Elif Işık
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Elif Işık has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Aleyna Taşkın
Ondokuz Mayis Üniversitesi
6 shared publications - Mahmut Can Şenel
Ondokuz Mayis Üniversitesi
6 shared publications - Betül Kafkaslıoğlu Yıldız
Faculty of Engineering and Natural Sciences, Metallurgical and Materials Engineering Department, Sivas University of Science and Technology, Sivas, Turkey
2 shared publications - Ali Suat Yıldız
Sivas University of Science and Technology
1 shared publication - Seda Taşdemi̇r
Sivas Bilim ve Teknoloji Universitesi
1 shared publication - Yahya Kemal Tür
Department of Materials Science and Engineering Gebze Technical University Darıca Kocaeli Turkey
1 shared publication
Latest Publications
- Open Access
- 16 June 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (3) , 1314-1332
Al7075-B4C Kompozitlerin Tribolojik Özelliklerinin ve Mikroyapısının İncelenmesi
Bu çalışmada, Al7075 matrisli B4C takviyeli kompozitler toz metalürjisi ve sıcak presleme yöntemleri ile üretilmiştir. Al7075 matrise ağırlıkça %1, 3, 6, 9, 12, 15 ve 30 oranlarında B4C ilave edilmiştir. Üretilen kompozitlerin deneysel yoğunluğu, Vickers sertliği, aşınma oranı ve sürtünme katsayısı belirlenmiştir. Elde edilen sonuçlara göre en yüksek deneysel yoğunluk (2,63 g/cm3), Vickers sertliği (226 HV) ile en düşük aşınma oranı ((0,000091 mm3/(Nm)), kütle kaybı (0,0012 g) ve sürtünme katsayısı (0,4) Al7075-30B4C kompozitte elde edilmiştir. Ayrıca yapılan mikroyapı analizleri ile bu kompozitte mikroyapının daha yoğun olduğu gözlemlenmiştir. Çalışma sonucunda Al7075 alaşımına belirli katkı oranında (ağırlıkça %30) B4C ilave edildiğinde kompozitin mikroyapısının ve tribolojik özelliklerinin iyileştiği tespit edilmiştir.
- 16 June 2025
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 8 (3) , 1314-1332
Open AccessAl7075-B4C Kompozitlerin Tribolojik Özelliklerinin ve Mikroyapısının İncelenmesi
Bu çalışmada, Al7075 matrisli B4C takviyeli kompozitler toz metalürjisi ve sıcak presleme yöntemleri ile üretilmiştir. Al7075 matrise ağırlıkça %1, 3, 6, 9, 12, 15 ve 30 oranlarında B4C ilave edilmiştir. Üretilen kompozitlerin deneysel yoğunluğu, Vickers sertliği, aşınma oranı ve sürtünme katsayısı belirlenmiştir. Elde edilen sonuçlara göre en yüksek deneysel yoğunluk (2,63 g/cm3), Vickers sertliği (226 HV) ile en düşük aşınma oranı ((0,000091 mm3/(Nm)), kütle kaybı (0,0012 g) ve sürtünme katsayısı (0,4) Al7075-30B4C kompozitte elde edilmiştir. Ayrıca yapılan mikroyapı analizleri ile bu kompozitte mikroyapının daha yoğun olduğu gözlemlenmiştir. Çalışma sonucunda Al7075 alaşımına belirli katkı oranında (ağırlıkça %30) B4C ilave edildiğinde kompozitin mikroyapısının ve tribolojik özelliklerinin iyileştiği tespit edilmiştir.
- Open Access
- 15 April 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (2) , 482-489
Si3N4 katkılı Al7075 matrisli kompozitlerin mikroyapısının ve tribolojik özelliklerinin incelenmesi
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise ağırlıkça %1, 3, 6, 9 ve 12 katkı oranlarında Si3N4 ilave edilerek kompozit malzemeler üretilmiştir. Üretilen kompozitlere yoğunluk, Vickers sertliği, aşınma ve sürtünme testleri uygulanmıştır. Ayrıca kompozitlerin mikroyapılarını incelemek amacıyla XRD, SEM ve SEM-EDX analizleri yapılmıştır. Sonuç olarak en yüksek deneysel yoğunluk (2.65 g/cm3), en yüksek Vickers sertliği (205 HV), en düşük aşınma oranı (0.00018 mm3/(Nm)), en düşük kütle kaybı (0.0025 g) ve en düşük sürtünme katsayısı (0.38) değerleri Al7075-%9 Si3N4 kompozitte elde edilmiştir. Ancak ağırlıkça %12 Si3N4 katkı oranında takviye partiküllerinin topaklanmasından dolayı kompozitin tribolojik özellikleri kötüleşmiştir. Sonuç olarak Al7075 matrise %9 Si3N4 katkısının kompozitin tribolojik özelliklerini iyileştirdiği tespit edilmiştir.
