Hongjun Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hongjun Zhang has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Chengtao Wang
Accelerator Division, Institute of High Energy Physics Chinese Academy of Sciences, Beijing, CHINA
6 shared publications - Qingjin Xu
Chinese Academy of Sciences
6 shared publications - Rui Kang
Institute of High Energy Physics Chinese Academy of Sciences, Beijing, China
6 shared publications - Jinrui Shi
Laboratory of Particle Acceleration Physics and Technology, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China
5 shared publications - Rui Ma
Laboratory of Particle Acceleration Physics and Technology, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China
5 shared publications - Xin Chen
Institute of High Energy Physics (IHEP), Chinese Academy of Sciences (CAS), Beijing, China
5 shared publications
Latest Publications
- Open Access
- 18 July 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (8) , 085021
Investigation of normal zone propagation velocity in AgSn/Ag/Ba122 superconducting tapes using a conduction cooling test system
The investigation of the behavior of quench propagation in iron-based superconducting (IBS) tapes is important for their application in magnets and the design of quench protection systems. However, little research has been done in this area. In this work, a conduction cooling test system for IBS tapes and coils has been built, which has functions such as charging test, temperature and voltage data acquisition, pulse current heating, quench detection and protection. A series of experiments were performed on several 27 cm long IBS tapes to measure their normal zone propagation velocity (NZPV). The variation trends of NZPV with different operating temperatures, and with different ratios of operating current to critical current were systematically explored. In addition, monitoring all the voltages between different positions of an IBS tape, including two joints, has provided more detailed results and findings.
- 18 July 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (8) , 085021
Open AccessInvestigation of normal zone propagation velocity in AgSn/Ag/Ba122 superconducting tapes using a conduction cooling test system
The investigation of the behavior of quench propagation in iron-based superconducting (IBS) tapes is important for their application in magnets and the design of quench protection systems. However, little research has been done in this area. In this work, a conduction cooling test system for IBS tapes and coils has been built, which has functions such as charging test, temperature and voltage data acquisition, pulse current heating, quench detection and protection. A series of experiments were performed on several 27 cm long IBS tapes to measure their normal zone propagation velocity (NZPV). The variation trends of NZPV with different operating temperatures, and with different ratios of operating current to critical current were systematically explored. In addition, monitoring all the voltages between different positions of an IBS tape, including two joints, has provided more detailed results and findings.
- 9 June 2024
- Published by Elsevier in Cryogenics
- Vol. 141
Charging delay elimination of solder impregnated HTS coils with specific excitation current
- 9 June 2024
- Published by Elsevier in Cryogenics
- Vol. 141
Charging delay elimination of solder impregnated HTS coils with specific excitation current
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Conceptual Design Study of a Superconducting Flywheel System With Enhanced Speed Using Dipole Field
The high temperature superconductivity (HTS) technology present itself a bright future to be used in a flywheel energy storage system (FESS). In addition to the characteristics of conventional flywheel energy storage systems, the self-stability of high temperature superconducting maglev enables the suspension bearing to completely eliminate external control, improving the efficiency and stability of the whole system. And superconducting flywheel energy storage system can effectively eliminate the loss caused by mechanical friction and the electrical loss caused by resistance. In this paper, a superconducting flywheel system which is suspended and self-stabilized through the meticulous design of a high magnetic field is presented. The most obvious advantages are the reduction of mechanical friction, the use of Lorentz force to provide centripetal force instead of relying on mechanical limit of materials, and a higher speed than traditional flywheels. The optimization of the field distribution as well as the HTS coil of the flywheel is discussed. Subsequently, the energy storage efficiency, power density, energy ratio and suspension force of the flywheel are analyzed and compared in detail.
