OROleg Rusch

Oleg Rusch

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleg Rusch has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optical Critical Dimension Metrology for the SiC Trench MOSFET Process

    by Boglárka Dikó, Oleg Rusch, Julien Körfer, Zsófia Kiss, Attila Sütő, Emeric Balogh

    Silicon carbide (SiC) MOSFETs are widely utilized in power device applications for their numerous advantages, and the device’s properties can be further optimized through the implementation of trench structures. The formation of the trench structure is a multi-step process, in which it is important to monitor the result of each step and ensure that the structure meets the desired requirements. OCD (optical critical dimension) metrology can provide a fast, non-destructive solution for this purpose. In this article, an OCD analysis of structures at two different process steps is presented and compared with the results from the electron microscopy images. OCD results show high sensitivity to the geometrical dimensions of the structure and produce a good correlation with the electron microscopy images. This metrology can provide a means to detect subtle structural differences without causing any damage to the sample.

  • Open Access

    Increasing 4H-SiC Trench Depth by Improving the Dry Etch Selectivity towards the Oxide Hard Mask

    by Oleg Rusch, Kevin Brueckner, Johann Tobias Erlbacher

    This work presents the results of process development for trench formation in SiC power devices to increase the trench depth by improving SiC/SiO2-selectivity of the dry etch process. Motivation behind this development is to further improve the electrical properties of conventional devices like SiC MOSFETs by implementing a trench geometry, allowing the cell pitch to be increased, leading to a reduced on-resistance of SiC TrenchMOS devices. Trench etching was performed on 4H-SiC substrates by utilizing an oxide hard mask, patterned by photolithography and dry etching. The SiC trench profile was analyzed by cross-section preparation via FIB and SEM imaging. The highest SiC/SiO2-selectivity achieved was 7.9, with SiF4 gas flow being the most decisive parameter for it. With that, the selectivity of the standard SiC trench etch process was increased by nearly five times. SiC trenches with depths of 5 µm could be demonstrated. However, then the structural fidelity was deteriorated, with micro-trenching and sidewall bowing being the largest limitations regarding applicable trench depth in SiC power devices.


  • Open Access

    Long Term Reliability and Deterioration Mechanisms of High-Temperature Metal Stacks on 4H-SiC

    by Kevin Brueckner, Oleg Rusch

    In order to make SiC devices more accessible for high-temperature applications, reliable ohmic contacts and metallization systems which can also withstand extended operation at high temperatures are needed. In this work, metal layer stacks containing Ag, Ti, TiN, Ni and NiAl, where NiAl refers to a mixture of 97,4 wt% Ni and 2,6 wt% Al, were deposited on Si and SiC samples and consecutively thermally aged at 400 °C for 100 h in air. Mesa structures were found to be challenging for keeping oxygen from diffusing through the metal stack to the substrate. On flat surfaces, diffusion barriers were successfully used to protect the ohmic contact on 4H-SiC samples from oxidizing. Diffusion barriers made of TiN were found to show pore formation after the thermal treatment. The reason for the pores is thought to be gas formation, which is believed to be the result of the TiN layers containing too much nitrogen. The exact chemical composition of TiN layers therefore seems to be of vital importance for high-temperature applications.

  • Open Access

    Lift-Off Process for Patterning of a Sputter-Deposited Thick Metal Stack for High Temperature Applications on 4H-SiC

    by Alesa Fuchs, Kevin Brueckner, Kevin Ehrensberger, Oleg Rusch

    With the rising need for power devices suitable for harsh environment conditions like high temperature applications, contact materials and packaging of the devices have become critical factors in device fabrication [1, 2]. Therefore, a contact metal stack containing silver and titanium nitride which can be used at elevated temperatures under oxygen atmosphere was investigated. For patterning of the approx. 2 µm thick sputter-deposited metal stack on the wafer front side, a lift-off process using a negative photoresist was established. Characterization of the photoresist sidewall shape was performed by cross-sectional views prepared with SEM and top view images taken on a microscope. It was found that for a successful lift-off, a distinct undercut is needed so no metal is deposited at the downside of the undercut, ensuring a metal-free surface for the solvent to reach the photoresist. To obtain this, most influencing factors are exposure dose and development time, which were optimized considering the undercut shape as well as pattern fidelity. Lift-off with acetone proved to be good for the fabricated 4H-SiC MOSFET devices.

  • Open Access

    Plasma Treatment after NiSi-Based Ohmic Contact Formation on 4H-SiC to Enhance Adhesion of Subsequent Backside Metallization

    by Tom Becker, Carsten Hellinger, Alesa Fuchs, Julien Koerfer, Oleg Rusch

    To achieve low on-resistance in any vertical 4H-SiC semiconductor power device, it is essential to create a suitable ohmic contact on the corresponding n-doped SiC substrate. In particular after wafer thinning, a common technology to reduce substrate resistivity, laser annealing for ohmic contact formation on the wafer backside is the only option due to temperature sensitive materials (such as Titanium or Aluminum) on the partially or fully processed wafer frontside. In this work, to solve adhesion issues of the backside metallization, plasma treatments, as easy to integrate process steps, were examined. By stripping obstructive carbon layers, formed after ohmic contact laser annealing, and without damaging the wafer frontside, an enhanced adhesion of following metallization layers was achieved. Both O2- and H2-plasma processes were investigated and demonstrated significant improvements to the adhesion of metallization stacks on the wafer backside compared to untreated surfaces and without drawbacks in the ohmic contact quality.


