuz Koçar
Department of Mechanical Engineering, Faculty of Engineering, Zonguldak Bülent Ecevit University, Zonguldak 67100, Türkiye
6 shared publications - Erhan Baysal
Zonguldak Bülent Ecevit Üniversitesi
2 shared publications - Ahmet Serdar Güldibi
Karabük Üniversitesi
1 shared publication - Beytullah Erdoğan
Department of Mechanical Engineering, Zonguldak Bulent Ecevit University, Zonguldak 67100, Turkey
1 shared publication Emel Mutlu
Department of Mechanical Engineering, Faculty of Engineering Zonguldak Bulent Ecevit University Zonguldak Turkey
1 shared publication
Latest Publications
- 23 December 2025
- Published by Marmara University in International Journal of Advances in Engineering and Pure Sciences
- Vol. 37 (4) , 319-336
mSLA Yöntemi ile Toz Katkılı Fotopolimer Reçine Kullanılarak Üretilen Parçaların Mekanik Özelliklerinin İncelenmesi
Stereolitografi 3D baskı işleminde bir nesnenin her katmanı, sıvı bir fotopolimer reçinenin UV ışığa maruz bırakılmasıyla oluşturulur. UV ışığının yoğunlaştığı bölgede reçineyi katılaştıran bir kimyasal reaksiyon gerçekleşir. Son zamanlarda, reçinelerin çeşitli katkı malzemeler (metal, seramik tozlar vb.) eklenerek güçlendirilmesi ile ilgili bir eğilim olmuştur. Bu çalışmada, ağırlıkça %0.5, %1 ve %1.5 dolgu oranlarında boyutları 13-20 nm Al₂O₃, 10-25 nm TiO₂ olan nanopartiküller ve 45 µm boyutunda prina, fındık kabuğu ve kenevir tozlarının katkı maddesi olarak eklendiği reçineler kullanılarak üretilen parçaların mekanik özellikleri değerlendirilmiştir. Çalışmada malzemelerin sertlik değerleri, çekme ve eğme dayanımları incelenmiştir. Sonuçlar, toz katkılı numunelerin tamamında çekme mukavemetinin referans numunelere (katkısız) göre azaldığını göstermiştir. Buna karşılık; nanopartiküller, kenevir ve prina toz katkısı bulunan bütün numunelerde eğme kuvvetinin referans numuneden yüksek olduğu, fındık tozu katkılı bütün numunelerde ise eğme kuvvetinin referans numuneden düşük olduğu görülmüştür.
- 23 December 2025
- Published by Marmara University in International Journal of Advances in Engineering and Pure Sciences
- Vol. 37 (4) , 319-336
mSLA Yöntemi ile Toz Katkılı Fotopolimer Reçine Kullanılarak Üretilen Parçaların Mekanik Özelliklerinin İncelenmesi
Stereolitografi 3D baskı işleminde bir nesnenin her katmanı, sıvı bir fotopolimer reçinenin UV ışığa maruz bırakılmasıyla oluşturulur. UV ışığının yoğunlaştığı bölgede reçineyi katılaştıran bir kimyasal reaksiyon gerçekleşir. Son zamanlarda, reçinelerin çeşitli katkı malzemeler (metal, seramik tozlar vb.) eklenerek güçlendirilmesi ile ilgili bir eğilim olmuştur. Bu çalışmada, ağırlıkça %0.5, %1 ve %1.5 dolgu oranlarında boyutları 13-20 nm Al₂O₃, 10-25 nm TiO₂ olan nanopartiküller ve 45 µm boyutunda prina, fındık kabuğu ve kenevir tozlarının katkı maddesi olarak eklendiği reçineler kullanılarak üretilen parçaların mekanik özellikleri değerlendirilmiştir. Çalışmada malzemelerin sertlik değerleri, çekme ve eğme dayanımları incelenmiştir. Sonuçlar, toz katkılı numunelerin tamamında çekme mukavemetinin referans numunelere (katkısız) göre azaldığını göstermiştir. Buna karşılık; nanopartiküller, kenevir ve prina toz katkısı bulunan bütün numunelerde eğme kuvvetinin referans numuneden yüksek olduğu, fındık tozu katkılı bütün numunelerde ise eğme kuvvetinin referans numuneden düşük olduğu görülmüştür.
