Matthew Searle
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Matthew Searle has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Douglas Straub
NETL
9 shared publications - Arnab Roy
Department of Mechanical Engineering, Virginia Tech, Blacksburg, VA 24061
3 shared publications Forrest Ames
NETL Site Support Contractor, National Energy Technology Laboratory
3 shared publicationsMatthew Krull
Pennsylvania State University (PSU)
3 shared publicationsOwen Grabowski
National Energy Technology Laboratory (NETL), Pittsburgh, PA, Morgantown, WV, and Albany, OR (United States)
3 shared publicationsRachel Ross
Pennsylvania State University (PSU)
3 shared publications
Latest Publications
- Open Access
- 27 August 2025
- Published by Office of Scientific and Technical Information (OSTI)
Heat Transfer of Supercritical Carbon Dioxide in 3D-Printed Tubes with Internal Ribs and Yttria Stabilized Zirconia Coating
This technical report describes measurements performed in NETL’s Heat Exchanger Experimental Test (HEET) facility using supercritical carbon dioxide as the working fluid. 3D printed tubes with internal ribs and yttria stabilized zirconia (YSZ) exterior coatings were employed in the heat exchanger. Heat transfer and friction factor enhancements from the internal ribs were characterized over a range of flow conditions. Additionally, the thermal resistance from the YSZ coating was characterized for both a freshly applied coating and a coating subjected to thermal aging.
- 27 August 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessHeat Transfer of Supercritical Carbon Dioxide in 3D-Printed Tubes with Internal Ribs and Yttria Stabilized Zirconia Coating
This technical report describes measurements performed in NETL’s Heat Exchanger Experimental Test (HEET) facility using supercritical carbon dioxide as the working fluid. 3D printed tubes with internal ribs and yttria stabilized zirconia (YSZ) exterior coatings were employed in the heat exchanger. Heat transfer and friction factor enhancements from the internal ribs were characterized over a range of flow conditions. Additionally, the thermal resistance from the YSZ coating was characterized for both a freshly applied coating and a coating subjected to thermal aging.
- Open Access
- 9 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Technologies for Enhanced Condensation in sCO2 Power Cycles
The direct fired supercritical carbon dioxide power cycle has higher efficiency, compact machinery footprint, and is resilient under transient operation. It has been shown that improving the cycle main cooler significantly improves performance, including increased cycle efficiency, decreased cost of electricity and decreased cooler outlet temperatures. One way to improve this process is through enhanced condensation techniques and management of condensation fluid. This manuscript provides an overview of active and passive enhanced condensation technologies, with a focus on the passive approaches. compared to passive approaches, active approaches can have higher heat transfer enhancement, but the additional power and infrastructure can be problematic. The passive approaches identified include microfins (helical and herringbone), corrugated tubing, dimpled tubing and pin fins. After comparison it is found that the microfin geometry has the best performance characteristics followed by the additively manufactured pin fins. It is noted that current literature around additively manufactured enhancements is lacking, and investigation of conventional as well as novel geometries fabricated in this manner may be worth further investigation. Benchmark correlations for these geometries are identified and their limitations outlined. For further investigation, a matrix of test articles is presented for possible experimentation.
- 9 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessTechnologies for Enhanced Condensation in sCO2 Power Cycles
The direct fired supercritical carbon dioxide power cycle has higher efficiency, compact machinery footprint, and is resilient under transient operation. It has been shown that improving the cycle main cooler significantly improves performance, including increased cycle efficiency, decreased cost of electricity and decreased cooler outlet temperatures. One way to improve this process is through enhanced condensation techniques and management of condensation fluid. This manuscript provides an overview of active and passive enhanced condensation technologies, with a focus on the passive approaches. compared to passive approaches, active approaches can have higher heat transfer enhancement, but the additional power and infrastructure can be problematic. The passive approaches identified include microfins (helical and herringbone), corrugated tubing, dimpled tubing and pin fins. After comparison it is found that the microfin geometry has the best performance characteristics followed by the additively manufactured pin fins. It is noted that current literature around additively manufactured enhancements is lacking, and investigation of conventional as well as novel geometries fabricated in this manner may be worth further investigation. Benchmark correlations for these geometries are identified and their limitations outlined. For further investigation, a matrix of test articles is presented for possible experimentation.
