Zhiqiang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhiqiang Wang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chunyu He
State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China
5 shared publications - Junyi Luo
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
5 shared publications - Zhijie Jiao
State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China
5 shared publications - Zhiqiang Wu
State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China
5 shared publications - Zhong Zhao
State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China
5 shared publications - Chujie Liu
State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China
3 shared publications
Latest Publications
- Open Access
Intelligent Optimization Control of Plate Plan-View Pattern Based on Intermediate Slab Pattern Vision Inspection and BWO-DNN Algorithm
In the production process of plate, the main factors affecting the yield of plate are the crop-cutting and edge losses. It is very important to accurately predict the crop pattern of plates and effectively control the plan-view pattern. In this paper, a detection scheme is proposed to obtain the plan-view pattern of the intermediate slab and finished plate by placing detection devices after the roughing mill and finishing mill, respectively. An image processing algorithm is used to obtain a dataset of the plan-view pattern parameters, and a plan-view pattern prediction and control model for plate is established based on the BWO-DNN (beluga whale optimization–deep neural network) algorithm. The BWO algorithm is used to optimize the hyperparameters in the DNN algorithm to complete the establishment of the intelligent model. In terms of model analysis, goodness of fit (R2) and mean absolute error (MAE) are used as evaluation indicators. The results show that the intelligence model established based on BWO-DNN has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and parameter optimization of plan-view pattern control. The actual production verification on site shows that the irregular areas of the plate head and tail can be reduced by 17.2% and 22.6%, respectively.
Open AccessIntelligent Optimization Control of Plate Plan-View Pattern Based on Intermediate Slab Pattern Vision Inspection and BWO-DNN Algorithm
In the production process of plate, the main factors affecting the yield of plate are the crop-cutting and edge losses. It is very important to accurately predict the crop pattern of plates and effectively control the plan-view pattern. In this paper, a detection scheme is proposed to obtain the plan-view pattern of the intermediate slab and finished plate by placing detection devices after the roughing mill and finishing mill, respectively. An image processing algorithm is used to obtain a dataset of the plan-view pattern parameters, and a plan-view pattern prediction and control model for plate is established based on the BWO-DNN (beluga whale optimization–deep neural network) algorithm. The BWO algorithm is used to optimize the hyperparameters in the DNN algorithm to complete the establishment of the intelligent model. In terms of model analysis, goodness of fit (R2) and mean absolute error (MAE) are used as evaluation indicators. The results show that the intelligence model established based on BWO-DNN has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and parameter optimization of plan-view pattern control. The actual production verification on site shows that the irregular areas of the plate head and tail can be reduced by 17.2% and 22.6%, respectively.
- Open Access
- 29 May 2025
- Published by MDPI AG in Preprints.org
Intelligent Optimization Control of Plate Plan View Pattern Based on Intermediate Slab Pattern Vision Inspection and BWO-DNN Algorithm
In the production process of plate, the main factors affecting the yield of plate are the crop cutting and edge losses It is very important to accurately predict the crop pattern of plates and effectively control the plan view pattern. In this paper, a detection scheme is proposed to obtain plan view pattern of intermediate slab and finished plate by placing the detection devices after roughing mill and finishing mill respectively. The image processing algorithm is used to obtain the dataset of plan view pattern parameters, and the plan view pattern prediction and control model of plate is established based on BWO-DNN algorithm. The BWO algorithm is used to optimize the hyperparameters in DNN algorithm to complete the establishment of the intelligent model. In terms of model analysis, goodness of fit (R2) and mean absolute error (MAE) are used as evaluation indicators. The results show that the intelligence model established based on BWO-DNN has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and parameters optimization of plan view pattern control. The actual production verification on site shows that the irregular area of plate head and tail can be reduced by 17.2 % and 22.6% respectively.