- 15 April 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (2) , 482-489
Open AccessSi3N4 katkılı Al7075 matrisli kompozitlerin mikroyapısının ve tribolojik özelliklerinin incelenmesi
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise ağırlıkça %1, 3, 6, 9 ve 12 katkı oranlarında Si3N4 ilave edilerek kompozit malzemeler üretilmiştir. Üretilen kompozitlere yoğunluk, Vickers sertliği, aşınma ve sürtünme testleri uygulanmıştır. Ayrıca kompozitlerin mikroyapılarını incelemek amacıyla XRD, SEM ve SEM-EDX analizleri yapılmıştır. Sonuç olarak en yüksek deneysel yoğunluk (2.65 g/cm3), en yüksek Vickers sertliği (205 HV), en düşük aşınma oranı (0.00018 mm3/(Nm)), en düşük kütle kaybı (0.0025 g) ve en düşük sürtünme katsayısı (0.38) değerleri Al7075-%9 Si3N4 kompozitte elde edilmiştir. Ancak ağırlıkça %12 Si3N4 katkı oranında takviye partiküllerinin topaklanmasından dolayı kompozitin tribolojik özellikleri kötüleşmiştir. Sonuç olarak Al7075 matrise %9 Si3N4 katkısının kompozitin tribolojik özelliklerini iyileştirdiği tespit edilmiştir.
- 7 April 2025
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- No. 718,p. 1-22
Toz Metalürjisi ve Sıcak Preslemeyle Üretilen Al7075-Si3N4 Kompozitlerin Mikroyapısının ve Mekanik Özelliklerinin İncelenmesi
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise farklı oranlarda (ağırlıkça %1, 3, 6, 9 ve 12) Si3N4 takviye edilmiştir. Katkı oranının üretilen kompozitlerin mikroyapılarına ve mekanik özelliklerine (yoğunluk, gözeneklilik oranı, Vickers sertliği ve basma dayanımı) olan etkisi incelenmiştir. Yapılan testler sonucunda en yüksek yoğunluk (2,65 g/cm3), Vickers sertliği (205 HV), basma dayanımı (344 MPa) ve en düşük gözeneklilik oranı (%7,5) Al7075-9Si3N4 kompozitte elde edilmiştir. Mikroyapı incelemeleri sonucunda ise %9Si3N4 katkı oranında takviye partiküllerinin matris içerisinde homojene yakın bir şekilde dağıldığı belirlenmiştir. Sonuç olarak Al7075 matrise %9Si3N4 katkısının kompozitin mikroyapısını yoğunlaştırdığı ve mekanik özelliklerini iyileştirdiği tespit edilmiştir.
- 7 April 2025
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- No. 718,p. 1-22
Toz Metalürjisi ve Sıcak Preslemeyle Üretilen Al7075-Si3N4 Kompozitlerin Mikroyapısının ve Mekanik Özelliklerinin İncelenmesi
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise farklı oranlarda (ağırlıkça %1, 3, 6, 9 ve 12) Si3N4 takviye edilmiştir. Katkı oranının üretilen kompozitlerin mikroyapılarına ve mekanik özelliklerine (yoğunluk, gözeneklilik oranı, Vickers sertliği ve basma dayanımı) olan etkisi incelenmiştir. Yapılan testler sonucunda en yüksek yoğunluk (2,65 g/cm3), Vickers sertliği (205 HV), basma dayanımı (344 MPa) ve en düşük gözeneklilik oranı (%7,5) Al7075-9Si3N4 kompozitte elde edilmiştir. Mikroyapı incelemeleri sonucunda ise %9Si3N4 katkı oranında takviye partiküllerinin matris içerisinde homojene yakın bir şekilde dağıldığı belirlenmiştir. Sonuç olarak Al7075 matrise %9Si3N4 katkısının kompozitin mikroyapısını yoğunlaştırdığı ve mekanik özelliklerini iyileştirdiği tespit edilmiştir.