- 3 December 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (4) , 1688-1702
3B YAZICIDA POLİLAKTİKASİT VE CAM FİBER KATKILI POLİPROPİLEN MALZEMELER İLE ÜRETİLEN PARÇALARIN MEKANİK PERFORMANSININ İNCELENMESİ
Bu çalışmada, üç boyutlu (3B) yazıcılarda sıklıkla kullanılan Polilaktikasit (PLA) ve cam fiber katkılı Polipropilen (PP GF30) malzemelerinin mekanik özellikleri incelenmiştir. Dört farklı doluluk oranı (%20, %50, %80 ve %100) ve üç farklı dolgu deseni (gyroid, ızgara ve üçgen) kullanılarak üretilen numunelerin çekme ve eğme testleri gerçekleştirilmiştir. Sonuçlar, PLA’nın eğme direncinin PP GF30’a göre daha yüksek olduğunu; ancak düşük doluluk oranlarında PP GF30 numunelerinin çekme dayanımının PLA’dan daha iyi sonuçlar verdiğini göstermektedir. Tam dolu (%100) numunelerde PLA çekmede daha yüksek mukavemet sergilerken, PP GF30 ise özellikle %20, %50 ve %80 doluluk oranlarında üstün performans ortaya koymuştur. Her iki malzeme için de gyroid deseni, çekme ve eğme testlerinde genellikle en iyi sonuçları vermiştir. Elde edilen bulgular, malzeme seçimi ve dolgu parametrelerinin 3B baskıyla üretilen parçaların mekanik performansı üzerindeki kritik rolünü ortaya koymaktadır.
- 3 December 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (4) , 1688-1702
3B YAZICIDA POLİLAKTİKASİT VE CAM FİBER KATKILI POLİPROPİLEN MALZEMELER İLE ÜRETİLEN PARÇALARIN MEKANİK PERFORMANSININ İNCELENMESİ
Bu çalışmada, üç boyutlu (3B) yazıcılarda sıklıkla kullanılan Polilaktikasit (PLA) ve cam fiber katkılı Polipropilen (PP GF30) malzemelerinin mekanik özellikleri incelenmiştir. Dört farklı doluluk oranı (%20, %50, %80 ve %100) ve üç farklı dolgu deseni (gyroid, ızgara ve üçgen) kullanılarak üretilen numunelerin çekme ve eğme testleri gerçekleştirilmiştir. Sonuçlar, PLA’nın eğme direncinin PP GF30’a göre daha yüksek olduğunu; ancak düşük doluluk oranlarında PP GF30 numunelerinin çekme dayanımının PLA’dan daha iyi sonuçlar verdiğini göstermektedir. Tam dolu (%100) numunelerde PLA çekmede daha yüksek mukavemet sergilerken, PP GF30 ise özellikle %20, %50 ve %80 doluluk oranlarında üstün performans ortaya koymuştur. Her iki malzeme için de gyroid deseni, çekme ve eğme testlerinde genellikle en iyi sonuçları vermiştir. Elde edilen bulgular, malzeme seçimi ve dolgu parametrelerinin 3B baskıyla üretilen parçaların mekanik performansı üzerindeki kritik rolünü ortaya koymaktadır.
- 15 July 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (3) , 837-845
3B yazıcılarda üretilmiş farklı renkli PLA malzemelerin mekanik ve optik özelliklerinin incelenmesi
3B yazdırma işlemi, popüler eklemeli imalat yöntemlerinden biridir. 3B yazıcılarda kullanılan filament malzemeleri ve eklenen katkı maddeleri (renklendiriciler, plastikleştiriciler, dolgu malzemeleri vs.) üretim sürecini, ürünün görsel, mekanik ve optik özelliklerini etkileyen unsurlardır. Bu çalışma 3B yazıcıda üretim yapan araştırmacıların ürünlerde mukavemet, renk ve yüzey yapıları (parlak, mat) arasındaki ilişkiyi anlaması için yapılmıştır. Sekiz farklı renk PLA Plus filament (beyaz, turuncu, pembe, açık mavi, kırmızı, altın sarı, siyah ve kahverengi) ile %100 doluluk oranında parçalar basılmış ve yüzey pürüzlülüğü, mekanik (çekme, eğme ve sertlik) ve optik özellikler (renk ve parlaklık) incelenmiştir. Deneylerde, en iyi çekme ve eğme mukavemeti beyaz filamentte sırasıyla 59.06 MPa ve 108.75 N olarak bulunmuştur. Bu renk malzemede en yüksek sertlik değeri (86.28 Shore D), en düşük yüzey pürüzlülüğü (2.95 µm) ve en parlak yüzey ölçülmüştür. Sonuçlar filament renklerinin mekanik özelliklerde önemli bir etkiye sahip olduğunu ve 3B yazıcı kullanıcılarının üretimde renkleri dikkate alması gerektiğini göstermektedir.
