Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Juan L. Bellido has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fixed-Frequency Dual-Active-Bridge Resonant Converter with Four Degrees of Freedom Using Triple Phase Shift and Current-Controlled Variable-Inductor

    by Juan L. Bellido, Vicente Esteve, Mattia Vogni, José Jordán

    The increasing adoption of electric vehicles (EVs) demands highly efficient bidirectional DC–DC converters capable of seamless energy transfer between the grid and vehicle batteries. This paper introduces a Fixed-Frequency Dual-Active-Bridge (DAB) resonant converter featuring four degrees of freedom, achieved through a combination of triple phase-shift (TPS) modulation and a current-controlled variable inductor (VI). The proposed control strategy aims to minimize conduction and switching losses by simultaneously managing reactive power, RMS current, and soft-switching conditions across wide variations in voltage and power. Unlike conventional phase-shift or variable-frequency modulations, the fixed-frequency operation maintains full zero-voltage switching (ZVS) for the two bridges, and zero-current switching (ZCS) in the bridge that is receiving energy, enhancing overall system reliability and control simplicity. The proposed converter is validated through simulations and experimental results from a SiC MOSFET-based 14 kW prototype operating at 122 kHz, demonstrating peak efficiencies above 97% under both charging and discharging modes. The experimental results confirm that the proposed DAB topology and modulation scheme significantly improve efficiency and controllability, making it a promising solution for next-generation on-board chargers and vehicle-to-grid (V2G) applications.

  • Open Access

    Application and Development of a Double Asymmetric Voltage Modulation on a Resonant Dual Active Bridge

    by Mattia Vogni, Juan L. Bellido, Fausto Stella, Leonardo Stefanini, Claudio Bianchini, Vicente Esteve

    The growing market penetration of Electric Vehicles (EVs) requires very efficient bidirectional on-board chargers. These converters must allow the power transfer from the grid to the battery of the vehicle and vice versa, since Vehicle to Grid (V2G) applications enable a mitigation of the peak demand and help regulate both the voltage and the frequency of the grid. In this paper, an innovative double asymmetric modulation was studied and applied to a resonant Dual Active Bridge (DAB), CLLC resonant filter configuration. The results of the study showed a significant efficiency boost and an easier controllability of the converter with respect to more traditional modulations or variable frequency techniques, maintaining Zero-Voltage Switching (ZVS) conditions for all the switches in a wide operating range, from 28 to 100% of the maximum power (4–14 kW). A map of optimum points, where converter losses are minimized, is calculated offline through an algorithm in MATLAB R2024a and a proper interpolation between these points allows any output power for each possible voltage level of the battery to be achieved: from 250 V up to 400 V. The modulations are compared and evaluated through simulations carried out in PLECS, both offline and using hardware-in-the-loop (HIL), as well as through experimental tests.


  • Open Access

    Optimizing the Efficiency of Series Resonant Half-Bridge Inverters for Induction Heating Applications

    by Vicente Esteve, José Jordán, Juan L. Bellido

    This paper reviews the current state of research on half-bridge (HB) inverters used in induction heating power supplies, emphasizing their topological structures, output power control methods, and switching strategies. The study explores various control techniques to regulate low power levels in a series resonant inverter (SRI) configured with an HB structure for induction heating applications. Pulse frequency modulation (PFM) is commonly employed to regulate standard power levels by adjusting the operating frequency relative to the resonant frequency. As the operating frequency increases beyond resonance, the output power decreases. However, in certain scenarios, achieving low power levels necessitates high frequencies, which introduces significant control challenges. To address these issues, it is crucial to develop alternative approaches that ensure efficient power reduction, without compromising system performance. This work evaluates and compares multiple solutions tailored for a high-frequency induction heating system delivering 18 kW at an operating frequency of approximately 100 kHz. The study places particular emphasis on optimizing key component sizing and analyzing inverter losses to enhance overall system efficiency and reliability.


  • Open Access

    Efficiency Design of a Single-Phase Bidirectional Rectifier for Home Energy Management Systems

    by Vicente Esteve, Juan L. Bellido, José Jordán

    This paper examines the current state of Home Energy Management Systems (HEMSs), highlighting the key role of the single-phase bidirectional rectifier (SPBR). It provides a detailed design process for the converter used in HEMSs, with a particular focus on the bidirectional charge and discharge of high-voltage batteries. The converter’s operating conditions were determined through a comprehensive evaluation of its components, which were designed and assessed to enable accurate power loss calculations. This approach ensures proper component sizing and a clear understanding of the converter’s efficiency. A specialized electronic control circuit manages two operating modes of the converter: a boost rectifier with power factor correction (PFC) and a sinusoidal pulse width modulation (SPWM) inverter. To validate the design, a 7.4 kW prototype was developed using silicon carbide (SiC) metal oxide semiconductor field effect transistors (MOSFETs). The prototype achieved a peak efficiency of nearly 98% in both modes, with a unity power factor (PF) and total harmonic distortion (THD) below 7% at full power.


  • Open Access

    Reactive Elements Control in LC Series Resonant Inverters by Current-Controlled Variable-Transformer and Magnetic Energy Recovery Switch for Induction Heating

    by Juan L. Bellido, Vicente Esteve, José Jordán

    This work consists of the analysis and design of a LC series resonant inverter with reactive element control for induction heating hardening applications. This novel method uses a current-controlled variable transformer (VT) to control the reflected inductance of the inductor in the resonant, and a magnetic energy recovery switch (MERS) to vary the influence of the capacitor as a reactive power compensation element. This converter topology allows quality factor (Q) or operating frequency (fsw) to be adjusted, making it possible to harden workpieces of different geometries and materials with a single converter. In the article, the design of both elements will be studied and tested. Experimental results were carried out with a 10 kW induction heating inverter prototype, with a frequency range of 60 kHz to 100 kHz and a quality factor of 6 to 10, measuring efficiencies above 95%.


