Huafang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Huafang Wang has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Jijun Lu
School of Mechanical Engineering and Automation, Wuhan Textile University, China
5 shared publications - Lei Yang
School of Mechanical Engineering and Automation, Wuhan Textile University, China
3 shared publications Ao Xue
School of Mechanical Engineering and Automation, Wuhan Textile University, China
2 shared publicationsWei He
School of Mechanical Engineering and Automation, Wuhan Textile University, Wuhan, China
2 shared publications- Xin He
School of Applied Physics and Materials Wuyi University Jiangmen P.R. China
2 shared publications Yuhan Tang
School of Mechanical Engineering and Automation, Wuhan Textile University, China
2 shared publications
Latest Publications
- 26 April 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (1) , 553-565
Fabrication of High-strength and Lightweight Ceramsite from Foundry Solid Waste: Material Design and Forming Mechanism
- 26 April 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (1) , 553-565
Fabrication of High-strength and Lightweight Ceramsite from Foundry Solid Waste: Material Design and Forming Mechanism
- 10 October 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (3) , 94-100
Effect of Span-80 to Moisture Resistance of Near-infrared Curing 3D Printing Sodium Silicate Foundry Sands
In this work, a new method of near-infrared curing 3D printing sodium silicate sands (NIRC3DPSSS) driven by photovoltaic cells was proposed, and the Span-80 moisture resistance modifier was studied. NIRC3DPSSS had the advantages of high strength, rapid curing and low residual strength. However, the 24h storage strength would reduce because Na+ in the bonding bridges could absorb moisture. The experimental results showed that the strength of Span-80 modified sands molds reached 0.95MPa after 4 hours in a humidistat with 99%RH (relative humidity) containing 2.2% sodium silicate, an increase of 97.9% comparing to common sands molds. In air(80%RH), the strength reached 1.25MPa, an increase of 40.4%. The optimal effect of modification was achieved when Span-80 was 0.066% of the raw sands. Additionally, the bonding film and bridges in sodium silicate sands modified with Span-80 were more stable, smoother and free of cracks when observed using scanning electron microscopy (SEM) and energy dispersive spectroscopy(EDS).
- 10 October 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (3) , 94-100
Effect of Span-80 to Moisture Resistance of Near-infrared Curing 3D Printing Sodium Silicate Foundry Sands
In this work, a new method of near-infrared curing 3D printing sodium silicate sands (NIRC3DPSSS) driven by photovoltaic cells was proposed, and the Span-80 moisture resistance modifier was studied. NIRC3DPSSS had the advantages of high strength, rapid curing and low residual strength. However, the 24h storage strength would reduce because Na+ in the bonding bridges could absorb moisture. The experimental results showed that the strength of Span-80 modified sands molds reached 0.95MPa after 4 hours in a humidistat with 99%RH (relative humidity) containing 2.2% sodium silicate, an increase of 97.9% comparing to common sands molds. In air(80%RH), the strength reached 1.25MPa, an increase of 40.4%. The optimal effect of modification was achieved when Span-80 was 0.066% of the raw sands. Additionally, the bonding film and bridges in sodium silicate sands modified with Span-80 were more stable, smoother and free of cracks when observed using scanning electron microscopy (SEM) and energy dispersive spectroscopy(EDS).
- Open Access
- 24 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (3) , 851-858
Tribological Behaviors of Oxynitride Coating on TC4 Alloy Prepared by Double Glow Technology
The oxynitride coating was fabricated on the surface of Ti6Al4V alloy via double glow plasma alloy technology to enhance the wear resistance. The protective coating is dense and homogeneous and has a multilayer structure (outermost oxygen-rich layer, middle nitrogen-rich layer, innermost nitrogen diffusion layer). The acoustic emission curve suggests that the critical load is 53.1 N, the bonding strength between oxynitride coating and substrate is adequate to the application due to the diffusion layer. The oxynitride coating has a maximum hardness about 1020 HV, which is significant harder than Ti6Al4V alloy (370 HV). Tribological behaviors of oxynitride coating were investigated at three loads. The results indicated that the friction coefficient of oxynitride coating is lower than that of substrate at the same conditions. The wear mechanism of oxynitride coating is mainly fatigue wear, which converts to adhesive wear and fatigue wear with increasing load. The protective layer can decrease the actual contact areas obviously during the wear tests, which attributed to the higher hardness and stability of oxynitride layer.