- 29 May 2025
- Published by MDPI AG in Preprints.org
Open AccessIntelligent Optimization Control of Plate Plan View Pattern Based on Intermediate Slab Pattern Vision Inspection and BWO-DNN Algorithm
In the production process of plate, the main factors affecting the yield of plate are the crop cutting and edge losses It is very important to accurately predict the crop pattern of plates and effectively control the plan view pattern. In this paper, a detection scheme is proposed to obtain plan view pattern of intermediate slab and finished plate by placing the detection devices after roughing mill and finishing mill respectively. The image processing algorithm is used to obtain the dataset of plan view pattern parameters, and the plan view pattern prediction and control model of plate is established based on BWO-DNN algorithm. The BWO algorithm is used to optimize the hyperparameters in DNN algorithm to complete the establishment of the intelligent model. In terms of model analysis, goodness of fit (R2) and mean absolute error (MAE) are used as evaluation indicators. The results show that the intelligence model established based on BWO-DNN has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and parameters optimization of plan view pattern control. The actual production verification on site shows that the irregular area of plate head and tail can be reduced by 17.2 % and 22.6% respectively.
- Open Access
Rectangular Improvement Method for Plan View Pattern of Plates During the Angular Rolling Process
The effect of the angular rolling process on the plan view pattern of a plate was studied, and the rectangular influencing factors and improvement methods for this process were proposed in this paper. DEFORM (v11.0) finite element software was used to simulate the processes of conventional rolling and angular rolling, and the degree of rectangularity of plates under different rolling process conditions was compared. A formula to characterize the degree of rectangularity of plates was established; the closer this value is to one, the better the degree of rectangularity. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles was extended to obtain the optimum rectangular rotation angle using the finite element simulation method. In the two-pass angular rolling process, the optimal rectangular angle of the second pass was 14.275° when the first pass was 15°. The optimal rectangular angle of the plate was 19.008° when the first pass’ angle was 20°. Two-pass angular rolling is different to four-pass rolling, and the simulation results showed that (1.0012) was less than (1.0015) and (1.0034) was less than (1.0055). The rectangularity degree of the four-pass process was better than the two-pass process. Angular rolling experiments were carried out, and the actual data show that the characteristic rectangular value of the rolled piece was 1.003 during the four-pass process and 1.014 during the two-pass process. This verified that separating the one-group two-pass angular rolling process from the one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate, thereby increasing the yield rate. This provides a theoretical basis for industrial applications.Open AccessRectangular Improvement Method for Plan View Pattern of Plates During the Angular Rolling Process
The effect of the angular rolling process on the plan view pattern of a plate was studied, and the rectangular influencing factors and improvement methods for this process were proposed in this paper. DEFORM (v11.0) finite element software was used to simulate the processes of conventional rolling and angular rolling, and the degree of rectangularity of plates under different rolling process conditions was compared. A formula to characterize the degree of rectangularity of plates was established; the closer this value is to one, the better the degree of rectangularity. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles was extended to obtain the optimum rectangular rotation angle using the finite element simulation method. In the two-pass angular rolling process, the optimal rectangular angle of the second pass was 14.275° when the first pass was 15°. The optimal rectangular angle of the plate was 19.008° when the first pass’ angle was 20°. Two-pass angular rolling is different to four-pass rolling, and the simulation results showed that (1.0012) was less than (1.0015) and (1.0034) was less than (1.0055). The rectangularity degree of the four-pass process was better than the two-pass process. Angular rolling experiments were carried out, and the actual data show that the characteristic rectangular value of the rolled piece was 1.003 during the four-pass process and 1.014 during the two-pass process. This verified that separating the one-group two-pass angular rolling process from the one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate, thereby increasing the yield rate. This provides a theoretical basis for industrial applications. - Open Access
- 8 November 2024
- Published by MDPI AG in Preprints.org
Rectangular Improvement Method for Plan View Pattern of Plate During Angular Rolling Process
The effect of the angular rolling process on the plan view pattern of the plate is studied, the rectangular influence factor and improvement method for plate angular rolling process are proposed in this paper. Finite element models are established for the conventional rolling and angular rolling processes respectively, and with DEFORM software, the numerical simulation is carried out. A characterization formula reflecting the rectangular degree of the rolled piece is constructed and the rectangular degree of the plates under different rolling process conditions are compared. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles is extended to obtain the optimum rectangular rotation angle with finite element simulation method. The one-group two-pass angular rolling is separated to one-group four-pass rolling and the simulation results show that the rectangular degree of the four-pass process is better than the two-pass process. Angular rolling experiments are carried out, the actual data shows that the rectangular characteristic value of the rolled piece is 1.003 with the four-pass process, and 1.014 with the two-pass process. It verifies that with separating one-group two-pass angular rolling process to one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate.
