Yushu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yushu Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Wentao Zhai
School of Materials Science and Engineering Sun Yat‐sen University Guangzhou Guangdong Province China
3 shared publications - Junjie Jiang
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
2 shared publications - Yaozong Li
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
2 shared publications - Fangwei Tian
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
1 shared publication - Haishuo Li
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
1 shared publication - Hanyi Huang
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
1 shared publication
Latest Publications
- Open Access
Foam Rubber-Based Three-Layer Flexible Composite for High-Efficiency Infrared Stealth and Joule Heating
With the rapid development of infrared detection methods and military surveillance technologies, flexible and wearable infrared stealth materials (ISM) have attracted increasing attention. Inspired by the layered structure of penguins’ fat–feather–oil, this study prepared a three-layer MXene/waterborne polyurethane (WPU)-foam rubber-phase change microcapsule (PCM)/WPU composite material (M-F-P) via the solution blending and doctor-blading method. The outermost layer of the M-F-P composite is an MXene/WPU conductive film, which features a low infrared emissivity and Joule heating performance to adapt to suddenly cold environments. The porous foam rubber in the middle layer provides excellent thermal insulation performance, which effectively inhibits heat conduction and enhances infrared stealth efficiency. Meanwhile, as a four-directional elastic material, it exhibits deformation recovery capability in both the warp and weft directions as well as the 45° direction. The bottom layer of the PCM/WPU film has a phase change enthalpy of 154.3 J/g and possesses efficient thermal management capability. It achieves dynamic thermal regulation through the cycle of heat absorption at high temperatures and heat release at low temperatures.
Open AccessFoam Rubber-Based Three-Layer Flexible Composite for High-Efficiency Infrared Stealth and Joule Heating
With the rapid development of infrared detection methods and military surveillance technologies, flexible and wearable infrared stealth materials (ISM) have attracted increasing attention. Inspired by the layered structure of penguins’ fat–feather–oil, this study prepared a three-layer MXene/waterborne polyurethane (WPU)-foam rubber-phase change microcapsule (PCM)/WPU composite material (M-F-P) via the solution blending and doctor-blading method. The outermost layer of the M-F-P composite is an MXene/WPU conductive film, which features a low infrared emissivity and Joule heating performance to adapt to suddenly cold environments. The porous foam rubber in the middle layer provides excellent thermal insulation performance, which effectively inhibits heat conduction and enhances infrared stealth efficiency. Meanwhile, as a four-directional elastic material, it exhibits deformation recovery capability in both the warp and weft directions as well as the 45° direction. The bottom layer of the PCM/WPU film has a phase change enthalpy of 154.3 J/g and possesses efficient thermal management capability. It achieves dynamic thermal regulation through the cycle of heat absorption at high temperatures and heat release at low temperatures.
- Open Access
Shortening the Saturation Time of PBAT Sheet Foaming via the Pre-Introducing of Microporous Structures
Poly (butylene adipate-co-terephthalate) (PBAT) foam sheets prepared by foaming supercritical fluids are characterized by high resilience, homogeneous cellular structure, and well-defined biodegradability. However, the inert chemical structure and the rigid hard segments restrict the diffusion of CO2 within the PBAT matrix, resulting in extremely long gas saturation times as long as 9 h at a thickness of 12 mm. In this study, microporous structures were pre-introduced into the PBAT matrix to provide a fast gas diffusion pathway during the saturation process. After 2 h of saturation, PBAT foam sheets with expansion ratio of 10 to 13.8 times were prepared. The interaction of CO2 with PBAT was systematically investigated, and the CO2 sorption process was evaluated kinetically and thermodynamically using the Fickian diffusion theory. The solubility and diffusion rate of CO2 in pretreated PBAT sheets with different microporous sizes and densities were investigated, and the effects of pretreatment strategies on the foaming behavior and cell structure of PBAT foam sheets were discussed. The introduction of a microporous structure not only reduces saturation time but also enhances solubility, enabling the successful preparation of soft foams with high expansion ratios and resilience. After undergoing foaming treatment, the PBAT pretreated sheets with a 10 μm microporous structure and a density of 0.45 g/cm3 demonstrated improved mechanical properties: their hardness decreased to 35 C while resilience increased to 58%, reflecting enhanced elastic recovery capabilities. The pretreatment method, which increases the diffusion rate of CO2 in PBAT sheets, offers a straightforward approach that provides valuable insights into achieving rapid and efficient foaming of thick PBAT sheets in industrial applications.
