Saif Taqy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saif Taqy has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Ariful Haque
Texas State University
6 shared publications - Adedayo Alaga
Electrical Engineering, Ingram School of Engineering, Texas State University
2 shared publications - Pallab Kumar Sarkar
Texas State University
2 shared publications Ravi Droopad
2 shared publications- Ravi Droopad
Department of Physics, Texas State University 2 , San Marcos, Texas 78666
2 shared publications - Abdul Hamid
School of Electrical, Computer, and Energy Engineering, Arizona State University 1 , Tempe, Arizona 85281
1 shared publication
Latest Publications
- Open Access
- 5 October 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (4)
p- and n-Type doping of AlN: Current challenges, emerging solutions, and device applications
Ultrawide bandgap aluminum nitride (AlN) has recently gained significant attention for high-power electronics and deep-ultraviolet (DUV) optoelectronics applications owing to its exceptionally large and direct bandgap, high breakdown field, and thermal and chemical stability. While these intrinsic properties promise substantial performance improvements over silicon (Si), silicon carbide (SiC), gallium nitride (GaN), gallium oxide (Ga2O3), and diamond devices, the core challenge lies in achieving a reliable n- and p-type doping due to deep impurity levels, carrier compensation, and native defect formation. This review is motivated by the urgent need to bridge fundamental doping science with device engineering to unlock the full potential of AlN in high-power devices and solar-blind DUV devices. We discuss a clear roadmap, beginning with a contextual overview of wide- and ultrawide bandgap semiconductors, highlighting why AlN stands out for high-power applications. The body of the review is structured into four core sections, starting with n-type doping techniques, covering silicon, oxygen, and germanium donors, compensation effects, and deep-level centers. Then, the challenges and progress in p-type doping are discussed, evaluating acceptor species (e.g., Mg, Be, C), co-doping schemes, and impurity-band engineering. Section IV focuses on different doping methods, including metal-organic chemical vapor deposition, molecular-beam epitaxy, metal-modulated epitaxy, ion implantation, and polarization doping, and their role in defect control and non-equilibrium activation. Section V presents how these material innovations translate to device prototypes, including Schottky diodes, polarization-doped field effect transistors, and deep-UV emitters, illustrating gradual improvements in the current technology. The review concludes with existing challenges and prospects of AlN, including vacancy-engineered contacts, scalable single-crystal substrates, co-doping strategies, and emerging device architectures that could yield reliable bipolar conductivity and practical AlN-based power electronics. By discussing critical components in theory, fundamental growth science, and device-level demonstrations of AlN, this review aims to serve as a comprehensive guide for researchers and engineers seeking to position AlN as a foundational material for next-generation power and optoelectronic systems.
- 5 October 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (4)
Open Accessp- and n-Type doping of AlN: Current challenges, emerging solutions, and device applications
Ultrawide bandgap aluminum nitride (AlN) has recently gained significant attention for high-power electronics and deep-ultraviolet (DUV) optoelectronics applications owing to its exceptionally large and direct bandgap, high breakdown field, and thermal and chemical stability. While these intrinsic properties promise substantial performance improvements over silicon (Si), silicon carbide (SiC), gallium nitride (GaN), gallium oxide (Ga2O3), and diamond devices, the core challenge lies in achieving a reliable n- and p-type doping due to deep impurity levels, carrier compensation, and native defect formation. This review is motivated by the urgent need to bridge fundamental doping science with device engineering to unlock the full potential of AlN in high-power devices and solar-blind DUV devices. We discuss a clear roadmap, beginning with a contextual overview of wide- and ultrawide bandgap semiconductors, highlighting why AlN stands out for high-power applications. The body of the review is structured into four core sections, starting with n-type doping techniques, covering silicon, oxygen, and germanium donors, compensation effects, and deep-level centers. Then, the challenges and progress in p-type doping are discussed, evaluating acceptor species (e.g., Mg, Be, C), co-doping schemes, and impurity-band engineering. Section IV focuses on different doping methods, including metal-organic chemical vapor deposition, molecular-beam epitaxy, metal-modulated epitaxy, ion implantation, and polarization doping, and their role in defect control and non-equilibrium activation. Section V presents how these material innovations translate to device prototypes, including Schottky diodes, polarization-doped field effect transistors, and deep-UV emitters, illustrating gradual improvements in the current technology. The review concludes with existing challenges and prospects of AlN, including vacancy-engineered contacts, scalable single-crystal substrates, co-doping strategies, and emerging device architectures that could yield reliable bipolar conductivity and practical AlN-based power electronics. By discussing critical components in theory, fundamental growth science, and device-level demonstrations of AlN, this review aims to serve as a comprehensive guide for researchers and engineers seeking to position AlN as a foundational material for next-generation power and optoelectronic systems.