- 15 July 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (3) , 837-845
3B yazıcılarda üretilmiş farklı renkli PLA malzemelerin mekanik ve optik özelliklerinin incelenmesi
3B yazdırma işlemi, popüler eklemeli imalat yöntemlerinden biridir. 3B yazıcılarda kullanılan filament malzemeleri ve eklenen katkı maddeleri (renklendiriciler, plastikleştiriciler, dolgu malzemeleri vs.) üretim sürecini, ürünün görsel, mekanik ve optik özelliklerini etkileyen unsurlardır. Bu çalışma 3B yazıcıda üretim yapan araştırmacıların ürünlerde mukavemet, renk ve yüzey yapıları (parlak, mat) arasındaki ilişkiyi anlaması için yapılmıştır. Sekiz farklı renk PLA Plus filament (beyaz, turuncu, pembe, açık mavi, kırmızı, altın sarı, siyah ve kahverengi) ile %100 doluluk oranında parçalar basılmış ve yüzey pürüzlülüğü, mekanik (çekme, eğme ve sertlik) ve optik özellikler (renk ve parlaklık) incelenmiştir. Deneylerde, en iyi çekme ve eğme mukavemeti beyaz filamentte sırasıyla 59.06 MPa ve 108.75 N olarak bulunmuştur. Bu renk malzemede en yüksek sertlik değeri (86.28 Shore D), en düşük yüzey pürüzlülüğü (2.95 µm) ve en parlak yüzey ölçülmüştür. Sonuçlar filament renklerinin mekanik özelliklerde önemli bir etkiye sahip olduğunu ve 3B yazıcı kullanıcılarının üretimde renkleri dikkate alması gerektiğini göstermektedir.
- Open Access
- 20 March 2025
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 13 (1) , 234-249
CAM FİBER TAKVİYELİ PLASTİK MALZEMELERİN DELAMİNASYON DURUMUNUN İNCELENMESİ
Cam fiber malzemeler ekonomikliği ve hafif olması sebebiyle endüstride geniş bir uygulama alanına sahiptir. Cam fiber kompozit malzemelerin mekanik özelliklerinin ve montaj sırasında oluşabilecek olası hasar mekanizmalarının (delik delmede delaminasyon gibi) bilinmesi tasarımcılar için önemlidir. Bu çalışmada farklı imalat teknikleriyle üretilmiş (sıcak presle kalıplama, 3B baskı ve elle yatırma) cam elyaf takviyeli plastiklerde (CTP) delik delme işleminden sonra oluşan delik çıkış hasarları incelenmiştir. Deneylerde işlem parametreleri olarak üç farklı ilerleme hızı (200, 400 ve 600 mm/dak) ve iki farklı takım dönme hızı (1500 ve 3000 dev/dak) kullanılmıştır. Delik delme işlemi sonunda delaminasyon oranları hesaplanmıştır. En düşük ve en yüksek delaminasyon oranına sahip deney numunelerinin görsel muayeneleri yapılmıştır. Ek olarak, 3B yazıcıda delikli olarak basılmış ve sonradan matkapla delinmiş iki ayrı CTP malzemenin delik delme işlemi karşılaştırılmıştır. Sıcak presle kalıplama tekniği ile üretilen parçalarda takım ilerleme hızı artarken delaminasyon oranı artmış, 3B baskı tekniği ile üretilen parçalarda ilerleme hızının artmasıyla delaminasyon oranı düşmüştür. Elle yatırma tekniği ile üretilen parçalarda ise düşük takım dönme hızlarında delaminasyon oranının arttığı belirlenmiştir. Ayrıca delaminasyonda işlem parametrelerinin etkisi kadar malzeme üretim tekniğinin de etkili olduğu görülmüştür. Sıcak presle kalıplama ve elle yatırma tekniğiyle üretilen cam elyaf takviyeli kompozitlerde delik delme işlem parametrelerinin delaminasyona etkileri benzerken, 3B yazıcı ile üretilmiş parçalar farklı davranış sergilemiştir.
