XJXiaoyu Ji

Xiaoyu Ji

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiaoyu Ji has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An integrated 3D field circuit coupled model for comparative study of quench behavior in NI REBCO coil under 3D and 2D axisymmetric framework

    by Hongzhuo Zeng, Yong Chen, Benzhe Zhou, Kangshuai Wang, Xiaoyu Ji, Fangliang Dong, Yiming Tang, Zili Zhang, Shunzhong Chen, Lei Wang, et al.

    Non-insulated (NI) high-temperature superconducting coils are widely used in various applications such as high-field and fusion magnets, rendering the precise evaluation of their thermal stability essential. Recently, 2D axisymmetric models are adopted by some researchers to simulate the minimum quench energy (MQE) and normal zone propagation velocity of circular NI coils in the event of whole-turn quench. However, the 2D axisymmetric model neglects the disparities of physical field variables in the circumferential direction, potentially resulting in inaccurate predictions. Therefore, this work develops a 3D quench model incorporating the screening currents of NI coils by coupling the 3D T – A formulation with the partial element equivalent circuit network. The entire quench model is integrated into a single COMSOL program, which avoids complex cross-platform interaction. Meanwhile, a 2D axisymmetric model is constructed based on existing voltage-driven T – A formulation. The above two models share identical parameters to facilitate a quantitative comparison of their simulation results for quench dynamics. To validate their effectiveness, the charging results of the two models are compared, showing good agreement. Moreover, due to the screening current effect, both models exhibit a transient increase in magnetic field during the initial stage of heating. However, even in the case of whole-turn quench, significant discrepancies remain in the quench propagation modes between the two models: the 2D axisymmetric model relies solely on thermal conduction and magnetic induction, failing to accurately characterize the current transfer mechanism observed in the 3D model. Further analysis indicates that the 2D axisymmetric model may overestimate the MQE under conditions of low coil contact resistivity. Nevertheless, the 2D axisymmetric model can be employed to rapidly estimate the approximate range of MQE in the 3D model. This paper provides valuable insights into the rational selection of different quench analysis models for NI coils.

  • Open Access

    Numerical investigation of thermal-fluid characteristics and helium bubble behavior in the 35.6 T all superconducting user magnet

    by Xiaoyu Ji, Benzhe Zhou, Yong Chen, Kangshuai Wang, Renjie Huang, Hongzhuo Zeng, Zili Zhang, Fangliang Dong, Jianhua Liu, Qiuliang Wang


  • Electromagnetic modeling of no-insulation REBCO coils based on T-A formulation: from 2D to 3D

    by Yong Chen, Qiuliang Wang, Benzhe Zhou, Shixian Liu, Fangliang Dong, Kangshuai Wang, Hongzhuo Zeng, Xiaoyu Ji, Lei Wang, Jianhua Liu

    The T-A formulation based on thin film approximation has been widely used in REBCO coated conductors and their various devices. Recently, its compatibility with electromagnetic modeling of no-insulation (NI) coils has attracted increasing attention. Although most electromagnetic simulations of NI coils have been addressed in 2D, the development of 3D models remains essential - for instance, to account for the circumferential non-uniformity of circular coils or to simulate non-circular configurations. In this study, by introducing the Coulomb gauge and a reduced nodal current conservation equation, we extend the electromagnetic modeling of NI REBCO coils based on T-A formulation from 2D axisymmetric scenarios to more general 3D helical frameworks, thereby highlight the electric potential characteristics. Furthermore, two 3D homogenized bulk models based on scaling equivalence of radial resistivity and concentricization of misaligned windings were proposed, and their applicability was also clarified. Comparative with the 2D circular NI coils shows that the 3D spiral model significantly improves the spatial resolution by incorporating actual current direction. The 3D homogenized bulk model achieves results consistent with the spiral model in terms of coil terminal voltage, charging delay, and power losses, while offering substantially enhanced computational efficiency. To demonstrate the practicality of the models, we further presented the simulation results for a 3D dual-wound NI coil with detailed spiral structure and a large-scale 3D homogenized racetrack NI coil with non-uniform radial resistivity. This work provides a new universal approach and tool for electromagnetic modeling of joints, irregular NI coils, and circular NI coils with circumferential non-uniformity.


  • Inversion of Equivalent Contact Resistivities of Parallel-Wound Metal-Insulation HTS Coil Based on Experimental Data and Multilevel Simulation

    by Hongzhuo Zeng, Qiuliang Wang, Yong Chen, Kangshuai Wang, Benzhe Zhou, Xiaoyu Ji, Fangliang Dong, Shunzhong Chen, Yinming Dai, Zili Zhang, et al.