- Open Access
- 10 July 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (27) , 275109
p -Type shallow doping and quality improvement of diamond via pulsed laser irradiation
Diamond, an ultrawide bandgap semiconductor with exceptional thermal, optical, and electrical properties, has attracted significant interest for next-generation electronic applications. However, its integration into micro and optoelectronic devices remains limited by doping challenges. Herein, pulsed laser irradiation (PLI) is employed as an approach for controlled boron doping in diamond. Boron incorporation is achieved via immersion in a boric acid precursor, followed by PLI at 0.34 J cm −2 to induce p-type conductivity in a patterned 5 × 5 mm 2 lab-grown HFCVD polycrystalline diamond (PCD). To mitigate laser-induced defects and suppress graphitization, a subsequent low-energy irradiation at 0.17 J cm −2 is applied. After an initial 500-pulse high-energy treatment, the quality factor (Q.F.) decreases from 94.01% to 93.70%, but recovers to 94.16% following 4000 pulses of low-energy exposure, yielding a net improvement of ∼0.5%. The treated sample exhibits a carrier concentration of +4.46 × 10 19 cm −3 and a hole mobility of 0.594 cm 2 V −1 s −1 . When applied to a commercial MSE PCD sample ( R a < 1 nm), this treatment maintains a Q.F. of 100% and reduces the transpolyacetylene (TPA) peak intensity by 43.08%. Electrical measurements reveal a carrier concentration of 1.166 × 10 19 cm −3 and a hole mobility of 7.09 cm 2 V −1 s −1 . These results demonstrate a practical route for achieving reliable p-type doping and improved structural quality in diamond for advanced electronic applications.
- 10 July 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (27) , 275109
Open Accessp -Type shallow doping and quality improvement of diamond via pulsed laser irradiation
Diamond, an ultrawide bandgap semiconductor with exceptional thermal, optical, and electrical properties, has attracted significant interest for next-generation electronic applications. However, its integration into micro and optoelectronic devices remains limited by doping challenges. Herein, pulsed laser irradiation (PLI) is employed as an approach for controlled boron doping in diamond. Boron incorporation is achieved via immersion in a boric acid precursor, followed by PLI at 0.34 J cm −2 to induce p-type conductivity in a patterned 5 × 5 mm 2 lab-grown HFCVD polycrystalline diamond (PCD). To mitigate laser-induced defects and suppress graphitization, a subsequent low-energy irradiation at 0.17 J cm −2 is applied. After an initial 500-pulse high-energy treatment, the quality factor (Q.F.) decreases from 94.01% to 93.70%, but recovers to 94.16% following 4000 pulses of low-energy exposure, yielding a net improvement of ∼0.5%. The treated sample exhibits a carrier concentration of +4.46 × 10 19 cm −3 and a hole mobility of 0.594 cm 2 V −1 s −1 . When applied to a commercial MSE PCD sample ( R a < 1 nm), this treatment maintains a Q.F. of 100% and reduces the transpolyacetylene (TPA) peak intensity by 43.08%. Electrical measurements reveal a carrier concentration of 1.166 × 10 19 cm −3 and a hole mobility of 7.09 cm 2 V −1 s −1 . These results demonstrate a practical route for achieving reliable p-type doping and improved structural quality in diamond for advanced electronic applications.
- Open Access
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Devices Magazine
- Vol. 4 (2) , 42-49
Aluminum Nitride Power Electronics Road Map: Materials, Devices, and Integration Path ways for Scalable Ultrawide-Bandgap Power Technologies
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Devices Magazine
- Vol. 4 (2) , 42-49
Open AccessAluminum Nitride Power Electronics Road Map: Materials, Devices, and Integration Path ways for Scalable Ultrawide-Bandgap Power Technologies
- Open Access
- 27 February 2026
- Published by Elsevier in SSRN Electronic Journal
Direct Fabrication of Diamond Films on β-Ga₂O₃ Using Q-carbon
Beta gallium oxide (β-Ga₂O₃) is a promising ultrawide-bandgap (UWBG) semiconductor for high-power electronic devices. However, its low thermal conductivity critically limits device performance. While diamond integration can address thermal management, it suffers from challenges such as stress, decomposition, and surface energy mismatch. To overcome these difficulties, pulsed laser annealing is used to form a thin quenched carbon (Q-carbon) layer on β-Ga₂O₃, promoting diamond growth while preventing cracking, delamination, and oxide-layer degradation. Simulation results show a melt regrowth velocity of 12.5 m/s that enables Q-carbon/nanodiamond composite formation on β-Ga₂O₃. Using Q-carbon as a seed layer resulted in the formation of a high-quality, uniform diamond film with minimal graphitic content and a sharp T2g peak at 1332.6 cm⁻¹ with an FWHM of 9.28 cm⁻¹. Furthermore, Q-carbon helps minimize the thermal mismatch between the diamond and β-Ga₂O₃ films, thereby preventing delamination of the diamond film during post-deposition cooling. Stress in diamond/Q-carbon/β-Ga₂O₃ was reduced by ~70% compared to untreated diamond/β-Ga₂O₃ and ~75% compared to diamond/c-Al₂O₃. Additionally, Q-carbon boosts the formation of well-faceted five-fold twinned diamond crystals and accelerates the growth of columnar structure diamond film. This study successfully addresses a persistent challenge in diamond nucleation and the fabrication of high-quality, large-area diamond growth on β-Ga₂O₃.