- Open Access
- 3 March 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (1) , 460-471
Al7075-B4C KOMPOZİTLERİN TOZ METALÜRJİSİ VE SICAK PRESLEMEYLE ÜRETİMİ, MEKANİK ÖZELLİKLERİNİN İNCELENMESİ
Bu çalışmada, Al7075 alaşımı matrise ağırlıkça %1, 3, 6, 9, 12, 15 ve 30 oranlarında bor karbür ilavesi yapılarak Al7075-B4C kompozit malzemeler, toz metalürjisi ve sıcak presleme yöntemleri kullanılarak üretilmiştir. Bor karbür katkı oranının mikroyapı ile mekanik özellikler (yoğunluk, gözeneklilik oranı, Vickers sertliği ve basma dayanımı) üzerindeki etkisi incelenmiştir. Yürütülen testler sonucunda en yüksek yoğunluk (2,63 g/cm³), Vickers sertliği (256 HV), basma dayanımı (509 MPa) ve en düşük gözeneklilik oranı (%0,5) Al7075-30B4C kompozitte elde edilmiştir. Mikroyapı incelemelerinde, %30 B4C katkı oranıyla takviye partiküllerinin matris içinde homojen bir dağılım gösterdiği tespit edilmiştir. Sonuç olarak, %30 B4C katkısının Al7075 matrisli kompozitin mikroyapısını ve mekanik özelliklerini önemli ölçüde iyileştirdiği görülmüştür.
- 3 March 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (1) , 460-471
Open AccessAl7075-B4C KOMPOZİTLERİN TOZ METALÜRJİSİ VE SICAK PRESLEMEYLE ÜRETİMİ, MEKANİK ÖZELLİKLERİNİN İNCELENMESİ
Bu çalışmada, Al7075 alaşımı matrise ağırlıkça %1, 3, 6, 9, 12, 15 ve 30 oranlarında bor karbür ilavesi yapılarak Al7075-B4C kompozit malzemeler, toz metalürjisi ve sıcak presleme yöntemleri kullanılarak üretilmiştir. Bor karbür katkı oranının mikroyapı ile mekanik özellikler (yoğunluk, gözeneklilik oranı, Vickers sertliği ve basma dayanımı) üzerindeki etkisi incelenmiştir. Yürütülen testler sonucunda en yüksek yoğunluk (2,63 g/cm³), Vickers sertliği (256 HV), basma dayanımı (509 MPa) ve en düşük gözeneklilik oranı (%0,5) Al7075-30B4C kompozitte elde edilmiştir. Mikroyapı incelemelerinde, %30 B4C katkı oranıyla takviye partiküllerinin matris içinde homojen bir dağılım gösterdiği tespit edilmiştir. Sonuç olarak, %30 B4C katkısının Al7075 matrisli kompozitin mikroyapısını ve mekanik özelliklerini önemli ölçüde iyileştirdiği görülmüştür.
- Open Access
- 31 December 2024
- Published by Ordu University in Ordu Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (2) , 307-320
Al7075-Al2O3 Kompozitlerin Toz Metalürjisi ve Sıcak Preslemeyle Üretimi ve Mekanik Özelliklerinin Araştırılması
Bu çalışmada, ağırlıkça farklı oranlarda (%1, 3, 6, 9, 12, 15) alümina (Al2O3) içeren Al7075 alüminyum matrisli kompozitlerin üretimi ve karakterizasyonu gerçekleştirilmiştir. Toz metalürjisi ve indüksiyonla sıcak presleme yöntemleriyle üretilen numunelerin mikroyapısı, yoğunluğu, gözeneklilik oranı, sertliği ve basma dayanımı incelenmiştir. Çalışma sonucunda artan alümina takviyesinin belli bir orana kadar (ağırlıkça %12) kompozitin mekanik özelliklerini arttırdığı görülmüştür. En yüksek yoğunluğa (2.7 g cm-3), sertliğe (170±2 HV), basma dayanımına (471±6 MPa) ve en düşük gözeneklilik oranına (%8.2) Al7075-%12Al2O3 kompozitte erişilmiştir. Ancak ağırlıkça %15 alümina takviye oranında alümina partiküllerinin topaklanmasından kaynaklı olarak mekanik özeliklerde düşüş görülmüştür.
