Olena Tsykolenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Olena Tsykolenko has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Kuzmych
Київський національний університет будівництва і архітектури
3 shared publications - Svitlana Bondar
Kyiv National University of Construction and Architecture
3 shared publications - Andriy Annenkov
Київський національний університет будівництва і архітектури
2 shared publications Олена Циколенко
Київський національний університет будівництва і архітектури
2 shared publications- Ihor Lapytskyi
Kyiv National University of Construction and Architecture
1 shared publication - Oleksandr Adamenko
Київський національний університет будівництва і архітектури
1 shared publication
Latest Publications
- Open Access
- 31 May 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 86,p. 388-396
ANALYSIS OF THE INFLUENCE OF EXTERNAL FACTORS ON THE DEFORMATION OF HIGH-RISE BUILDINGS IN THE PROCESS OF THEIR CONSTRUCTION AND OPERATION
During the construction and operation of high-rise buildings, their vertical axis changes its position in space. The greater the height of the structure, the greater the amplitude of oscillations. This causes problems of geodetic construction support and the need to monitor deformations during the operation of high-rise structures. In real conditions, part of the structures will be in the shade and their temperature will be lower than the structures that will be under the influence of solar radiation, the temperature of which will be much higher. Thus, the building will deform as a result of uneven thermal expansion, that is, it will bend. From DBN B.1.3-2:2010 "Geodesic works in construction". Also, during the geodetic provision of the construction and operation of high-rise buildings, changes in the temperature regime of building structures should be taken into account in connection with significant absolute values of changes in the geometric dimensions of the building as a result of thermal expansion, which significantly exceed the accuracy regulated by the regulatory document. The article examines and analyzes the influence of external forces on changes in the geometry of high-rise structures and focuses attention on solving the scientific problem of geodetic support for the construction and operation of modern high-rise structures under dynamic loads.
- 31 May 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 86,p. 388-396
Open AccessANALYSIS OF THE INFLUENCE OF EXTERNAL FACTORS ON THE DEFORMATION OF HIGH-RISE BUILDINGS IN THE PROCESS OF THEIR CONSTRUCTION AND OPERATION
During the construction and operation of high-rise buildings, their vertical axis changes its position in space. The greater the height of the structure, the greater the amplitude of oscillations. This causes problems of geodetic construction support and the need to monitor deformations during the operation of high-rise structures. In real conditions, part of the structures will be in the shade and their temperature will be lower than the structures that will be under the influence of solar radiation, the temperature of which will be much higher. Thus, the building will deform as a result of uneven thermal expansion, that is, it will bend. From DBN B.1.3-2:2010 "Geodesic works in construction". Also, during the geodetic provision of the construction and operation of high-rise buildings, changes in the temperature regime of building structures should be taken into account in connection with significant absolute values of changes in the geometric dimensions of the building as a result of thermal expansion, which significantly exceed the accuracy regulated by the regulatory document. The article examines and analyzes the influence of external forces on changes in the geometry of high-rise structures and focuses attention on solving the scientific problem of geodetic support for the construction and operation of modern high-rise structures under dynamic loads.
- Open Access
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 22-30
ANALYSIS OF METHODS FOR CONTROLLING METROLOGICAL CHARACTERISTICS OF LASER TRACKERS
Laser trackers are pivotal components within contemporary measurement technology, offering unparalleled precision and reliability in measurement processes. Yet, maintaining their effectiveness mandates a systematic approach to controlling their metrological traits. Both static and dynamic research methodologies are routinely employed to evaluate the accuracy of laser trackers. This article embarks on a detailed exploration of the methodologies employed to regulate the metrological attributes of laser trackers, encompassing the utilization of length artifacts, network methodologies, control mechanisms utilizing rotary tables, and interferometry techniques. By delving into these methodologies, the article endeavors to establish a robust framework for evaluating the accuracy and reliability of laser trackers. This process stands as a critical juncture in guaranteeing their effectiveness across various measurement tasks. The meticulous analysis of these methods is instrumental in enhancing the precision and dependability of laser trackers, thereby bolstering their utility across diverse industrial and scientific domains. Consequently, efforts directed towards refining the metrological characteristics of laser trackers play an indispensable role in the continuous advancement of measurement technology. They facilitate the seamless integration of laser trackers into an array of applications, ensuring their efficacy and reliability in addressing complex measurement challenges encountered in modern industries and scientific research endeavors. Лазерні трекери є ключовими пристроями у сучасній вимірювальній техніці, забезпечуючи високу точність і надійність у вимірюваннях. Однак, забезпечення їхньої ефективності вимагає систематичного контролю їхніх метрологічних характеристик. Статичні та динамічні дослідження є загальноприйнятими методами для оцінки точності вимірювань лазерними трекерами. В цій статті виконується аналіз методів контролю метрологічних характеристик лазерних трекерів, зокрема застосування матеріальної міри, мережевого методу, контролю з використанням поворотного столу та інтерферометра.