- 24 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (3) , 851-858
Open AccessTribological Behaviors of Oxynitride Coating on TC4 Alloy Prepared by Double Glow Technology
The oxynitride coating was fabricated on the surface of Ti6Al4V alloy via double glow plasma alloy technology to enhance the wear resistance. The protective coating is dense and homogeneous and has a multilayer structure (outermost oxygen-rich layer, middle nitrogen-rich layer, innermost nitrogen diffusion layer). The acoustic emission curve suggests that the critical load is 53.1 N, the bonding strength between oxynitride coating and substrate is adequate to the application due to the diffusion layer. The oxynitride coating has a maximum hardness about 1020 HV, which is significant harder than Ti6Al4V alloy (370 HV). Tribological behaviors of oxynitride coating were investigated at three loads. The results indicated that the friction coefficient of oxynitride coating is lower than that of substrate at the same conditions. The wear mechanism of oxynitride coating is mainly fatigue wear, which converts to adhesive wear and fatigue wear with increasing load. The protective layer can decrease the actual contact areas obviously during the wear tests, which attributed to the higher hardness and stability of oxynitride layer.
- Open Access
- 24 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (3) , 1005-1014
Effect of Particle Size, Lubricant, and Heat Temperature on the Flowability of Ni-Based Powders for Additive Manufacturing
Gas-atomized Ni-based powder tends to agglomerate, directly impacting the spreadability of printing process. In this paper, three technical methods are applied to restore the powder flowability, including regulating particle size distribution, lubricant modification, and heating treatment. As particle size increases, powder regains flowability. However, the average particle size of GH3536 powders with flowability is greater than 46 μm, which cannot meet the demand for 3D printing (15-53 μm). The flowability of GH3536 powder can be restored by adding zinc stearate lubricant. After lubricant modification, the printed samples display a 16% increase in elongation, along with a little improvement in tensile strength. This paper also investigates the flow properties change of raw powder heated at 100°C, 200°C, 300°C, and 400°C. When the temperature rises beyond 400°C, powder flowability fully returns, along with oxygen content increasing. Overall, the lubricant modification technique is appropriate in actual manufacturing, but the flow rate value of powders is typically high, exceeding 70 s/50 g. Increasing particle size and heat treatment can improve powder flowability and the flow rate of powder is less than 20 s/50 g.
- 24 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (3) , 1005-1014
Open AccessEffect of Particle Size, Lubricant, and Heat Temperature on the Flowability of Ni-Based Powders for Additive Manufacturing
Gas-atomized Ni-based powder tends to agglomerate, directly impacting the spreadability of printing process. In this paper, three technical methods are applied to restore the powder flowability, including regulating particle size distribution, lubricant modification, and heating treatment. As particle size increases, powder regains flowability. However, the average particle size of GH3536 powders with flowability is greater than 46 μm, which cannot meet the demand for 3D printing (15-53 μm). The flowability of GH3536 powder can be restored by adding zinc stearate lubricant. After lubricant modification, the printed samples display a 16% increase in elongation, along with a little improvement in tensile strength. This paper also investigates the flow properties change of raw powder heated at 100°C, 200°C, 300°C, and 400°C. When the temperature rises beyond 400°C, powder flowability fully returns, along with oxygen content increasing. Overall, the lubricant modification technique is appropriate in actual manufacturing, but the flow rate value of powders is typically high, exceeding 70 s/50 g. Increasing particle size and heat treatment can improve powder flowability and the flow rate of powder is less than 20 s/50 g.
- 11 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (2) , 117-123
Bio-regeneration for Sodium Silicate Used Sands and its Unattended Monitoring System
- 11 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (2) , 117-123
Bio-regeneration for Sodium Silicate Used Sands and its Unattended Monitoring System
- 18 March 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (1) , 129-134
Application of Arc Furnace Flue Ash in Casting Heat Insulation Riser
- 18 March 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 24 (1) , 129-134
Application of Arc Furnace Flue Ash in Casting Heat Insulation Riser
- 6 November 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 22 (3) , 99-106
Study on Reclamation of CO 2-hardened Sodium Silicate Used Sands by CaO Powder
- 6 November 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 22 (3) , 99-106
Study on Reclamation of CO 2-hardened Sodium Silicate Used Sands by CaO Powder
- 1 November 2023
- Published by Springer Nature in China Foundry
- Vol. 20 (6) , 537-544
Reclamation of CO2 sodium silicate used sands by steam leaching
- 1 November 2023
- Published by Springer Nature in China Foundry
- Vol. 20 (6) , 537-544
Reclamation of CO2 sodium silicate used sands by steam leaching
- 27 December 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 75-82
Preparation and Performance Optimization of Organosilicon Slag Exothermic Insulating Riser
- 27 December 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 75-82
Preparation and Performance Optimization of Organosilicon Slag Exothermic Insulating Riser