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Conceptual Design Study of a Superconducting Flywheel System With Enhanced Speed Using Dipole Field
The high temperature superconductivity (HTS) technology present itself a bright future to be used in a flywheel energy storage system (FESS). In addition to the characteristics of conventional flywheel energy storage systems, the self-stability of high temperature superconducting maglev enables the suspension bearing to completely eliminate external control, improving the efficiency and stability of the whole system. And superconducting flywheel energy storage system can effectively eliminate the loss caused by mechanical friction and the electrical loss caused by resistance. In this paper, a superconducting flywheel system which is suspended and self-stabilized through the meticulous design of a high magnetic field is presented. The most obvious advantages are the reduction of mechanical friction, the use of Lorentz force to provide centripetal force instead of relying on mechanical limit of materials, and a higher speed than traditional flywheels. The optimization of the field distribution as well as the HTS coil of the flywheel is discussed. Subsequently, the energy storage efficiency, power density, energy ratio and suspension force of the flywheel are analyzed and compared in detail.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical Simulation of the Mechanical Behavior of a Transposed Cable With the In-Plane Bending of ReBCO Tapes
The Institute of High Energy Physics, Chinese Academy of Sciences (IEHP, CAS) proposed a compact ReBCO cable (named X-cable) which is implemented by in-plane bending ReBCO tapes to realize the transposition, and successfully fabricated a 10 m length prototype cable. The study on the mechanical properties of the cable is of great significance to its engineering application. Based on the finite element model, the stress-strain state of cable under different loads has been analyzed, which are used to predict the critical current performance of superconducting tapes in cable. This paper focuses on the possible failure mechanism of the X-cable under bending and transverse loads. Based on the established model, the critical bending radius of the x-cable is determined to be 20 mm. We analyzed the critical pressure and shear stress of the cable under lateral load, considering two possible scenarios that may occur during the manufacturing process. The above results can serve as a valuable reference for subsequent design of magnets and winding of coils.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical Simulation of the Mechanical Behavior of a Transposed Cable With the In-Plane Bending of ReBCO Tapes
The Institute of High Energy Physics, Chinese Academy of Sciences (IEHP, CAS) proposed a compact ReBCO cable (named X-cable) which is implemented by in-plane bending ReBCO tapes to realize the transposition, and successfully fabricated a 10 m length prototype cable. The study on the mechanical properties of the cable is of great significance to its engineering application. Based on the finite element model, the stress-strain state of cable under different loads has been analyzed, which are used to predict the critical current performance of superconducting tapes in cable. This paper focuses on the possible failure mechanism of the X-cable under bending and transverse loads. Based on the established model, the critical bending radius of the x-cable is determined to be 20 mm. We analyzed the critical pressure and shear stress of the cable under lateral load, considering two possible scenarios that may occur during the manufacturing process. The above results can serve as a valuable reference for subsequent design of magnets and winding of coils.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design, Simulation and Test Results of Quench Protection System for a 13-T Twin-Aperture Superconducting Dipole Magnet
On the basis of the successful development of a high field dipole magnet named LPF1-U, which reached a peak field of 12.47 T in 2021, the new magnet LPF3 with an expected field of over 13 T in the two 50-mm apertures has been designed and fabricated at IHEP. The magnet is developed in a common-coil configuration with six flat racetrack Nb 3 Sn coils, as well as High Temperature Superconducting (HTS) insert coils in the center to further enhance the field to 16 T or more. The Nb 3 Sn coils are designed to provide a 13 T main field at the operating current of 7580 A. The quench protection of the Nb 3 Sn coils is significantly important and challenging because of the much larger magnet apertures (50 mm) and stored energy (2155 kJ). Finally, the method of CLIQ (coupling-loss induced quench protection system) together with varistor is adopted to accelerate the propagation of quench in the magnet and control the hotspot temperature. This article describes the design of the optimized quench protection scheme, the model and the simulation results. The experiment test results are also analyzed and discussed in this article.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design, Simulation and Test Results of Quench Protection System for a 13-T Twin-Aperture Superconducting Dipole Magnet
On the basis of the successful development of a high field dipole magnet named LPF1-U, which reached a peak field of 12.47 T in 2021, the new magnet LPF3 with an expected field of over 13 T in the two 50-mm apertures has been designed and fabricated at IHEP. The magnet is developed in a common-coil configuration with six flat racetrack Nb 3 Sn coils, as well as High Temperature Superconducting (HTS) insert coils in the center to further enhance the field to 16 T or more. The Nb 3 Sn coils are designed to provide a 13 T main field at the operating current of 7580 A. The quench protection of the Nb 3 Sn coils is significantly important and challenging because of the much larger magnet apertures (50 mm) and stored energy (2155 kJ). Finally, the method of CLIQ (coupling-loss induced quench protection system) together with varistor is adopted to accelerate the propagation of quench in the magnet and control the hotspot temperature. This article describes the design of the optimized quench protection scheme, the model and the simulation results. The experiment test results are also analyzed and discussed in this article.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical and Experimental Analysis of Thermomagnetic Instability in Nb3Sn Wires
