Douglas Straub
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Douglas Straub has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Matthew Searle
National Energy Technology Lab. (NETL), Morgantown, WV (United States)
9 shared publications Owen Grabowski
NETL Site Support Contractor, National Energy Technology Laboratory
4 shared publicationsForrest Ames
NETL Site Support Contractor, National Energy Technology Laboratory
3 shared publicationsMatthew Krull
Pennsylvania State University (PSU)
3 shared publicationsRachel Ross
Pennsylvania State University (PSU)
3 shared publicationsStephen Lynch
Pennsylvania State University (PSU)
3 shared publications
Latest Publications
- 21 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Identifying the Accuracy of Surface Roughness for Metal Additive Manufacturing Parts Captured with Computed Tomography Scanning
Conventional surface roughness measurement techniques require direct access to internal surfaces, often necessitating destructive sectioning of test articles. Computed tomography (CT) offers a non-destructive alternative for internal surface characterization, but its application in metrology remains unstandardized and sensitive to machine resolution and operator technique. This study investigates the feasibility of using CT scanning to quantify areal surface roughness in metal AM heat exchanger tubes with three distinct internal geometries: ribbed, discrete W, and featureless. CT-derived surface parameters were extracted using custom Python scripts and compared to measurements obtained from a focus variation microscope calibrated against a known standard. Results show that CT-based roughness measurements closely matched microscope values for the discrete W specimen, deviations between CT and microscope measurements were minimal—less than 1 µm—indicating reliable reconstruction. In contrast, the ribbed and featureless specimens, with lower roughness values showed greater discrepancies. The findings suggest that CT scanning can be a viable non-destructive metrology tool for AM parts with surface roughness above approximately 8 µm. For smoother surfaces, current CT capabilities may not provide sufficient accuracy, highlighting the need for resolution-aware workflows and further standardization in CT-based surface metrology.
- 21 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Identifying the Accuracy of Surface Roughness for Metal Additive Manufacturing Parts Captured with Computed Tomography Scanning
Conventional surface roughness measurement techniques require direct access to internal surfaces, often necessitating destructive sectioning of test articles. Computed tomography (CT) offers a non-destructive alternative for internal surface characterization, but its application in metrology remains unstandardized and sensitive to machine resolution and operator technique. This study investigates the feasibility of using CT scanning to quantify areal surface roughness in metal AM heat exchanger tubes with three distinct internal geometries: ribbed, discrete W, and featureless. CT-derived surface parameters were extracted using custom Python scripts and compared to measurements obtained from a focus variation microscope calibrated against a known standard. Results show that CT-based roughness measurements closely matched microscope values for the discrete W specimen, deviations between CT and microscope measurements were minimal—less than 1 µm—indicating reliable reconstruction. In contrast, the ribbed and featureless specimens, with lower roughness values showed greater discrepancies. The findings suggest that CT scanning can be a viable non-destructive metrology tool for AM parts with surface roughness above approximately 8 µm. For smoother surfaces, current CT capabilities may not provide sufficient accuracy, highlighting the need for resolution-aware workflows and further standardization in CT-based surface metrology.
- Open Access
- 27 August 2025
- Published by Office of Scientific and Technical Information (OSTI)
Heat Transfer of Supercritical Carbon Dioxide in 3D-Printed Tubes with Internal Ribs and Yttria Stabilized Zirconia Coating
This technical report describes measurements performed in NETL’s Heat Exchanger Experimental Test (HEET) facility using supercritical carbon dioxide as the working fluid. 3D printed tubes with internal ribs and yttria stabilized zirconia (YSZ) exterior coatings were employed in the heat exchanger. Heat transfer and friction factor enhancements from the internal ribs were characterized over a range of flow conditions. Additionally, the thermal resistance from the YSZ coating was characterized for both a freshly applied coating and a coating subjected to thermal aging.
- 27 August 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessHeat Transfer of Supercritical Carbon Dioxide in 3D-Printed Tubes with Internal Ribs and Yttria Stabilized Zirconia Coating
This technical report describes measurements performed in NETL’s Heat Exchanger Experimental Test (HEET) facility using supercritical carbon dioxide as the working fluid. 3D printed tubes with internal ribs and yttria stabilized zirconia (YSZ) exterior coatings were employed in the heat exchanger. Heat transfer and friction factor enhancements from the internal ribs were characterized over a range of flow conditions. Additionally, the thermal resistance from the YSZ coating was characterized for both a freshly applied coating and a coating subjected to thermal aging.