- 20 March 2025
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 13 (1) , 234-249
Open AccessCAM FİBER TAKVİYELİ PLASTİK MALZEMELERİN DELAMİNASYON DURUMUNUN İNCELENMESİ
Cam fiber malzemeler ekonomikliği ve hafif olması sebebiyle endüstride geniş bir uygulama alanına sahiptir. Cam fiber kompozit malzemelerin mekanik özelliklerinin ve montaj sırasında oluşabilecek olası hasar mekanizmalarının (delik delmede delaminasyon gibi) bilinmesi tasarımcılar için önemlidir. Bu çalışmada farklı imalat teknikleriyle üretilmiş (sıcak presle kalıplama, 3B baskı ve elle yatırma) cam elyaf takviyeli plastiklerde (CTP) delik delme işleminden sonra oluşan delik çıkış hasarları incelenmiştir. Deneylerde işlem parametreleri olarak üç farklı ilerleme hızı (200, 400 ve 600 mm/dak) ve iki farklı takım dönme hızı (1500 ve 3000 dev/dak) kullanılmıştır. Delik delme işlemi sonunda delaminasyon oranları hesaplanmıştır. En düşük ve en yüksek delaminasyon oranına sahip deney numunelerinin görsel muayeneleri yapılmıştır. Ek olarak, 3B yazıcıda delikli olarak basılmış ve sonradan matkapla delinmiş iki ayrı CTP malzemenin delik delme işlemi karşılaştırılmıştır. Sıcak presle kalıplama tekniği ile üretilen parçalarda takım ilerleme hızı artarken delaminasyon oranı artmış, 3B baskı tekniği ile üretilen parçalarda ilerleme hızının artmasıyla delaminasyon oranı düşmüştür. Elle yatırma tekniği ile üretilen parçalarda ise düşük takım dönme hızlarında delaminasyon oranının arttığı belirlenmiştir. Ayrıca delaminasyonda işlem parametrelerinin etkisi kadar malzeme üretim tekniğinin de etkili olduğu görülmüştür. Sıcak presle kalıplama ve elle yatırma tekniğiyle üretilen cam elyaf takviyeli kompozitlerde delik delme işlem parametrelerinin delaminasyona etkileri benzerken, 3B yazıcı ile üretilmiş parçalar farklı davranış sergilemiştir.
- 22 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10526-10541
Effect of process parameters on the weld quality of 3D printed PLA‐CF sheets by FSW process
Friction stir welding (FSW) process is commonly used in the joining of similar/dissimilar materials. FSW involves process parameters that can affect the weld quality. To enhance this, it is important to accurately determine the process parameters. In this study, the weldability of 3D printed carbon fiber‐reinforced polylactic acid (PLA‐CF) sheets has been investigated using FSW. The process was carried out with three different tool pin geometries (triangle, square, and screw), feed rates (20, 40, and 60 mm/min) and tool rotational speeds (1250, 1750, and 2250 rpm). Tensile tests were conducted and hardness measurements were taken to discuss the effects of process parameters on weld quality. Temperature values were measured to examine the impact of tool pin geometry on the heat generation during welding. Finally, visual and microstructure examinations were conducted in the weld zone to assess the changes in weld strength. As a result, it has been determined that weld strength is significantly influenced by the process parameters. Accordingly, the best weld quality was achieved with triangular pin profile at a traverse speed of 40 mm/min and a rotation speed of 1250 rpm (UTS: 43.6 MPa, efficiency 79.6%), while for square pin (UTS: 49.2 MPa, efficiency 89.8%) and screw pin (UTS: 44.9 MPa, efficiency 81.9%) geometries, the optimal values are 20 mm/min and 2250 rpm. The distribution of CF reinforcement is uniform in high weld strength samples, while with lower weld quality samples, the distribution is irregular. This indicates that the reinforcement of CF has significant effect on weld strength.Highlights: Investigate the weldability of 3D printed PLA‐CF plates through FSW process. Examines the impact of pin geometry, feed rates, and tool rotational speeds. Determine the welding strength and temperature generated during welding. Choice of the square pin geometry is more suitable for joining PLA‐CF plates. Visual and microstructure examinations were conducted in the weld zone.