Nb 3 Sn is now recognized as the practical material for the high-field applications from 10 to 16 T, for particle accelerators, fusion and other related fields. However, the obtaining of high J c in Nb 3 Sn presently contradicts one of the most important stability criteria: to keep a small filament size, which makes the stability issue particularly prominent. Large filament sizes frequently cause flux jumps in the conductor, making quench detection and protection more challenging for Nb 3 Sn magnets. In this work, we try to numerically simulate the flux jumps more accurately down to a filamentary scale. Based on the theory of superconducting dynamics, we have established a theoretical model to describe the magnetothermal instability of Nb 3 Sn wires by considering the superconductor flux dynamics, heat diffusion and temperature response. The preliminary analysis of the test results for LPF3 which is a 16-T hybrid common coil dipole magnet fabricated by Institute of High Energy Physics is conducted to study the causes of its quenching and the impact of flux jumps on the magnet.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical and Experimental Analysis of Thermomagnetic Instability in Nb3Sn Wires
Nb 3 Sn is now recognized as the practical material for the high-field applications from 10 to 16 T, for particle accelerators, fusion and other related fields. However, the obtaining of high J c in Nb 3 Sn presently contradicts one of the most important stability criteria: to keep a small filament size, which makes the stability issue particularly prominent. Large filament sizes frequently cause flux jumps in the conductor, making quench detection and protection more challenging for Nb 3 Sn magnets. In this work, we try to numerically simulate the flux jumps more accurately down to a filamentary scale. Based on the theory of superconducting dynamics, we have established a theoretical model to describe the magnetothermal instability of Nb 3 Sn wires by considering the superconductor flux dynamics, heat diffusion and temperature response. The preliminary analysis of the test results for LPF3 which is a 16-T hybrid common coil dipole magnet fabricated by Institute of High Energy Physics is conducted to study the causes of its quenching and the impact of flux jumps on the magnet.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet With Graded Common-Coil Configuration
R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for pre-study of the next-generation high energy colliders like Super Proton-Proton Collider (SPPC), Future Circular Collider (FCC) and etc. A 12.47-T main field at 4.2 K has been attained in 2021 within two 14-mm apertures of LPF1-U, a superconducting model dipole magnet with Nb 3 Sn & NbTi combined common-coil configuration. Based on the experiences mastered in the LPF1 series magnets, a 16-T high field dipole magnet named LPF3 has been designed, fabricated and is in the performance test process. LPF3 is also a combined magnet with six racetrack Nb 3 Sn coils outside, expected to provide a 13-T main field within two 50-mm apertures, and with inserted HTS coils to enhance the field up to 16 T or even higher. The 13-T Nb 3 Sn dipole magnet, named LPF3-LTS, incorporates a graded common-coil configuration to enhance superconductor efficiency. The optimization of coil layouts includes varying bending radii (BR) and lengths of straight sections (LSS) to mitigate field accumulation in the outer four coils near the central posts and coil ends, respectively. Several Rutherford cables over 200 meters were fabricated for the coils winding, and with the maximum strands count of 42. The support structure for LPF3-LTS has adopted a shell-based design, with an improved “Bladder & Key” technology. Dedicated hydraulic pistons were investigated and utilized to replace the traditional bladders. The main design characteristics, fabrication process and some preliminary test results of the magnet are presented in this paper.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet With Graded Common-Coil Configuration
R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for pre-study of the next-generation high energy colliders like Super Proton-Proton Collider (SPPC), Future Circular Collider (FCC) and etc. A 12.47-T main field at 4.2 K has been attained in 2021 within two 14-mm apertures of LPF1-U, a superconducting model dipole magnet with Nb 3 Sn & NbTi combined common-coil configuration. Based on the experiences mastered in the LPF1 series magnets, a 16-T high field dipole magnet named LPF3 has been designed, fabricated and is in the performance test process. LPF3 is also a combined magnet with six racetrack Nb 3 Sn coils outside, expected to provide a 13-T main field within two 50-mm apertures, and with inserted HTS coils to enhance the field up to 16 T or even higher. The 13-T Nb 3 Sn dipole magnet, named LPF3-LTS, incorporates a graded common-coil configuration to enhance superconductor efficiency. The optimization of coil layouts includes varying bending radii (BR) and lengths of straight sections (LSS) to mitigate field accumulation in the outer four coils near the central posts and coil ends, respectively. Several Rutherford cables over 200 meters were fabricated for the coils winding, and with the maximum strands count of 42. The support structure for LPF3-LTS has adopted a shell-based design, with an improved “Bladder & Key” technology. Dedicated hydraulic pistons were investigated and utilized to replace the traditional bladders. The main design characteristics, fabrication process and some preliminary test results of the magnet are presented in this paper.