- 27 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDirect Fabrication of Diamond Films on β-Ga₂O₃ Using Q-carbon
Beta gallium oxide (β-Ga₂O₃) is a promising ultrawide-bandgap (UWBG) semiconductor for high-power electronic devices. However, its low thermal conductivity critically limits device performance. While diamond integration can address thermal management, it suffers from challenges such as stress, decomposition, and surface energy mismatch. To overcome these difficulties, pulsed laser annealing is used to form a thin quenched carbon (Q-carbon) layer on β-Ga₂O₃, promoting diamond growth while preventing cracking, delamination, and oxide-layer degradation. Simulation results show a melt regrowth velocity of 12.5 m/s that enables Q-carbon/nanodiamond composite formation on β-Ga₂O₃. Using Q-carbon as a seed layer resulted in the formation of a high-quality, uniform diamond film with minimal graphitic content and a sharp T2g peak at 1332.6 cm⁻¹ with an FWHM of 9.28 cm⁻¹. Furthermore, Q-carbon helps minimize the thermal mismatch between the diamond and β-Ga₂O₃ films, thereby preventing delamination of the diamond film during post-deposition cooling. Stress in diamond/Q-carbon/β-Ga₂O₃ was reduced by ~70% compared to untreated diamond/β-Ga₂O₃ and ~75% compared to diamond/c-Al₂O₃. Additionally, Q-carbon boosts the formation of well-faceted five-fold twinned diamond crystals and accelerates the growth of columnar structure diamond film. This study successfully addresses a persistent challenge in diamond nucleation and the fabrication of high-quality, large-area diamond growth on β-Ga₂O₃.
- 24 January 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 84
Structural and electronic properties of Q-carbon/AlN heterostructures
- 24 January 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 84
Structural and electronic properties of Q-carbon/AlN heterostructures
- 1 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (6)
Observation of low-resistance Al and Ni p-type ohmic contacts to dilute GeC and GeCSn alloys
Nickel and aluminum ohmic contacts were formed on p-doped GeC and GeCSn epitaxial films with ∼1%C. When a 40 nm p-GeC contact layer was added to p-Ge, annealed contact resistivity (Rc) dropped by 87% to 9.3 × 10−7 Ω cm2 for Al but increased by 32% to 2.9 × 10−5 Ω cm2 for Ni. On the other hand, thick films of GeCSn, which showed lower active doping, had contact resistivities of 4.4 × 10−6 Ω cm2 for Al and 1.4 × 10−5 Ω cm2 for Ni. In general, Al contacts were better than Ni, regardless of anneal, and were further improved by adding carbon. Annealing reduced Rc for both Ni and Al contacts to GeCSn by 4×, 2× for Al on GeC, and 5 orders of magnitude for Ni on GeC. It is speculated that C forms bonds with Ni that inhibit diffusion of Ni into the Ge, thus preventing the formation of low-resistance nickel germanide. Adding C, either as bulk GeCSn or as GeC contact layers, seems to significantly reduce the contact resistivity for Al contacts when compared to bulk Ge of comparable doping.
- 1 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (6)
Observation of low-resistance Al and Ni p-type ohmic contacts to dilute GeC and GeCSn alloys
Nickel and aluminum ohmic contacts were formed on p-doped GeC and GeCSn epitaxial films with ∼1%C. When a 40 nm p-GeC contact layer was added to p-Ge, annealed contact resistivity (Rc) dropped by 87% to 9.3 × 10−7 Ω cm2 for Al but increased by 32% to 2.9 × 10−5 Ω cm2 for Ni. On the other hand, thick films of GeCSn, which showed lower active doping, had contact resistivities of 4.4 × 10−6 Ω cm2 for Al and 1.4 × 10−5 Ω cm2 for Ni. In general, Al contacts were better than Ni, regardless of anneal, and were further improved by adding carbon. Annealing reduced Rc for both Ni and Al contacts to GeCSn by 4×, 2× for Al on GeC, and 5 orders of magnitude for Ni on GeC. It is speculated that C forms bonds with Ni that inhibit diffusion of Ni into the Ge, thus preventing the formation of low-resistance nickel germanide. Adding C, either as bulk GeCSn or as GeC contact layers, seems to significantly reduce the contact resistivity for Al contacts when compared to bulk Ge of comparable doping.
