Dan Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dan Wang has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Bing Zhang
9 shared publications- Huishan Shang
School of Chemical Engineering, Zhengzhou University, Zhengzhou 450001, P. R. China
9 shared publications - Yafei Zhao
School of Chemical Engineering, Zhengzhou University, Zhengzhou 450001, China
8 shared publications - Bing Zhang
School of Chemical Engineering
6 shared publications Yafei Zhao
6 shared publications- Haijun Zhang
Dalian Institute of Chemical Physics, Chinese Academy of Sciences
5 shared publications
Latest Publications
- 14 May 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (20) , 9665-9679
Phase-Change-Gated Catalytic System with On-Demand Switchable Activity and Integrated Thermal Management
- 14 May 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (20) , 9665-9679
Phase-Change-Gated Catalytic System with On-Demand Switchable Activity and Integrated Thermal Management
- 6 March 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (11) , 5779-5790
Simultaneous Nanoconfinement and Catalysis in a Metal–Halloysite Hybrid Sponge for Accelerated and Clean Hydrogen Production from Ammonia Borane
- 6 March 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (11) , 5779-5790
Simultaneous Nanoconfinement and Catalysis in a Metal–Halloysite Hybrid Sponge for Accelerated and Clean Hydrogen Production from Ammonia Borane
- 22 January 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (8) , 3885-3898
Synergistic Cu/CeO 2 /Halloysite Nanotube Catalysts for Temperature-Programmable Biomass Valorization
- 22 January 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (8) , 3885-3898
Synergistic Cu/CeO 2 /Halloysite Nanotube Catalysts for Temperature-Programmable Biomass Valorization
- 6 January 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1037, 71-77
Comparison of Two Typical Adhesive Fracture Mechanics Considering Hygrothermal Aging
Carbon fiber reinforced polymer (CFRP) bonded structures are widely used for their lightweight and high specific strength. However, research on durability of adhesively bonded lap joints under hygrothermal conditions remain insufficient. Therefore, the aging process and residual strength of CFRP-bonded lap joints with different adhesives were studied. Condition of hygrothermal aging tests were set, then moisture absorption behavior of CFRP plate and adhesive layer were analyzed, respectively. Based on the same aging period, residual tensile strength of acrylic-based specimens and epoxy-based specimens were compared. To evaluate their performance and clarify the failure mechanisms, Finite element method (FEM) simulations were conducted. Load-displacement curve was recorded and morphology of the failure surfaces was analyzed by using a microscope.
- 6 January 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1037, 71-77
Comparison of Two Typical Adhesive Fracture Mechanics Considering Hygrothermal Aging
Carbon fiber reinforced polymer (CFRP) bonded structures are widely used for their lightweight and high specific strength. However, research on durability of adhesively bonded lap joints under hygrothermal conditions remain insufficient. Therefore, the aging process and residual strength of CFRP-bonded lap joints with different adhesives were studied. Condition of hygrothermal aging tests were set, then moisture absorption behavior of CFRP plate and adhesive layer were analyzed, respectively. Based on the same aging period, residual tensile strength of acrylic-based specimens and epoxy-based specimens were compared. To evaluate their performance and clarify the failure mechanisms, Finite element method (FEM) simulations were conducted. Load-displacement curve was recorded and morphology of the failure surfaces was analyzed by using a microscope.
- 6 January 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1037, 79-92
Fracture Risk Modeling in Pyrolyzed Phenolic Resin: Microstructure Prediction and Stress Concentration Factor Evolution via CNN-CVAE and FEM
The microstructure of phenolic resin undergoes significant transformation under high-temperature pyrolysis, affecting its mechanical performance and fracture behavior. By combining Convolutional Neural Networks (CNN) and Conditional Variational Autoencoders (CVAE), a generative modeling framework was proposed. Then its suitability to predict microstructure evolution of phenolic resin under varying pyrolysis temperatures was studied. Finite Element Method (FEM) simulations were conducted to analyze stress distributions. Results indicate a significant increase in the area of high stress concentration zones with rising pyrolysis temperature, with pore bridges, sharp edges, and clustered porosity identified as potential fracture initiation sites.
- 6 January 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1037, 79-92
Fracture Risk Modeling in Pyrolyzed Phenolic Resin: Microstructure Prediction and Stress Concentration Factor Evolution via CNN-CVAE and FEM
The microstructure of phenolic resin undergoes significant transformation under high-temperature pyrolysis, affecting its mechanical performance and fracture behavior. By combining Convolutional Neural Networks (CNN) and Conditional Variational Autoencoders (CVAE), a generative modeling framework was proposed. Then its suitability to predict microstructure evolution of phenolic resin under varying pyrolysis temperatures was studied. Finite Element Method (FEM) simulations were conducted to analyze stress distributions. Results indicate a significant increase in the area of high stress concentration zones with rising pyrolysis temperature, with pore bridges, sharp edges, and clustered porosity identified as potential fracture initiation sites.