- 22 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10526-10541
Effect of process parameters on the weld quality of 3D printed PLA‐CF sheets by FSW process
Friction stir welding (FSW) process is commonly used in the joining of similar/dissimilar materials. FSW involves process parameters that can affect the weld quality. To enhance this, it is important to accurately determine the process parameters. In this study, the weldability of 3D printed carbon fiber‐reinforced polylactic acid (PLA‐CF) sheets has been investigated using FSW. The process was carried out with three different tool pin geometries (triangle, square, and screw), feed rates (20, 40, and 60 mm/min) and tool rotational speeds (1250, 1750, and 2250 rpm). Tensile tests were conducted and hardness measurements were taken to discuss the effects of process parameters on weld quality. Temperature values were measured to examine the impact of tool pin geometry on the heat generation during welding. Finally, visual and microstructure examinations were conducted in the weld zone to assess the changes in weld strength. As a result, it has been determined that weld strength is significantly influenced by the process parameters. Accordingly, the best weld quality was achieved with triangular pin profile at a traverse speed of 40 mm/min and a rotation speed of 1250 rpm (UTS: 43.6 MPa, efficiency 79.6%), while for square pin (UTS: 49.2 MPa, efficiency 89.8%) and screw pin (UTS: 44.9 MPa, efficiency 81.9%) geometries, the optimal values are 20 mm/min and 2250 rpm. The distribution of CF reinforcement is uniform in high weld strength samples, while with lower weld quality samples, the distribution is irregular. This indicates that the reinforcement of CF has significant effect on weld strength.Highlights: Investigate the weldability of 3D printed PLA‐CF plates through FSW process. Examines the impact of pin geometry, feed rates, and tool rotational speeds. Determine the welding strength and temperature generated during welding. Choice of the square pin geometry is more suitable for joining PLA‐CF plates. Visual and microstructure examinations were conducted in the weld zone.
- Open Access
Investigation of Mechanical Properties and Color Changes of 3D-Printed Parts with Different Infill Ratios and Colors After Aging
Since their inception, plastics have become indispensable materials. However, plastics used for extended periods in industrial applications are prone to aging, which negatively impacts their material behavior and performance. To ensure the long-term usability of these materials, they must be tested in real-time, in-service environments to assess degradation. In practice, however, accelerated aging techniques are commonly employed to avoid time loss. Over time, various indicators of degradation in plastics emerge, such as changes in molecular weight, cracking, and mechanical properties like strain at break and impact strength. Among these, color deterioration or change is a critical factor that helps evaluate the service life of these materials. Considering the increasing use of plastics in 3D printing today, and the growing focus on strength over aesthetics in these applications, it is particularly useful to evaluate aging in plastics based on the relationship between color and strength. The wide application of 3D printing in various industries necessitates understanding material properties under aging conditions. This study examines the effects of aging on the mechanical behavior of polylactic acid (PLA) with three different colors (yellow, orange, and red) and three different infill ratios (20%, 60%, and 100%). The samples underwent an accelerated aging process of 432 h, which included 8 h of UV radiation, 15 min of water spraying, followed by 3 h and 45 min with the UV lamps turned off. Tensile tests, bending tests, hardness measurements, and color evaluations were conducted on the samples, linking the color changes after aging with the materials’ mechanical properties. The results show that after aging, yellow samples with a 100% infill ratio exhibited a 6.9% increase in tensile strength (44.50 MPa to 47.58 MPa). Orange samples with a 100% infill ratio were less affected by aging, while red samples experienced a decrease in tensile strength across all infill ratios. Regarding bending force, increases were observed in the orange, yellow, and red samples by 10.37%, 25.05%, and 8.87%, respectively. This study underscores the importance of color selection when designing 3D-printed materials for long-term applications.
Open AccessInvestigation of Mechanical Properties and Color Changes of 3D-Printed Parts with Different Infill Ratios and Colors After Aging
Since their inception, plastics have become indispensable materials. However, plastics used for extended periods in industrial applications are prone to aging, which negatively impacts their material behavior and performance. To ensure the long-term usability of these materials, they must be tested in real-time, in-service environments to assess degradation. In practice, however, accelerated aging techniques are commonly employed to avoid time loss. Over time, various indicators of degradation in plastics emerge, such as changes in molecular weight, cracking, and mechanical properties like strain at break and impact strength. Among these, color deterioration or change is a critical factor that helps evaluate the service life of these materials. Considering the increasing use of plastics in 3D printing today, and the growing focus on strength over aesthetics in these applications, it is particularly useful to evaluate aging in plastics based on the relationship between color and strength. The wide application of 3D printing in various industries necessitates understanding material properties under aging conditions. This study examines the effects of aging on the mechanical behavior of polylactic acid (PLA) with three different colors (yellow, orange, and red) and three different infill ratios (20%, 60%, and 100%). The samples underwent an accelerated aging process of 432 h, which included 8 h of UV radiation, 15 min of water spraying, followed by 3 h and 45 min with the UV lamps turned off. Tensile tests, bending tests, hardness measurements, and color evaluations were conducted on the samples, linking the color changes after aging with the materials’ mechanical properties. The results show that after aging, yellow samples with a 100% infill ratio exhibited a 6.9% increase in tensile strength (44.50 MPa to 47.58 MPa). Orange samples with a 100% infill ratio were less affected by aging, while red samples experienced a decrease in tensile strength across all infill ratios. Regarding bending force, increases were observed in the orange, yellow, and red samples by 10.37%, 25.05%, and 8.87%, respectively. This study underscores the importance of color selection when designing 3D-printed materials for long-term applications.