- 3 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (6) , 8305-8318
Highly Stable Electrochemical Supercapacitor Performance of Self-Assembled Ferromagnetic Q-Carbon
Novel phase Q-carbon thin films exhibit some intriguing features and have been explored for various potential applications. Herein, we report the growth of different Q-carbon structures (i.e., filaments, clusters, and microdots) by varying the laser energy density from 0.5 to 1.0 J/cm2 during pulsed laser annealing of amorphous diamond-like carbon films with different sp3-sp2 carbon compositions. These unique nano- and microstructures of Q-carbon demonstrate exceptionally stable electrochemical performance by cyclic voltammetry, galvanostatic charging-discharging, and electrochemical impedance spectroscopy for energy applications. The temperature-dependent magnetic studies (magnetization vs magnetic field and temperature) reveal the ferromagnetic nature of the Q-carbon microdots. The saturation magnetization and coercive field values decrease from 132 to 14 emu/cc and 155 to 92 Oe by increasing the temperature from 2 to 300 K, respectively. The electrochemical performances of Q-carbon filament, cluster, and microdot thin-film supercapacitors were investigated by two-electrode configurations, and the highest areal specific capacitance of ∼156 mF/cm2 was observed at a current density of 0.15 mA/cm2 in the Q-carbon microdot thin film. The Q-carbon microdot electrodes demonstrate an exceptional capacitance retention performance of ∼97.2% and Coulombic efficiency of ∼96.5% after 3000 cycles due to their expectational reversibility in the charging-discharging process. The kinetic feature of the ion diffusion associated with the charge storage property is also investigated, and small changes in equivalent series resistance of ∼9.5% and contact resistance of ∼9.1% confirm outstanding stability with active charge kinetics during the stability test. A high areal power density of ∼5.84 W/cm2 was obtained at an areal energy density of ∼0.058 W h/cm2 for the Q-carbon microdot structure. The theoretical quantum capacitance was obtained at ∼400 mF/cm2 by density functional theory calculation, which gives an idea about the overall capacitance value. The obtained areal specific capacitance, power density, and impressive long-term cyclic stability of Q-carbon thin-film microdot electrodes endorse substantial promise in high-performance supercapacitor applications.
- 3 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (6) , 8305-8318
Highly Stable Electrochemical Supercapacitor Performance of Self-Assembled Ferromagnetic Q-Carbon
Novel phase Q-carbon thin films exhibit some intriguing features and have been explored for various potential applications. Herein, we report the growth of different Q-carbon structures (i.e., filaments, clusters, and microdots) by varying the laser energy density from 0.5 to 1.0 J/cm2 during pulsed laser annealing of amorphous diamond-like carbon films with different sp3-sp2 carbon compositions. These unique nano- and microstructures of Q-carbon demonstrate exceptionally stable electrochemical performance by cyclic voltammetry, galvanostatic charging-discharging, and electrochemical impedance spectroscopy for energy applications. The temperature-dependent magnetic studies (magnetization vs magnetic field and temperature) reveal the ferromagnetic nature of the Q-carbon microdots. The saturation magnetization and coercive field values decrease from 132 to 14 emu/cc and 155 to 92 Oe by increasing the temperature from 2 to 300 K, respectively. The electrochemical performances of Q-carbon filament, cluster, and microdot thin-film supercapacitors were investigated by two-electrode configurations, and the highest areal specific capacitance of ∼156 mF/cm2 was observed at a current density of 0.15 mA/cm2 in the Q-carbon microdot thin film. The Q-carbon microdot electrodes demonstrate an exceptional capacitance retention performance of ∼97.2% and Coulombic efficiency of ∼96.5% after 3000 cycles due to their expectational reversibility in the charging-discharging process. The kinetic feature of the ion diffusion associated with the charge storage property is also investigated, and small changes in equivalent series resistance of ∼9.5% and contact resistance of ∼9.1% confirm outstanding stability with active charge kinetics during the stability test. A high areal power density of ∼5.84 W/cm2 was obtained at an areal energy density of ∼0.058 W h/cm2 for the Q-carbon microdot structure. The theoretical quantum capacitance was obtained at ∼400 mF/cm2 by density functional theory calculation, which gives an idea about the overall capacitance value. The obtained areal specific capacitance, power density, and impressive long-term cyclic stability of Q-carbon thin-film microdot electrodes endorse substantial promise in high-performance supercapacitor applications.