- 30 January 2025
- Published by Office of Scientific and Technical Information (OSTI)
Simple Heat Transfer Model for Film Cooling Applications
- 30 January 2025
- Published by Office of Scientific and Technical Information (OSTI)
Simple Heat Transfer Model for Film Cooling Applications
- Open Access
- 24 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Leveraging Additive Manufacturing and Coatings for Turbine Thermal Management
This presentation provides an update to the University Turbine Systems Research meeting on research performed at NETL in areas of sCO2 heat transfer for direct cycle power generation and aerothermal research to improve the efficiency and reduce emissions of small gas turbines. Specific topics include a novel test approach to measure the performance of a thermal barrier coating in-situ and fabrication of advanced, additively manufactured airfoils for testing in a high speed cascade.
- 24 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessLeveraging Additive Manufacturing and Coatings for Turbine Thermal Management
This presentation provides an update to the University Turbine Systems Research meeting on research performed at NETL in areas of sCO2 heat transfer for direct cycle power generation and aerothermal research to improve the efficiency and reduce emissions of small gas turbines. Specific topics include a novel test approach to measure the performance of a thermal barrier coating in-situ and fabrication of advanced, additively manufactured airfoils for testing in a high speed cascade.
- 6 January 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 241
Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator
- 6 January 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 241
Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator
- 23 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (11)
Investigation of Gas Turbine Internal Cooling Using Supercritical CO2—Effect of Surface Roughness and Channel Aspect Ratio
Experimental and numerical investigation of internal cooling channels with rib turbulators is presented with sCO2 flow at pressure-20.7MPa and temperature up to 150°C. The effect of channel aspect ratio up to 2:1 on thermal-hydraulic performance is explored in additively manufactured rectangular and square channels, both with and without 60° ribs on the top and bottom sides. The Wilson-plot method is employed to measure channel averaged Nusselt number over a Reynolds number range up to 370,000. The friction factor and the overall thermal performance factor (TPF) are also reported. The computational fluid dynamics (CFD) simulation is performed for the rib-turbulated configurations reported in the experiments. The objective of the numerical study is to gain insight into the local heat transfer augmentation in the ribbed channels varying the aspect ratio, channel configuration, operating conditions and surface roughness. Surface roughness is simulated using sand grain roughness height (Ks) calculated from the experimental data, and a comparison is presented with varying surface roughness heights ranging between Ks = 0 - 40µm. Experimental results indicate that the heat transfer augmentation is negligible in the rectangular channels with ribs on the long side compared to the square channel. However, it is enhanced by 60% in comparison to placing ribs on the shorter side. The TPF remains constant at around 1 for the entire range of Reynolds numbers. The simulation results highlight that increased surface roughness can have a considerable influence on Nusselt number and overall TPF.
- 23 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (11)
Investigation of Gas Turbine Internal Cooling Using Supercritical CO2—Effect of Surface Roughness and Channel Aspect Ratio
Experimental and numerical investigation of internal cooling channels with rib turbulators is presented with sCO2 flow at pressure-20.7MPa and temperature up to 150°C. The effect of channel aspect ratio up to 2:1 on thermal-hydraulic performance is explored in additively manufactured rectangular and square channels, both with and without 60° ribs on the top and bottom sides. The Wilson-plot method is employed to measure channel averaged Nusselt number over a Reynolds number range up to 370,000. The friction factor and the overall thermal performance factor (TPF) are also reported. The computational fluid dynamics (CFD) simulation is performed for the rib-turbulated configurations reported in the experiments. The objective of the numerical study is to gain insight into the local heat transfer augmentation in the ribbed channels varying the aspect ratio, channel configuration, operating conditions and surface roughness. Surface roughness is simulated using sand grain roughness height (Ks) calculated from the experimental data, and a comparison is presented with varying surface roughness heights ranging between Ks = 0 - 40µm. Experimental results indicate that the heat transfer augmentation is negligible in the rectangular channels with ribs on the long side compared to the square channel. However, it is enhanced by 60% in comparison to placing ribs on the shorter side. The TPF remains constant at around 1 for the entire range of Reynolds numbers. The simulation results highlight that increased surface roughness can have a considerable influence on Nusselt number and overall TPF.
- Open Access
- 7 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Surface Roughness Effects on Heat Transfer in Additively Manufactured sCO2 Cycle Heat Exchangers
An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO2) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% less than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt numbr augmentation results. These results indicated a 10% improvement in heat duty for a heat exchangermore » constructed utilizing a tube with relative to a heat exchanger utilizing a smooth, conventional tube. « less
- 7 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessSurface Roughness Effects on Heat Transfer in Additively Manufactured sCO2 Cycle Heat Exchangers
An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO2) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% less than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt numbr augmentation results. These results indicated a 10% improvement in heat duty for a heat exchangermore » constructed utilizing a tube with relative to a heat exchanger utilizing a smooth, conventional tube. « less