- Open Access
- 15 December 2023
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 7 (3) , 146-156
Investigation of mechanical properties and thermal conductivity coefficients of 3D printer materials
The demand for 3D printer technology and products, one of the additive manufacturing methods, is increasing daily in the sectoral and academic fields. Many types of polymer-based filaments are used in 3D printers, pure or filled/reinforcement. Utilizing these specialized materials in places suitable for their mechanical and thermal properties will help efficiently use resources. Using 3D printers, it is possible to manufacture products that provide thermal insulation or good heat conduction in heating and cooling areas. Especially due to the energy requirements for heating and cooling, it is very important to know the thermal performance of materials to ensure and maintain energy efficiency. This study experimentally investigated the mechanical properties and heat conduction coefficients of 3D printed parts. The experiments were conducted with seven different filament materials (PLA, PLA+, PLA-CF, PLA Wood, Tough PLA, ABS+, TPU) and three layer thicknesses (0.1, 0.2, and 0.3 mm). Samples for tensile testing, hardness, and thermal conductivity coefficient measurements were produced, and measurements were performed. In the experiments, the highest tensile strength was obtained in PLA-CF with 0.3 mm layer thickness, and the lowest tensile strength was obtained in PLA Wood with 0.3 mm layer thickness. Tensile strength decreased with an increasing layer thickness in PLA, PLA Wood, ABS+, and TPU, while it increased in PLA-CF. The highest tensile strength of PLA+ was determined to be 0.2 mm and 0.1 mm layer thickness in Tough PLA. Hardness results showed minimal change in hardness values with increasing layer thickness. The thermal conductivity values of the samples varied according to the additives and layer thicknesses. The highest thermal conductivity increase was measured in PLA-CF with 11.84%, and the lowest thermal conductivity decrease was measured in Tough PLA with 9.44%.
- 15 December 2023
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 7 (3) , 146-156
Open AccessInvestigation of mechanical properties and thermal conductivity coefficients of 3D printer materials
The demand for 3D printer technology and products, one of the additive manufacturing methods, is increasing daily in the sectoral and academic fields. Many types of polymer-based filaments are used in 3D printers, pure or filled/reinforcement. Utilizing these specialized materials in places suitable for their mechanical and thermal properties will help efficiently use resources. Using 3D printers, it is possible to manufacture products that provide thermal insulation or good heat conduction in heating and cooling areas. Especially due to the energy requirements for heating and cooling, it is very important to know the thermal performance of materials to ensure and maintain energy efficiency. This study experimentally investigated the mechanical properties and heat conduction coefficients of 3D printed parts. The experiments were conducted with seven different filament materials (PLA, PLA+, PLA-CF, PLA Wood, Tough PLA, ABS+, TPU) and three layer thicknesses (0.1, 0.2, and 0.3 mm). Samples for tensile testing, hardness, and thermal conductivity coefficient measurements were produced, and measurements were performed. In the experiments, the highest tensile strength was obtained in PLA-CF with 0.3 mm layer thickness, and the lowest tensile strength was obtained in PLA Wood with 0.3 mm layer thickness. Tensile strength decreased with an increasing layer thickness in PLA, PLA Wood, ABS+, and TPU, while it increased in PLA-CF. The highest tensile strength of PLA+ was determined to be 0.2 mm and 0.1 mm layer thickness in Tough PLA. Hardness results showed minimal change in hardness values with increasing layer thickness. The thermal conductivity values of the samples varied according to the additives and layer thicknesses. The highest thermal conductivity increase was measured in PLA-CF with 11.84%, and the lowest thermal conductivity decrease was measured in Tough PLA with 9.44%.