- Open Access
- 9 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Technologies for Enhanced Condensation in sCO2 Power Cycles
The direct fired supercritical carbon dioxide power cycle has higher efficiency, compact machinery footprint, and is resilient under transient operation. It has been shown that improving the cycle main cooler significantly improves performance, including increased cycle efficiency, decreased cost of electricity and decreased cooler outlet temperatures. One way to improve this process is through enhanced condensation techniques and management of condensation fluid. This manuscript provides an overview of active and passive enhanced condensation technologies, with a focus on the passive approaches. compared to passive approaches, active approaches can have higher heat transfer enhancement, but the additional power and infrastructure can be problematic. The passive approaches identified include microfins (helical and herringbone), corrugated tubing, dimpled tubing and pin fins. After comparison it is found that the microfin geometry has the best performance characteristics followed by the additively manufactured pin fins. It is noted that current literature around additively manufactured enhancements is lacking, and investigation of conventional as well as novel geometries fabricated in this manner may be worth further investigation. Benchmark correlations for these geometries are identified and their limitations outlined. For further investigation, a matrix of test articles is presented for possible experimentation.
- 9 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessTechnologies for Enhanced Condensation in sCO2 Power Cycles
The direct fired supercritical carbon dioxide power cycle has higher efficiency, compact machinery footprint, and is resilient under transient operation. It has been shown that improving the cycle main cooler significantly improves performance, including increased cycle efficiency, decreased cost of electricity and decreased cooler outlet temperatures. One way to improve this process is through enhanced condensation techniques and management of condensation fluid. This manuscript provides an overview of active and passive enhanced condensation technologies, with a focus on the passive approaches. compared to passive approaches, active approaches can have higher heat transfer enhancement, but the additional power and infrastructure can be problematic. The passive approaches identified include microfins (helical and herringbone), corrugated tubing, dimpled tubing and pin fins. After comparison it is found that the microfin geometry has the best performance characteristics followed by the additively manufactured pin fins. It is noted that current literature around additively manufactured enhancements is lacking, and investigation of conventional as well as novel geometries fabricated in this manner may be worth further investigation. Benchmark correlations for these geometries are identified and their limitations outlined. For further investigation, a matrix of test articles is presented for possible experimentation.
- 30 January 2025
- Published by Office of Scientific and Technical Information (OSTI)
Simple Heat Transfer Model for Film Cooling Applications
- 30 January 2025
- Published by Office of Scientific and Technical Information (OSTI)
Simple Heat Transfer Model for Film Cooling Applications
- Open Access
- 24 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Leveraging Additive Manufacturing and Coatings for Turbine Thermal Management
This presentation provides an update to the University Turbine Systems Research meeting on research performed at NETL in areas of sCO2 heat transfer for direct cycle power generation and aerothermal research to improve the efficiency and reduce emissions of small gas turbines. Specific topics include a novel test approach to measure the performance of a thermal barrier coating in-situ and fabrication of advanced, additively manufactured airfoils for testing in a high speed cascade.
- 24 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessLeveraging Additive Manufacturing and Coatings for Turbine Thermal Management
This presentation provides an update to the University Turbine Systems Research meeting on research performed at NETL in areas of sCO2 heat transfer for direct cycle power generation and aerothermal research to improve the efficiency and reduce emissions of small gas turbines. Specific topics include a novel test approach to measure the performance of a thermal barrier coating in-situ and fabrication of advanced, additively manufactured airfoils for testing in a high speed cascade.
- 6 January 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 241
Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator
- 6 January 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 241
Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator
- Open Access
- 7 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Surface Roughness Effects on Heat Transfer in Additively Manufactured sCO2 Cycle Heat Exchangers
An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO2) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% less than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt numbr augmentation results. These results indicated a 10% improvement in heat duty for a heat exchangermore » constructed utilizing a tube with relative to a heat exchanger utilizing a smooth, conventional tube. « less
- 7 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessSurface Roughness Effects on Heat Transfer in Additively Manufactured sCO2 Cycle Heat Exchangers
An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO2) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% less than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt numbr augmentation results. These results indicated a 10% improvement in heat duty for a heat exchangermore » constructed utilizing a tube with relative to a heat exchanger utilizing a smooth, conventional tube. « less