Ihor Lapytskyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ihor Lapytskyi has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Kuzmych
Київський національний університет будівництва і архітектури
2 shared publications - Svitlana Bondar
Kyiv National University of Construction and Architecture
2 shared publications - Andriy Annenkov
Київський національний університет будівництва і архітектури
1 shared publication - Olena Tsykolenko
Київський національний університет будівництва і архітектури
1 shared publication - Roman Demianenko
Kyiv National University of Construction and Architecture
1 shared publication - Yuriy Gulyaev1 shared publication
Latest Publications
- Open Access
- 17 April 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 112,p. 222-228
Analysis of the influence of external factors on the deformation of high-rise buildings in the process of their construction and operation
During the construction and operation of high-rise buildings, their vertical axis changes its position in space. The greater the height of the structure, the greater the amplitude of oscillations. This causes problems of geodetic construction support and the need to monitor deformations during the operation of high-rise structures. In real conditions, part of the structures will be in the shade and their temperature will be lower than the structures that will be under the influence of solar radiation, the temperature of which will be much higher. Thus, the building will deform as a result of uneven thermal expansion, that is, it will bend. From DBN B.1.3-2:2010 "Geodesic works in construction". Also, during the geodetic provision of the construction and operation of high-rise buildings, changes in the temperature regime of building structures should be taken into account in connection with significant absolute values of changes in the geometric dimensions of the building as a result of thermal expansion, which significantly exceed the accuracy regulated by the regulatory document. The article examines and analyzes the influence of external forces on changes in the geometry of high-rise structures and focuses attention on solving the scientific problem of geodetic support for the construction and operation of modern high-rise structures under dynamic loads.
- 17 April 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 112,p. 222-228
Open AccessAnalysis of the influence of external factors on the deformation of high-rise buildings in the process of their construction and operation
During the construction and operation of high-rise buildings, their vertical axis changes its position in space. The greater the height of the structure, the greater the amplitude of oscillations. This causes problems of geodetic construction support and the need to monitor deformations during the operation of high-rise structures. In real conditions, part of the structures will be in the shade and their temperature will be lower than the structures that will be under the influence of solar radiation, the temperature of which will be much higher. Thus, the building will deform as a result of uneven thermal expansion, that is, it will bend. From DBN B.1.3-2:2010 "Geodesic works in construction". Also, during the geodetic provision of the construction and operation of high-rise buildings, changes in the temperature regime of building structures should be taken into account in connection with significant absolute values of changes in the geometric dimensions of the building as a result of thermal expansion, which significantly exceed the accuracy regulated by the regulatory document. The article examines and analyzes the influence of external forces on changes in the geometry of high-rise structures and focuses attention on solving the scientific problem of geodetic support for the construction and operation of modern high-rise structures under dynamic loads.
- Open Access
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 321-328
SEARCH OF OPTIMAL SPATIAL PARAMETERS FOR GEODETIC DELINEATION OF MOTORWAY INTERCHANGES WITH BRAKING TRANSITION CURVES
The most widespread grade-separated road junction — cloverleaf interchange — is a complex engineering structure, in which all the parameters and limitations of the plan and longitudinal profile must be coordinated with each other. The goals of the analysis: traffic safety, technical and economic indicators of the movement of transport units, the compactness of left-turn and right-turn exits and, as an additional, but extremely important aspect, the minimization of the area occupied by the entire transport structure, which is very important in tight urban conditions. First, let's emphasize that the trajectories of cars at the intersection must correspond to their real variable speeds on left-turn exits, since this is traffic on curves of small radii. In our previous studies, it has been experimentally proven that cars entering a left-turning exit reduce their speed, and conversely, when leaving the exit, their speed increases. Therefore, it is necessary to use braking curves as transition curves of left-turn exits, and not clothoid curves, which are often used, and which are designed for constant speed of movement. Some braking transition curves designed for variable speed are also used in traffic junctions [4]. But, analyzing these curves, we came to the conclusion that they do not meet the classical purpose of the transition curve, namely, they do not provide the necessary radius at the end of the curve, which is equal to the radius of the circular insert for a smooth transition from a transition curve to a circular curve. This leads to dangerous moments of the car's movement at the junction of the transition and circular curves. Therefore, we previously derived the formulas of refined braking transition curves that meet the requirements of the radii of classical transition curves [1, 2]. In addition, it later turned out that these refined transition curves have, as an additional effect, the property of reducing the area occupied by the left-turn exit, as shown in Fig. 1. We offer a method for optimizing the spatial parameters of cloverleaf interchanges with refined braking transition curves.
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 321-328
Open AccessSEARCH OF OPTIMAL SPATIAL PARAMETERS FOR GEODETIC DELINEATION OF MOTORWAY INTERCHANGES WITH BRAKING TRANSITION CURVES
The most widespread grade-separated road junction — cloverleaf interchange — is a complex engineering structure, in which all the parameters and limitations of the plan and longitudinal profile must be coordinated with each other. The goals of the analysis: traffic safety, technical and economic indicators of the movement of transport units, the compactness of left-turn and right-turn exits and, as an additional, but extremely important aspect, the minimization of the area occupied by the entire transport structure, which is very important in tight urban conditions. First, let's emphasize that the trajectories of cars at the intersection must correspond to their real variable speeds on left-turn exits, since this is traffic on curves of small radii. In our previous studies, it has been experimentally proven that cars entering a left-turning exit reduce their speed, and conversely, when leaving the exit, their speed increases. Therefore, it is necessary to use braking curves as transition curves of left-turn exits, and not clothoid curves, which are often used, and which are designed for constant speed of movement. Some braking transition curves designed for variable speed are also used in traffic junctions [4]. But, analyzing these curves, we came to the conclusion that they do not meet the classical purpose of the transition curve, namely, they do not provide the necessary radius at the end of the curve, which is equal to the radius of the circular insert for a smooth transition from a transition curve to a circular curve. This leads to dangerous moments of the car's movement at the junction of the transition and circular curves. Therefore, we previously derived the formulas of refined braking transition curves that meet the requirements of the radii of classical transition curves [1, 2]. In addition, it later turned out that these refined transition curves have, as an additional effect, the property of reducing the area occupied by the left-turn exit, as shown in Fig. 1. We offer a method for optimizing the spatial parameters of cloverleaf interchanges with refined braking transition curves.