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 22-30
Open AccessANALYSIS OF METHODS FOR CONTROLLING METROLOGICAL CHARACTERISTICS OF LASER TRACKERS
Laser trackers are pivotal components within contemporary measurement technology, offering unparalleled precision and reliability in measurement processes. Yet, maintaining their effectiveness mandates a systematic approach to controlling their metrological traits. Both static and dynamic research methodologies are routinely employed to evaluate the accuracy of laser trackers. This article embarks on a detailed exploration of the methodologies employed to regulate the metrological attributes of laser trackers, encompassing the utilization of length artifacts, network methodologies, control mechanisms utilizing rotary tables, and interferometry techniques. By delving into these methodologies, the article endeavors to establish a robust framework for evaluating the accuracy and reliability of laser trackers. This process stands as a critical juncture in guaranteeing their effectiveness across various measurement tasks. The meticulous analysis of these methods is instrumental in enhancing the precision and dependability of laser trackers, thereby bolstering their utility across diverse industrial and scientific domains. Consequently, efforts directed towards refining the metrological characteristics of laser trackers play an indispensable role in the continuous advancement of measurement technology. They facilitate the seamless integration of laser trackers into an array of applications, ensuring their efficacy and reliability in addressing complex measurement challenges encountered in modern industries and scientific research endeavors. Лазерні трекери є ключовими пристроями у сучасній вимірювальній техніці, забезпечуючи високу точність і надійність у вимірюваннях. Однак, забезпечення їхньої ефективності вимагає систематичного контролю їхніх метрологічних характеристик. Статичні та динамічні дослідження є загальноприйнятими методами для оцінки точності вимірювань лазерними трекерами. В цій статті виконується аналіз методів контролю метрологічних характеристик лазерних трекерів, зокрема застосування матеріальної міри, мережевого методу, контролю з використанням поворотного столу та інтерферометра.
- Open Access
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 321-328
SEARCH OF OPTIMAL SPATIAL PARAMETERS FOR GEODETIC DELINEATION OF MOTORWAY INTERCHANGES WITH BRAKING TRANSITION CURVES
The most widespread grade-separated road junction — cloverleaf interchange — is a complex engineering structure, in which all the parameters and limitations of the plan and longitudinal profile must be coordinated with each other. The goals of the analysis: traffic safety, technical and economic indicators of the movement of transport units, the compactness of left-turn and right-turn exits and, as an additional, but extremely important aspect, the minimization of the area occupied by the entire transport structure, which is very important in tight urban conditions. First, let's emphasize that the trajectories of cars at the intersection must correspond to their real variable speeds on left-turn exits, since this is traffic on curves of small radii. In our previous studies, it has been experimentally proven that cars entering a left-turning exit reduce their speed, and conversely, when leaving the exit, their speed increases. Therefore, it is necessary to use braking curves as transition curves of left-turn exits, and not clothoid curves, which are often used, and which are designed for constant speed of movement. Some braking transition curves designed for variable speed are also used in traffic junctions [4]. But, analyzing these curves, we came to the conclusion that they do not meet the classical purpose of the transition curve, namely, they do not provide the necessary radius at the end of the curve, which is equal to the radius of the circular insert for a smooth transition from a transition curve to a circular curve. This leads to dangerous moments of the car's movement at the junction of the transition and circular curves. Therefore, we previously derived the formulas of refined braking transition curves that meet the requirements of the radii of classical transition curves [1, 2]. In addition, it later turned out that these refined transition curves have, as an additional effect, the property of reducing the area occupied by the left-turn exit, as shown in Fig. 1. We offer a method for optimizing the spatial parameters of cloverleaf interchanges with refined braking transition curves.