  • Open Access

    Performance Enhancement in LC Series Resonant Inverters with Current-Controlled Variable-Transformer and Phase Shift for Induction Heating

    by Juan L. Bellido, Vicente Esteve, José Jordán

    This article presents an analysis of a converter based on an LC resonant inverter for induction heating applications. It employs a current-controlled variable transformer (VT) in conjunction with phase shift regulation (PS) to operate at a fixed frequency close to the resonance frequency. The converter maintains a small switching angle, enabling substantial load variations without sacrificing zero voltage switching (ZVS) for the transistors. This innovative method enhances the inverter’s performance across the entire operating range. Additionally, a new design of the transformer structure with a variable ratio will be analyzed, enabling mathematical modeling. The obtained results demonstrate a performance exceeding 99%. Both the inverter and variable transformer designs were experimentally validated using a 15 kW, 200 kHz converter for induction heating applications with silicon carbide (SiC) MOSFETs.


  • Open Access

    Efficiency Optimization in Parallel LLC Resonant Inverters with Current-Controlled Variable-Inductor and Phase Shift for Induction Heating

    by Juan L. Bellido, Vicente Esteve, José Jordán

    This paper presents a comprehensive analysis of a novel control approach to improve the efficiency of parallel LLC resonant inverters using a combination of a current controlled variable inductor (VI) and phase shift (PS). The proposed control aims to reduce the Root Mean Square (RMS) current, thereby reducing conduction and switching losses, and improving power transfer efficiency, while considering zero-voltage-switching (ZVS) operation, output power variations and load changes. Furthermore, a design methodology for the variable inductor is proposed, and design considerations relevant to this application are discussed. The effectiveness of the proposed approach is evaluated through mathematical modeling and experimental results. The mathematical modeling results show that the proposed approach, utilizing SiC MOSFETs, maintains a maximum efficiency of 98.5% for a 20 kW inverter over a wider range of output power, which is a significant improvement over existing approaches. The experimental results also confirm the effectiveness of the proposed control in improving the efficiency of parallel LLC resonant inverters.


  • Open Access

    State of the Art and Future Trends in Monitoring for Industrial Induction Heating Applications

    by Vicente Esteve, Juan L. Bellido, José Jordán

    Induction surface hardening (ISH) processes are widely used in the heat treatment of numerous industrial components, especially in the automotive industry. Since this industry operates under very demanding quality standards, it is crucial for these heat treatment processes to meet rigorous specifications to ensure the safety and reliability of the produced components. This implies the precise and repeatable control of certain parameters throughout the manufacturing process of each of the parts treated, through precise and reliable instrumentation in electromagnetically harsh environments. The main objective of this work is to define the monitoring process for an industrial IHS application, determining the control needs and the methods of measurement, recording, and verification of the parameters that ensure the quality of the process. This paper describes the monitoring process of induction surface hardening, emphasizing the use of sensors and modern measurement and control systems. A comprehensive monitoring system supported by a programmable logic controller (PLC) and mixed acquisition and instrumentation systems (analog and digital) implemented with a high-performance Field Programmable Gate Array (FPGA) will be presented.


  • Open Access

    Optimal Design of a Single-Phase Bidirectional Rectifier

    by Vicente Esteve, Juan L. Bellido, José Jordán

    This article outlines the comprehensive design and control approach for a single-phase bidirectional rectifier (SPBR) used in bidirectional charging of electric vehicle batteries. The operational parameters of the inverter are determined through a thorough analysis of all switching sequences to accurately assess power losses, considering the type of switching device chosen in each case, enabling proper component sizing, and understanding converter efficiency. An exclusive electronic control circuit is examined, governing two converter operation modes: boost rectifier with power factor correction (PFC) and sine pulse inverter width modulation (SPWM) with a minimum number of adjustments made automatically. One problem that arises when addressing the design of an SPBR is determining the operating frequency. To address this issue, this study offers to conduct a comparative analysis of losses using various power devices and magnetic circuits to determine the optimal operating frequency for achieving maximum energy efficiency. To validate the design’s feasibility, a prototype with 10 kW output power was constructed, achieving a peak efficiency of approximately 97.5% in both directions, unity power factor (PF), and total harmonic distortion (THD) of less than 7% during full power operation.


  • Open Access

    Improving the Efficiency of an Isolated Bidirectional Dual Active Bridge DC–DC Converter Using Variable Frequency

    by Vicente Esteve, Juan L. Bellido, José Jordán, Enrique J. Dede

    This article presents a control method for an isolated bidirectional dual active bridge DC–DC converter (IBDC) where single phase shift (SPS) and variable frequency (VF) modulations are combined simultaneously with the purpose of improving the efficiency of the converter applied to the bidirectional charging of electric vehicles batteries. A complete power characterization of the dual active bridge (DAB) converter is carried out. The combined control achieves lossless turn-on and turn-off on the primary bridge for a wide range of output powers. A comparative study of power losses between the traditional SPS control and the combined method proposed here was also carried out. A prototype with an output power of 10 kW was built based on Silicon Carbide (SiC) Metal Oxide Semiconductor Field-Effect Transistors (MOSFET), with which a peak efficiency close to 99% was obtained, thus verifying the viability of the method.