- 12 December 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1036, 127-138
Research on Fracture Mechanics of Non-Reciprocal Adhesive in Composite Single-Lap Bonded Joints Based on UEL
Single-lap bonded joints are widely used in aerospace, shipbuilding, and other fields due to their advantages, such as light weight, high specific strength, and no stress concentration caused by hole-making or spot-welding. However, the traditional methods of increasing geometric parameters, such as lap length to improve strength, have limitations in scenarios where the bonding area is restricted. To solve this problem, in this study, it is assumed that carbon fibers with a volume fraction of 10% were introduced into the epoxy adhesive layer and arranged in a 45° orientation. The mechanical non-reciprocity was achieved by utilizing the difference in tensile and compressive moduli. A non-reciprocal cohesive fracture mechanics model of the composite single-lap joint structure based on the User-defined Element (UEL) was established to explore the effect of non-reciprocity on the bonding strength. The results show that the non-reciprocal adhesive layer effectively suppresses the peeling stress concentration at the cohesive failure interface of the adhesive layer, increasing the tensile strength of the single-lap bonded joint by approximately 6.27% compared to the traditional homogeneous adhesive layer, verifying the effectiveness of the model. This research breaks through the limitations of traditional geometric parameter optimization. It can specifically regulate the interfacial stress distribution without changing the bonding area, providing a new material design idea for strength optimization in scenarios where the bonding area is restricted, such as in aerospace. It has important theoretical significance and engineering application prospects.
- 12 December 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1036, 127-138
Research on Fracture Mechanics of Non-Reciprocal Adhesive in Composite Single-Lap Bonded Joints Based on UEL
Single-lap bonded joints are widely used in aerospace, shipbuilding, and other fields due to their advantages, such as light weight, high specific strength, and no stress concentration caused by hole-making or spot-welding. However, the traditional methods of increasing geometric parameters, such as lap length to improve strength, have limitations in scenarios where the bonding area is restricted. To solve this problem, in this study, it is assumed that carbon fibers with a volume fraction of 10% were introduced into the epoxy adhesive layer and arranged in a 45° orientation. The mechanical non-reciprocity was achieved by utilizing the difference in tensile and compressive moduli. A non-reciprocal cohesive fracture mechanics model of the composite single-lap joint structure based on the User-defined Element (UEL) was established to explore the effect of non-reciprocity on the bonding strength. The results show that the non-reciprocal adhesive layer effectively suppresses the peeling stress concentration at the cohesive failure interface of the adhesive layer, increasing the tensile strength of the single-lap bonded joint by approximately 6.27% compared to the traditional homogeneous adhesive layer, verifying the effectiveness of the model. This research breaks through the limitations of traditional geometric parameter optimization. It can specifically regulate the interfacial stress distribution without changing the bonding area, providing a new material design idea for strength optimization in scenarios where the bonding area is restricted, such as in aerospace. It has important theoretical significance and engineering application prospects.
- 12 December 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1036, 115-125
Study on Strength Optimization of CFRP Single-Lap Joints Based on Local Pre-Curing Effect
The early failure of single-lap adhesive joints in carbon fiber reinforced polymer (CFRP) composites is typically induced by stress concentration at the edges of the overlap region. To address this issue, this study proposes a novel local pre-curing process system based on gradient thermal curing regulation. Through multi-physical field modeling of the temperature-curing coupling effect and a gradient curing control strategy, active optimization of the adhesive layer stress distribution is achieved. By optimizing the interface stress distribution, the proposed technique demonstrates the potential to enhance the overall joint performance by 3-6%. This research combines Abaqus finite element simulation and experimental verification. A CFRP single-lap joint model considering the temperature-curing coupling effect was established to analyze the influence of local pre-curing on the stress distribution of the adhesive layer. The results show that: 1. Local pre-curing can reduce the peel stress in the critical edge danger zone by about 3 - 5% while improving the shear strength in the middle region. 2. The preferential curing at the center of the adhesive layer can induce stress redistribution, relieve the stress concentration at the edges, and thus improve the overall load-bearing capacity of the joint. This study provides a low-cost and easily implementable solution for optimizing the performance of CFRP joints, showing potential applications in the field of lightweight aerospace structures. Through the synergistic effect of precise thermal management and regulation of the adhesive's rheological properties, it offers new insights for advanced composite joining technologies.
- 12 December 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1036, 115-125
Study on Strength Optimization of CFRP Single-Lap Joints Based on Local Pre-Curing Effect
The early failure of single-lap adhesive joints in carbon fiber reinforced polymer (CFRP) composites is typically induced by stress concentration at the edges of the overlap region. To address this issue, this study proposes a novel local pre-curing process system based on gradient thermal curing regulation. Through multi-physical field modeling of the temperature-curing coupling effect and a gradient curing control strategy, active optimization of the adhesive layer stress distribution is achieved. By optimizing the interface stress distribution, the proposed technique demonstrates the potential to enhance the overall joint performance by 3-6%. This research combines Abaqus finite element simulation and experimental verification. A CFRP single-lap joint model considering the temperature-curing coupling effect was established to analyze the influence of local pre-curing on the stress distribution of the adhesive layer. The results show that: 1. Local pre-curing can reduce the peel stress in the critical edge danger zone by about 3 - 5% while improving the shear strength in the middle region. 2. The preferential curing at the center of the adhesive layer can induce stress redistribution, relieve the stress concentration at the edges, and thus improve the overall load-bearing capacity of the joint. This study provides a low-cost and easily implementable solution for optimizing the performance of CFRP joints, showing potential applications in the field of lightweight aerospace structures. Through the synergistic effect of precise thermal management and regulation of the adhesive's rheological properties, it offers new insights for advanced composite joining technologies.
- 25 September 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (6)
Ultrahigh-stability Co3O4/CuO hetero-nanoarrays with multi-oriented architecture for cascade nitrate reduction in neutral media
- 25 September 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (6)
Ultrahigh-stability Co3O4/CuO hetero-nanoarrays with multi-oriented architecture for cascade nitrate reduction in neutral media