GZGuchang Zhang

Guchang Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guchang Zhang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental investigation of competitive multi-fracture propagation and temporary plugging diversion under different perforation schemes: insights from real-time fiber-optic monitoring

    by Guchang Zhang, Tiankui Guo, Ming Chen, Zunpeng Hu, Yangui Hu, Zhihuang Lin, Tianyu Niu

    Multi-cluster fracturing often yields non-uniform fracture propagation due to stress shadowing and dynamic fluid partitioning. Near-wellbore temporary plugging and diversion can mitigate this problem, yet their interacting effects remain poorly understood. To address this gap, five perforation schemes—fixed-plane (8 and 12 holes), non-uniform, spiral, and directional single-hole—were created by abrasive water-jet perforation and tested under true triaxial conditions with real-time fiber-optic strain and acoustic emission monitoring. Results demonstrate that stress shadowing universally drives skip‐cluster initiation , causing non‐uniform and asynchronous initiation and asymmetric fracture‐wing widths. During temporary plugging, stable bridging locally enhances perforation friction, enabling diversion by overcoming stress shadowing. The concentrated 12‐hole scheme offered multiple bridging sites and yielded two diversion stages, whereas the dispersed spiral scheme could not bridge, producing a spurious 160.3% pressure surge without new fractures. Non‐uniform perforation locally increased toe‐side friction, promoted bi‐wing fracture formation, and improved post‐plugging symmetry, though the pressure rise was modest (29.1%). The directional single‐hole scheme intensified local friction and required the highest breakdown pressure (13.08 MPa), but the absence of complementary initiation sites allowed stress shadowing to dominate, yielding exclusively single‐wing fractures and poor plugging reliability. Parallel fracture swarms in fixed‐plane and non‐uniform cases match HFTS core evidence, confirming the field relevance of our experimental approach. These findings provide a mechanistic basis for optimizing perforation configuration and temporary plugging treatments in multi-cluster fracturing.

  • Promoting the uniform propagation of multi-fracture through adjusting the injection rate and perforation parameter: A numerical study

    by Bo Wang, Guchang Zhang, Li Zhang, Jinjun Liu, Fujian Zhou

    The strong stress interference and fluid competitive distribution result in the non-uniform propagation of multiple fractures during horizontal well multi-stage hydraulic fracturing (HWMHF). The uniform stimulation effect can be effectively improved by adjusting the injection rate and perforation scheme. In this work, a two-dimensional fluid–solid fully coupled multi-fracture propagation model is established to investigate the pattern of multi-fracture propagation and the flow distribution. The considering factors include the fluid injection rate, the perforation parameters, and the reservoir heterogeneity. The pipe element is developed to realize the free fluid distribution among multiple fractures. The results show that multiple fractures are more likely to initiate simultaneously and propagate uniformly with a higher fluid injection rate. The stress interference among multiple fractures can be balanced and the equilibrium propagation degree of multiple fractures can be greatly improved by reducing the perforation number. In the homogeneous reservoir, when the fluid injection rate is 12 m3/min and the perforation number per cluster is reduced to 10, the difference coefficient of fluid distribution can be reduced to 3.31%. In the heterogeneous reservoir, multiple perforation clusters with different tensile strengths can generate nearly uniform fractures by increasing the fluid injection rate and reducing the perforation number. When the fluid injection rate is 12 m3/min and the perforation number per cluster is 6, the difference coefficient of fluid distribution can be reduced to 3.26%. This work is of great significance in clarifying the propagation pattern and optimizing the fluid injection rate and the perforation number to improve the uniform propagation degree of multiple fractures.


  • Open Access

    Plugging characteristics of self-degradable diverters within three-dimensional hydro-fractures: An experimental investigation

    by Bo Wang, Guchang Zhang, Zhenglong Sun, Jinjun Liu, Yonggui Ma, Fujian Zhou

    The dominant fracture can be effectively plugged by injecting self-degradable diverters during temporary plugging fracturing. The subsequent fracturing fluids can divert into the poor fractures. The fracture complexity can be enlarged and the well production can be enhanced. This study established a new diverter temporary plugging evaluation system and carried out 23 groups of temporary plugging experiments to investigate the plugging characteristics of diverters within three-dimensional (3D) hydro-fractures. Experimental results show that (1) the formation process of a temporary plugged zone is determined by the bridging capability of the most significant particulates; (2) the tight plugged zone can undergo diverter attachment, bridging, filling, and compaction or diverter bridging, filling, and compaction; (3) diverters are most likely to plug distorted fractures, followed by inclined-flat fractures, and then axial/transverse-flat fractures due to the varying widths of hydro-fractures; (4) pure fibers can plug hydro-fractures when the fracture width is less than 1.5 mm, and the difference in the diameter of bridging particulates and the fracture width should be less than 1.5 mm when the fracture width exceeds 2.5 mm. Meanwhile, this study investigates the optimal temporary plugging agent formulations for different fracture widths based on economic factors and operational conditions, providing on-site recommendations.