  • Open Access

    Improvement of Reflectance Spectroscopy for Oxide Layers on 4H-SiC

    by Julien Koerfer, Mathias Rommel, Alesa Fuchs, Oleg Rusch

    In this work, we investigate the use of reflectance spectroscopy as an accurate, fast, and non-destructive method for measuring the thickness of transparent layers, such as SiO2, with thicknesses below 200 nm for microelectronic applications. To this end, we fabricated different oxides and analyzed their reflectance spectra using reflectance spectroscopy. The results were compared to theoretical reflectance spectra to validate the method. We introduce key factors to ensure accurate measurement by modeling the reflectance spectra of thin oxide layers with thicknesses ≥ 15 nm on 4H-SiC using the transfer matrix method (TMM).


  • Open Access

    Highly Efficient Floating Field Rings for SiC Power Electronic Devices - A Systematic Experimental Study

    by Lirong Z. Broderick, Jonathan Moult, Oleg Rusch, Tong Tong, Tobias Erlbacher, Yunji L. Corcoran

    A systematic experimental study is conducted on floating field rings (FFR) incorporated into 4H-SiC junction barrier Schottky (JBS) diodes across four voltage ratings 650, 1200, 1700 and 3300V, in pursuit of highly efficient FFR designs. 30 designs of FFR in 3 categories are studied for each voltage rating, and the measured breakdown voltage (Vbr) of JBS divided by ring system width (W) is taken as the figure of merit (FOM) of each design. The influence of ring spacing, ring width and number of rings on Vbr is studied in detail. It is found that the initial ring spacing (S1) is critical in determining the highest Vbr achievable by a certain design, and its optimum value increases as voltage rating increases. TCAD simulation verifies the importance of S1. For designs with a small ring system width, subsequent ring spacing can also become important. Ring width does not have a definitive effect, and Vbr saturates beyond a certain ring number. The design with the highest Vbr may not render the highest FOM. Even style designs with appropriate ring spacings can be advantageous likely due to less susceptibility to variation of field oxide charge, and more tolerance to fabrication error, as well as ease of design.


  • Open Access

    A Modeling of 4H-SiC Super-Junction MOSFETs with Filtered High Energy Implantation

    by Minwho Lim, Constantin Csato, Julietta Förthner, Oleg Rusch, Kevin Ehrensberger, Barbara Kupfer, Susanne Beuer, Susanne Oertel, Dong Wook Byun, Seong Jun Kim, et al.

    In this paper, the modeling of SJ-MOSFETs beyond the voltage class of 3.3 kV simulated with verified deep aluminum box-like shaped profiles by using TCAD simulation is described. The simulation results are used to investigate the influence of ion implantation parameters on electrical characteristics. For the formation of pillar regions, high energy implantation is performed through energy filter with a multi epitaxial growth method using a patterned mask. While high thickness of epitaxial layer is indispensable for obtaining a high blocking capability, it is revealed that the optimization of doping concentration of p-pillar and drift layer parameters yields similar on-state-resistance by charge compensations of SJ-structure.

  • Low-Resistance Ohmic Contact Formation by Laser Annealing of N-Implanted 4H-SiC

    by Carsten Hellinger, Oleg Rusch, Mathias Rommel, Anton J. Bauer, Tobias Erlbacher

    In this work, pulsed-laser-based tempering was applied for post-implant annealing of n-type N-doped 4H-SiC in order to electrically activate the dopants and to rebuild the crystal structure. The annealing was performed by a frequency-tripled Nd:YVO4 laser with a pulse duration of 60 ns. To evaluate the effects of post-implant annealing, JBS diodes were electrically characterized. The results were compared with implanted, not post-annealed JBS diodes. The electrical measurements showed a significant on-state voltage drop of 40 mV at 6 A for post-implant laser annealed diodes compared to not post-implant annealed diodes.


  • Reducing On-Resistance for SiC Diodes by Thin Wafer and Laser Anneal Technology

    by Oleg Rusch, Carsten Hellinger, Jonathan Moult, Yunji L. Corcoran, Tobias Erlbacher

    This work presents the influence of Thin Wafer und Laser Anneal Technology on the electrical performance of 4HSiC devices. Substrate thinning and backside ohmic contact formation via laser annealing were successfully applied to in-house designed and manufactured 6 A 650 V SiC diodes at IISB, improving its forward characteristics. The given devices exhibit an on-state voltage drop (VF) reduction from 1.78 V to 1.62 V at 6 A rated current while maintaining blocking capabilities of more than 1.1 kV with leakage currents less than 1 μA at 650 V nominal voltage. On-resistance (RON) was lowered by approx. 30 % to 90 mΩ and 60 % to 12 mΩ in Schottky and conductivity modulation state, respectively. Wafer thinning also allows reducing the influence of non-homogeneous distributed substrate doping concentrations, leading to a more narrow distribution of the forward characteristics of the devices across the wafer.