MVMattia Vogni

Mattia Vogni

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mattia Vogni has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fixed-Frequency Dual-Active-Bridge Resonant Converter with Four Degrees of Freedom Using Triple Phase Shift and Current-Controlled Variable-Inductor

    by Juan L. Bellido, Vicente Esteve, Mattia Vogni, José Jordán

    The increasing adoption of electric vehicles (EVs) demands highly efficient bidirectional DC–DC converters capable of seamless energy transfer between the grid and vehicle batteries. This paper introduces a Fixed-Frequency Dual-Active-Bridge (DAB) resonant converter featuring four degrees of freedom, achieved through a combination of triple phase-shift (TPS) modulation and a current-controlled variable inductor (VI). The proposed control strategy aims to minimize conduction and switching losses by simultaneously managing reactive power, RMS current, and soft-switching conditions across wide variations in voltage and power. Unlike conventional phase-shift or variable-frequency modulations, the fixed-frequency operation maintains full zero-voltage switching (ZVS) for the two bridges, and zero-current switching (ZCS) in the bridge that is receiving energy, enhancing overall system reliability and control simplicity. The proposed converter is validated through simulations and experimental results from a SiC MOSFET-based 14 kW prototype operating at 122 kHz, demonstrating peak efficiencies above 97% under both charging and discharging modes. The experimental results confirm that the proposed DAB topology and modulation scheme significantly improve efficiency and controllability, making it a promising solution for next-generation on-board chargers and vehicle-to-grid (V2G) applications.

  • Comprehensive Load Loss Model of an Ironless Machine: Advantages of Current Source Inverter Supply

    by Mattia Vogni, Giada Sala, Elena Macrelli, Claudio Bianchini, Alberto Bellini

    Accurate loss modeling in electric machines is a critical enabler for design optimization. By providing more faithful estimates of thermal stress, loss models may also contribute to extended insulation and permanent-magnet lifetimes. Loss modeling has been widely investigated, and existing approaches can be broadly grouped into three classes: (i) analytical models; (ii) numerical finite-element (FEA) methods; and (iii) hybrid schemes that combine analytical formulations with numerical field solutions. Ironless (coreless) machines constitute a special case for AC loss prediction. In such topologies, iron-core losses are essentially absent, so winding AC losses tend to dominate, and magnet losses may become non-negligible under high-frequency excitation. AC losses of these machines, which are suitable for FESS applications, have been under-investigated in literature. This paper presents a comprehensive loss model for ironless machines that jointly treats winding and magnet losses and distinguishes between fundamental and carrier-frequency components for both coils and magnets. The framework is experimentally assessed on a prototype for a flywheel energy storage system (FESS) application. A current source inverter (CSI) supply appears to reduce AC losses and current ripple relative to a conventional voltage source inverter (VSI), suggesting potential efficiency and thermal advantages for ironless drives under comparable conditions.

  • Open Access

    Application and Development of a Double Asymmetric Voltage Modulation on a Resonant Dual Active Bridge

    by Mattia Vogni, Juan L. Bellido, Fausto Stella, Leonardo Stefanini, Claudio Bianchini, Vicente Esteve

    The growing market penetration of Electric Vehicles (EVs) requires very efficient bidirectional on-board chargers. These converters must allow the power transfer from the grid to the battery of the vehicle and vice versa, since Vehicle to Grid (V2G) applications enable a mitigation of the peak demand and help regulate both the voltage and the frequency of the grid. In this paper, an innovative double asymmetric modulation was studied and applied to a resonant Dual Active Bridge (DAB), CLLC resonant filter configuration. The results of the study showed a significant efficiency boost and an easier controllability of the converter with respect to more traditional modulations or variable frequency techniques, maintaining Zero-Voltage Switching (ZVS) conditions for all the switches in a wide operating range, from 28 to 100% of the maximum power (4–14 kW). A map of optimum points, where converter losses are minimized, is calculated offline through an algorithm in MATLAB R2024a and a proper interpolation between these points allows any output power for each possible voltage level of the battery to be achieved: from 250 V up to 400 V. The modulations are compared and evaluated through simulations carried out in PLECS, both offline and using hardware-in-the-loop (HIL), as well as through experimental tests.