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 321-328
Open AccessSEARCH OF OPTIMAL SPATIAL PARAMETERS FOR GEODETIC DELINEATION OF MOTORWAY INTERCHANGES WITH BRAKING TRANSITION CURVES
The most widespread grade-separated road junction — cloverleaf interchange — is a complex engineering structure, in which all the parameters and limitations of the plan and longitudinal profile must be coordinated with each other. The goals of the analysis: traffic safety, technical and economic indicators of the movement of transport units, the compactness of left-turn and right-turn exits and, as an additional, but extremely important aspect, the minimization of the area occupied by the entire transport structure, which is very important in tight urban conditions. First, let's emphasize that the trajectories of cars at the intersection must correspond to their real variable speeds on left-turn exits, since this is traffic on curves of small radii. In our previous studies, it has been experimentally proven that cars entering a left-turning exit reduce their speed, and conversely, when leaving the exit, their speed increases. Therefore, it is necessary to use braking curves as transition curves of left-turn exits, and not clothoid curves, which are often used, and which are designed for constant speed of movement. Some braking transition curves designed for variable speed are also used in traffic junctions [4]. But, analyzing these curves, we came to the conclusion that they do not meet the classical purpose of the transition curve, namely, they do not provide the necessary radius at the end of the curve, which is equal to the radius of the circular insert for a smooth transition from a transition curve to a circular curve. This leads to dangerous moments of the car's movement at the junction of the transition and circular curves. Therefore, we previously derived the formulas of refined braking transition curves that meet the requirements of the radii of classical transition curves [1, 2]. In addition, it later turned out that these refined transition curves have, as an additional effect, the property of reducing the area occupied by the left-turn exit, as shown in Fig. 1. We offer a method for optimizing the spatial parameters of cloverleaf interchanges with refined braking transition curves.
- Open Access
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 111,p. 251-262
Monitoring of structures with bearing elements in the form of long vertical rods
A building structure is considered, which in the design form consists of two vertical rectilinear interacting elements. One of them is loading, the other is carrying. The bearing element is presented in the form of a long thin rod loaded with an external axial vertical force. Due to the errors of geodetic verification and installation work, the bearing rod will be installed with some inclination and displacement relative to the coordinate axes. The external load on the bearing element is represented by the force vector, which is equivalent to the loading rod. Errors of geodetic verification and installation work will change the design direction of the force line and its design position on the supporting element. An inclined force vector will have a vertical and horizontal force component. Thus, the line of action of the loading force and the longitudinal axis of the supporting rod will be located at an angle to each other, which will cause bending momentsand transverse forces in the sections of the rod. A design "changed" in relation to the project is created. Bending moments and horizontal forces in this design will contribute to premature bending of the rod. An unevenly heated rod also acquires the ability to distort. The influence of the specified factors can be increased, and the stability of the rod significantly weakened due to uneven subsidence, horizontal displacement or tilting of the supporting structure due to dangerous exogenous geological processes. Therefore, errors in the position of elements, changes in temperature, geological processes disrupt the linear form of equilibrium of the bearing rod and its position in space. The change in shape and relative position contributes to the premature emergence of an unstable state under an increasing external load. In the changed design, the bearing rod may suddenly find itself in a critical stress-deformed state. The task of monitoring is to sense and properly record changes and dynamics of the stress-strain state. For this purpose, measuring complexes with a certain configuration are designed, which provide with the necessary specified accuracy the measurement of changes in the physical state of the elements of building structures.
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 111,p. 251-262
Open AccessMonitoring of structures with bearing elements in the form of long vertical rods
A building structure is considered, which in the design form consists of two vertical rectilinear interacting elements. One of them is loading, the other is carrying. The bearing element is presented in the form of a long thin rod loaded with an external axial vertical force. Due to the errors of geodetic verification and installation work, the bearing rod will be installed with some inclination and displacement relative to the coordinate axes. The external load on the bearing element is represented by the force vector, which is equivalent to the loading rod. Errors of geodetic verification and installation work will change the design direction of the force line and its design position on the supporting element. An inclined force vector will have a vertical and horizontal force component. Thus, the line of action of the loading force and the longitudinal axis of the supporting rod will be located at an angle to each other, which will cause bending momentsand transverse forces in the sections of the rod. A design "changed" in relation to the project is created. Bending moments and horizontal forces in this design will contribute to premature bending of the rod. An unevenly heated rod also acquires the ability to distort. The influence of the specified factors can be increased, and the stability of the rod significantly weakened due to uneven subsidence, horizontal displacement or tilting of the supporting structure due to dangerous exogenous geological processes. Therefore, errors in the position of elements, changes in temperature, geological processes disrupt the linear form of equilibrium of the bearing rod and its position in space. The change in shape and relative position contributes to the premature emergence of an unstable state under an increasing external load. In the changed design, the bearing rod may suddenly find itself in a critical stress-deformed state. The task of monitoring is to sense and properly record changes and dynamics of the stress-strain state. For this purpose, measuring complexes with a certain configuration are designed, which provide with the necessary specified accuracy the measurement of changes in the physical state of the elements of building structures.