- 31 December 2024
- Published by Ordu University in Ordu Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (2) , 307-320
Open AccessAl7075-Al2O3 Kompozitlerin Toz Metalürjisi ve Sıcak Preslemeyle Üretimi ve Mekanik Özelliklerinin Araştırılması
Bu çalışmada, ağırlıkça farklı oranlarda (%1, 3, 6, 9, 12, 15) alümina (Al2O3) içeren Al7075 alüminyum matrisli kompozitlerin üretimi ve karakterizasyonu gerçekleştirilmiştir. Toz metalürjisi ve indüksiyonla sıcak presleme yöntemleriyle üretilen numunelerin mikroyapısı, yoğunluğu, gözeneklilik oranı, sertliği ve basma dayanımı incelenmiştir. Çalışma sonucunda artan alümina takviyesinin belli bir orana kadar (ağırlıkça %12) kompozitin mekanik özelliklerini arttırdığı görülmüştür. En yüksek yoğunluğa (2.7 g cm-3), sertliğe (170±2 HV), basma dayanımına (471±6 MPa) ve en düşük gözeneklilik oranına (%8.2) Al7075-%12Al2O3 kompozitte erişilmiştir. Ancak ağırlıkça %15 alümina takviye oranında alümina partiküllerinin topaklanmasından kaynaklı olarak mekanik özeliklerde düşüş görülmüştür.
- 15 September 2024
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 7 (5) , 939-945
Compressive Strength Analysis of Additively Manufactured Zirconia Honeycomb Sandwich Ceramic Parts with Different Cellular Structures
In this study, ZrO2 honeycomb sandwich structures with different cellular geometry were manufactured by SLA 3D-printing technology to analyze the compressive strength behaviour. After the printing procedure, the samples were sintered at 1450 °C for 2h. Among the samples with different cellular geometry, ZrO2 parts with circular cells were superior to that of square and triangular honeycomb structures and 1867±320 MPa compressive strength was obtained for this structure. The stress distributions in honeycomb structures were investigated using the COMSOL Multiphysics® for exposing the effect of cellular geometry on compressive strength. While more uniform stress distributions were seen on the inner wall of the circular honeycomb sample, the cellular structure of the square and triangle honeycomb samples mostly displayed compressive stress concentration on the joints of the honeycomb structure. Also, according to Rankine failure criterion, the parts with square cellular geometries were found to be more prone to failure. The highest specific compressive strength was obtained for the ZrO2 parts with circular cellular geometry. These findings demonstrated that the ZrO2 honeycomb sandwich structures with circular cellular geometry produced using SLA ceramic 3D-printing technology may be a suitable material to utilize in lightweight structural designs.
- 15 September 2024
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 7 (5) , 939-945
Compressive Strength Analysis of Additively Manufactured Zirconia Honeycomb Sandwich Ceramic Parts with Different Cellular Structures
In this study, ZrO2 honeycomb sandwich structures with different cellular geometry were manufactured by SLA 3D-printing technology to analyze the compressive strength behaviour. After the printing procedure, the samples were sintered at 1450 °C for 2h. Among the samples with different cellular geometry, ZrO2 parts with circular cells were superior to that of square and triangular honeycomb structures and 1867±320 MPa compressive strength was obtained for this structure. The stress distributions in honeycomb structures were investigated using the COMSOL Multiphysics® for exposing the effect of cellular geometry on compressive strength. While more uniform stress distributions were seen on the inner wall of the circular honeycomb sample, the cellular structure of the square and triangle honeycomb samples mostly displayed compressive stress concentration on the joints of the honeycomb structure. Also, according to Rankine failure criterion, the parts with square cellular geometries were found to be more prone to failure. The highest specific compressive strength was obtained for the ZrO2 parts with circular cellular geometry. These findings demonstrated that the ZrO2 honeycomb sandwich structures with circular cellular geometry produced using SLA ceramic 3D-printing technology may be a suitable material to utilize in lightweight structural designs.
- Open Access
- 18 May 2024
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 37 (4) , 1
Investigation of Microstructures and Mechanical Properties of Al2024/6061/7075-Graphene Composites
This work aimed to compare the mechanical properties and microstructures of Al2024-graphene, Al6061-graphene, and Al7075-graphene composites produced via the induction hot pressing and powder metallurgy method. The influences of graphene content (0.15-0.45wt.%), heat treatment (sintering and induction hot-pressing), and matrix material (Al2024, Al6061, and Al7075) on the mechanical strength and microstructure of specimens were studied. Compared to Al2024, Al6061 and Al7075 alloys, the compressive strength of Al2024-0.15graphene, Al6061-0.15graphene and Al7075-0.15graphene composites increased by 33.74%, 24.9% and 32%, respectively. The highest compressive strength (506±5 MPa), hardness (164±1.5 HV), and apparent density (2.65 g/cm3) were achieved in sintered and induction heat-treated Al7075-0.15%graphene composite. As a result, it was determined that graphene is an effective reinforcement element. It has been determined that induction hot-pressing improves the mechanical strength of composite materials.