Open AccessShortening the Saturation Time of PBAT Sheet Foaming via the Pre-Introducing of Microporous Structures
Poly (butylene adipate-co-terephthalate) (PBAT) foam sheets prepared by foaming supercritical fluids are characterized by high resilience, homogeneous cellular structure, and well-defined biodegradability. However, the inert chemical structure and the rigid hard segments restrict the diffusion of CO2 within the PBAT matrix, resulting in extremely long gas saturation times as long as 9 h at a thickness of 12 mm. In this study, microporous structures were pre-introduced into the PBAT matrix to provide a fast gas diffusion pathway during the saturation process. After 2 h of saturation, PBAT foam sheets with expansion ratio of 10 to 13.8 times were prepared. The interaction of CO2 with PBAT was systematically investigated, and the CO2 sorption process was evaluated kinetically and thermodynamically using the Fickian diffusion theory. The solubility and diffusion rate of CO2 in pretreated PBAT sheets with different microporous sizes and densities were investigated, and the effects of pretreatment strategies on the foaming behavior and cell structure of PBAT foam sheets were discussed. The introduction of a microporous structure not only reduces saturation time but also enhances solubility, enabling the successful preparation of soft foams with high expansion ratios and resilience. After undergoing foaming treatment, the PBAT pretreated sheets with a 10 μm microporous structure and a density of 0.45 g/cm3 demonstrated improved mechanical properties: their hardness decreased to 35 C while resilience increased to 58%, reflecting enhanced elastic recovery capabilities. The pretreatment method, which increases the diffusion rate of CO2 in PBAT sheets, offers a straightforward approach that provides valuable insights into achieving rapid and efficient foaming of thick PBAT sheets in industrial applications.
- Open Access
A Review of the Preparation of Porous Fibers and Porous Parts by a Novel Micro-Extrusion Foaming Technique
This review introduces an innovative technology termed “Micro-Extrusion Foaming (MEF)”, which amalgamates the merits of physical foaming and 3D printing. It presents a groundbreaking approach to producing porous polymer fibers and parts. Conventional methods for creating porous materials often encounter obstacles such as the extensive use of organic solvents, intricate processing, and suboptimal production efficiency. The MEF technique surmounts these challenges by initially saturating a polymer filament with compressed CO2 or N2, followed by cell nucleation and growth during the molten extrusion process. This technology offers manifold advantages, encompassing an adjustable pore size and porosity, environmental friendliness, high processing efficiency, and compatibility with diverse polymer materials. The review meticulously elucidates the principles and fabrication process integral to MEF, encompassing the creation of porous fibers through the elongational behavior of foamed melts and the generation of porous parts through the stacking of foamed melts. Furthermore, the review explores the varied applications of this technology across diverse fields and imparts insights for future directions and challenges. These include augmenting material performance, refining fabrication processes, and broadening the scope of applications. MEF technology holds immense potential in the realm of porous material preparation, heralding noteworthy advancements and innovations in manufacturing and materials science.
Open AccessA Review of the Preparation of Porous Fibers and Porous Parts by a Novel Micro-Extrusion Foaming Technique
This review introduces an innovative technology termed “Micro-Extrusion Foaming (MEF)”, which amalgamates the merits of physical foaming and 3D printing. It presents a groundbreaking approach to producing porous polymer fibers and parts. Conventional methods for creating porous materials often encounter obstacles such as the extensive use of organic solvents, intricate processing, and suboptimal production efficiency. The MEF technique surmounts these challenges by initially saturating a polymer filament with compressed CO2 or N2, followed by cell nucleation and growth during the molten extrusion process. This technology offers manifold advantages, encompassing an adjustable pore size and porosity, environmental friendliness, high processing efficiency, and compatibility with diverse polymer materials. The review meticulously elucidates the principles and fabrication process integral to MEF, encompassing the creation of porous fibers through the elongational behavior of foamed melts and the generation of porous parts through the stacking of foamed melts. Furthermore, the review explores the varied applications of this technology across diverse fields and imparts insights for future directions and challenges. These include augmenting material performance, refining fabrication processes, and broadening the scope of applications. MEF technology holds immense potential in the realm of porous material preparation, heralding noteworthy advancements and innovations in manufacturing and materials science.