  • Open Access

    Analytical Model and Feasibility Assessment of a Synchronous Reluctance Tubular Machine with an Additively Manufactured Mover

    by Giada Sala, Nicola Giannotta, Mattia Vogni, Claudio Bianchini, Fabio Immovilli

    This paper presents the analytical model, feasibility assessment, and testing of a novel synchronous reluctance tubular machine, whose mover is manufactured using additive techniques. This approach enables the maximization of the machine’s saliency. The analytical model traditionally used for rotating machines was adapted to match the geometric characteristics of the innovative tubular design proposed in this work. The analytical results were validated through 2D finite element analysis (FEA). Subsequently, several mock-ups were 3D-printed using iron metal powder to evaluate the manufacturing feasibility of the proposed machine. Finally, the machine was tested to verify the accuracy of the analytical model.


  • Open Access

    Switching Loss Model for SiC MOSFETs Based on Datasheet Parameters Enabling Virtual Junction Temperature Estimation

    by Claudio Bianchini, Mattia Vogni, Alessandro Chini, Giovanni Franceschini

    SiC MOSFETs are widely employed in power converters due to their superior efficiency and reliability at high temperatures. For this reason, it is crucial to implement accurate thermal models capable of indirectly estimating the junction temperature and its fluctuations: both are caused by power losses in the device. In this framework, the evaluation of switching losses remains the most challenging task. To enable real-time monitoring of the junction temperature, this work presents the development of a virtual sensor specifically designed for SiC MOSFETs. The sensor relies on a num-analytical model (NAM), which employs only datasheet parameters and leverages electrical quantities—namely, bus voltage and current—available from sensors integrated into power converter systems. The proposed NAM is implemented in MATLAB using an iterative algorithm that accounts for the main physical phenomena involved in switching transitions. The computed energy losses are then used to thermally model the SiC MOSFETs within the PLECS environment, where a digital twin of an all-SiC board is created. Finally, the accuracy of the model is validated by comparing simulation results with experimental efficiency data obtained from a real half-bridge converter, with explicit consideration of measurement uncertainty.


  • Extended MTPA-FW Control Technique for PM Electrical Machines with CSI

    by Claudio Bianchini, Giada Sala, Matteo Frigieri, Mattia Vogni, Nicola Giannotta, Elena Macrelli

    This paper presents a new extended constant power region control model for interior permanent magnet synchronous machine (IPMSM) powered by a current source inverter (CSI). The IPMSM constant power region is usually obtained with voltage source inverter (VSI) employing flux weakening (FW) and maximum torque per volt (MTPV) control strategy when the voltage at the motor terminal exceed the available DC BUS voltage. This is due to the fact that VSI essentially operates as a step down converter. Even if these control strategy are well know in literature their implementation is always critical, specially when the MTPV is needed. As CSI is intrinsically a step up converter, it is possible to delay FW operation, provided that the voltage applied to the motor does not exceed the voltage rating of the power devices and the limits for the insulation system. So, in order to obtain a wide constant power region, an extend MTPA-FW is here proposed avoiding the need of MTPV and taking the advantage of the step-up intrinsic capability of the CSI.


  • Open Access

    Slot Design Optimization for Copper Losses Reduction in Electric Machines for High Speed Applications

    by Claudio Bianchini, Mattia Vogni, Ambra Torreggiani, Stefano Nuzzo, Davide Barater, Giovanni Franceschini

    The need of a wide operating range and a high power density in electric machines for full- and hybrid electric vehicles in traction applications has led to an increase in the operating frequency of the machine. When the electric frequency increases, the additional losses in stator windings become an issue and they have to be taken into account in the design of the electric machine. This issue is more critical when hairpin windings are employed, due to the the skin and proximity effects which produce increased copper losses. In this paper, the relationships between different stator slot parameters (tooth width, slot opening, etc.) and stator winding copper losses have been analysed in order to identify an optimal design of a single stator slot.