- 18 May 2024
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 37 (4) , 1
Open AccessInvestigation of Microstructures and Mechanical Properties of Al2024/6061/7075-Graphene Composites
This work aimed to compare the mechanical properties and microstructures of Al2024-graphene, Al6061-graphene, and Al7075-graphene composites produced via the induction hot pressing and powder metallurgy method. The influences of graphene content (0.15-0.45wt.%), heat treatment (sintering and induction hot-pressing), and matrix material (Al2024, Al6061, and Al7075) on the mechanical strength and microstructure of specimens were studied. Compared to Al2024, Al6061 and Al7075 alloys, the compressive strength of Al2024-0.15graphene, Al6061-0.15graphene and Al7075-0.15graphene composites increased by 33.74%, 24.9% and 32%, respectively. The highest compressive strength (506±5 MPa), hardness (164±1.5 HV), and apparent density (2.65 g/cm3) were achieved in sintered and induction heat-treated Al7075-0.15%graphene composite. As a result, it was determined that graphene is an effective reinforcement element. It has been determined that induction hot-pressing improves the mechanical strength of composite materials.
- Open Access
- 15 December 2023
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 13 (4) , 1581-1594
Exploring Microstructure and Bending Strength of Al2O3 Ceramics Doped with Sm2O3 Rare-Earth Oxide: Impact of Volume Ratios and Sintering Temperatures
The effects of low amounts (0, 0.1, 0.3, 0.5, 0.8, 1, 2vol%) of Sm2O3 on the densification, microstructure, and bending strength of Al2O3 were studied for different sintering temperatures. Sm2O3 and Al2O3 powders were mixed by ball milling, and Al2O3-Sm2O3 ceramics were prepared by dry and cold isostatic pressing in disc form before pressureless sintering at 1550°C and 1600°C/2 h in the air, separately. Sm2O3 reacted with Al2O3 by forming SmAlO3. The rod-like morphology of the SmAlO3 was generally achieved for 0.8 and 1vol% Sm2O3 for sintering at 1600°C, whereas the rod-like form was more obvious for the samples sintered at 1550°C. Similar relative densities were attained for all Sm2O3 ratios at both sintering temperatures, but the Al2O3 sintered at 1550°C exhibited higher densification than the Al2O3 sintered at 1600°C. The strength values were close, while a strength increase of about 5% was obtained for 0.5 vol% Sm2O3 containing ceramics sintered at 1600°C caused by the higher densification compared to the Al2O3. The strength showed a prominent drop above the ratio of 0.1 vol% Sm2O3 for sintering at 1550°C. The addition of present amounts of Sm2O3 did not have a significant effect on the mechanical properties of Al2O3 but it changed the microstructure.
- 15 December 2023
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 13 (4) , 1581-1594
Open AccessExploring Microstructure and Bending Strength of Al2O3 Ceramics Doped with Sm2O3 Rare-Earth Oxide: Impact of Volume Ratios and Sintering Temperatures
The effects of low amounts (0, 0.1, 0.3, 0.5, 0.8, 1, 2vol%) of Sm2O3 on the densification, microstructure, and bending strength of Al2O3 were studied for different sintering temperatures. Sm2O3 and Al2O3 powders were mixed by ball milling, and Al2O3-Sm2O3 ceramics were prepared by dry and cold isostatic pressing in disc form before pressureless sintering at 1550°C and 1600°C/2 h in the air, separately. Sm2O3 reacted with Al2O3 by forming SmAlO3. The rod-like morphology of the SmAlO3 was generally achieved for 0.8 and 1vol% Sm2O3 for sintering at 1600°C, whereas the rod-like form was more obvious for the samples sintered at 1550°C. Similar relative densities were attained for all Sm2O3 ratios at both sintering temperatures, but the Al2O3 sintered at 1550°C exhibited higher densification than the Al2O3 sintered at 1600°C. The strength values were close, while a strength increase of about 5% was obtained for 0.5 vol% Sm2O3 containing ceramics sintered at 1600°C caused by the higher densification compared to the Al2O3. The strength showed a prominent drop above the ratio of 0.1 vol% Sm2O3 for sintering at 1550°C. The addition of present amounts of Sm2O3 did not have a significant effect on the mechanical properties of Al2O3 but it changed the microstructure.