- 8 November 2024
- Published by MDPI AG in Preprints.org
Open AccessRectangular Improvement Method for Plan View Pattern of Plate During Angular Rolling Process
The effect of the angular rolling process on the plan view pattern of the plate is studied, the rectangular influence factor and improvement method for plate angular rolling process are proposed in this paper. Finite element models are established for the conventional rolling and angular rolling processes respectively, and with DEFORM software, the numerical simulation is carried out. A characterization formula reflecting the rectangular degree of the rolled piece is constructed and the rectangular degree of the plates under different rolling process conditions are compared. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles is extended to obtain the optimum rectangular rotation angle with finite element simulation method. The one-group two-pass angular rolling is separated to one-group four-pass rolling and the simulation results show that the rectangular degree of the four-pass process is better than the two-pass process. Angular rolling experiments are carried out, the actual data shows that the rectangular characteristic value of the rolled piece is 1.003 with the four-pass process, and 1.014 with the two-pass process. It verifies that with separating one-group two-pass angular rolling process to one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate.
- Open Access
Digital Model of Plan View Pattern Control for Plate Mills Based on Machine Vision and the DBO-RBF Algorithm
Plan view pattern control (PVPC) is a highly effective means to improve the rectangularization of products and increase the yield of plate mills. By optimizing the parameters of PVPC, the effect of PVPC can be further improved. In this paper, a digital model for predicting and controlling crop patterns of plates is proposed based on the radial basis function (RBF) neural network optimized by the dung beetle optimizer (DBO) algorithm. Machine vision technology is used to obtain a digital description of the crop pattern of the rolled plates. An automatic threshold adjustment algorithm is proposed for the image processing of plate pattern photos during the rolling process. The error between the pattern data calculated through machine vision technology and the measured pattern data does not exceed 3 mm. The spread parameters of the RBF are optimized using DBO, and the digital model structure is established. The goodness of fit (R2) and the mean absolute error (MAE) are used as evaluation indicators. The results show that the digital model established based on DBO-RBF has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and the parameter optimization of PVPC. In practical applications, the crop cutting loss area of irregular deformation at the end of the plate can be reduced by 31%.
Open AccessDigital Model of Plan View Pattern Control for Plate Mills Based on Machine Vision and the DBO-RBF Algorithm
Plan view pattern control (PVPC) is a highly effective means to improve the rectangularization of products and increase the yield of plate mills. By optimizing the parameters of PVPC, the effect of PVPC can be further improved. In this paper, a digital model for predicting and controlling crop patterns of plates is proposed based on the radial basis function (RBF) neural network optimized by the dung beetle optimizer (DBO) algorithm. Machine vision technology is used to obtain a digital description of the crop pattern of the rolled plates. An automatic threshold adjustment algorithm is proposed for the image processing of plate pattern photos during the rolling process. The error between the pattern data calculated through machine vision technology and the measured pattern data does not exceed 3 mm. The spread parameters of the RBF are optimized using DBO, and the digital model structure is established. The goodness of fit (R2) and the mean absolute error (MAE) are used as evaluation indicators. The results show that the digital model established based on DBO-RBF has good predictive and control performance, realizing intelligent prediction of the crop pattern of plates and the parameter optimization of PVPC. In practical applications, the crop cutting loss area of irregular deformation at the end of the plate can be reduced by 31%.