    Equivalent contact resistivity is a key parameter that affects the dynamic process and overcurrent characteristic of the non-insulation (NI) high-temperature superconducting coil. Adding stainless steel material between turns of a parallel-wound NI coil results in the formation of various types of internal contact interfaces. Therefore, describing the shunt behavior of the coil, i.e., the parallel-wound metal-insulation (PWMI) coil, requires more than one equivalent contact resistivity, which makes it difficult to determine their specific values only through coil inductance and time constant. To handle this problem, we propose a method to acquire distinct equivalent contact resistivities of the PWMI coil. In this method, the equivalent contact resistivities are inverted based on the measured coil voltage or magnetic field. The bridge to connect the experimental data and equivalent contact resistivities is the streamlined field–circuit coupling model based on the T–A formulation, which can reflect the complex electromagnetic topology and the distribution of equivalent contact resistivities of the PWMI coil. After obtaining the measurement results, the least-squares method is used to optimize the equivalent contact resistivities until the simulation curve is sufficiently consistent with the experimental curve. In order to improve the efficiency of the optimization, we construct the lumped circuit model of the PWMI coil. Before the optimization process begins, the initial values of equivalent contact resistivities can be obtained based on this model, which can reduce the search scope of the optimization. The results of multiprocess testing indicate that using the equivalent contact resistivities obtained by the proposed method can effectively predict the transient behavior of the coil.


  • Numerical and experimental study of screening current mitigation under shaking field in no-insulation coils

    by Xiaoyu Ji, Benzhe Zhou, Kangshuai Wang, Tianyang Feng, Yong Chen, Hongzhuo Zeng, Qiuliang Wang, Jianhua Liu

    The screening current problem is one of the most critical challenges in high-temperature superconducting (HTS) coated conductors, severely degrading both the magnetic field magnitude and the stability of HTS inserts in high-field superconducting magnets. A promising strategy to mitigate screening current is the application of a shaking field perpendicular to the penetrating field. However, existing studies lack an effective computational model for the vortex shaking process and a comprehensive investigation into the unique characteristics of no-insulation (NI) coils under a shaking field. In this paper, a T-A formulation considering the coil thickness is used to simulate the electromagnetic behavior of NI coils during the shaking process. By combining simulations and experiments, the reduction of the screening current-induced field (SCIF) under varying coil parameters and operation conditions is investigated. The results indicate that the radial current has a dominant influence on the SCIF in NI coils with low contact resistivity. The rapid change in radial current induced by the shaking field leads to a sharp mitigation in the screening current within a short period, exhibiting a strong dependence on the shaking duration and coil’s contact resistivity. Moreover, this study demonstrates the effectiveness of the shaking field in accelerating radial current decline, and evaluates the additional AC losses induced by shaking field. These findings offer insights into the different mechanisms of the shaking field on SCIF reduction and radial current decline in NI coils, contributing to a better understanding of strategies for mitigating large screening current in REBCO magnets.


  • The Refined T-A Formulation for HTS No-Insulation Coils Considering Conductor Thickness

    by Xiaoyu Ji, Yong Chen, Benzhe Zhou, Qiuliang Wang, Jianhua Liu

    The T-A formulation of Maxwell’s equations is widely employed for modeling high temperature superconducting (HTS) coated conductors due to its high computational speed. However, when considering the thickness of the superconducting layer, the traditional T-A formulation still faces challenges in terms of low accuracy and poor convergence, particularly along the thickness direction, necessitating further refinement. In this article, a refined T-A formulation for no-insulation (NI) HTS coil considering the conductor thickness is introduced to address this limitation, and the corresponding homogeneous model is developed. The model’s accuracy is improved by applying Neumann boundary conditions and validated using both simulations and experimental results. Its advantages in calculating the distribution of screening current along the thickness direction are demonstrated in case studies, including the charging process and applying an axial shaking field to the NI coil. This refined method improves the accuracy and convergence of the T-A formulation, broadening its application to the transient analysis of HTS coil.


  • Analysis of Charging Strategy for a Large Conduction-Cooled HTS Magnet Under AC Conditions

    by Shixian Liu, Lei Wang, Luzhong Wang, Benzhe Zhou, Yong Chen, Xiaoyu Ji, Jinshui Sun, Yaohui Wang, Qiulang Wang

    A large-bore conduction-cooled high-temperature superconducting (HTS) magnet has been designed and fabricated at Institute of Electrical Engineering, Chinese Academy of Sciences (IEE, CAS). The magnet consists of ninety REBCO double-pancake (DP) coils with an inner diameter exceeding 450 mm, which is operated with alternating current (AC) to generate an ultra-low frequency alternating magnetic field. When the HTS magnet is charged up/down, it will be exposed to an alternating magnetic field and suffer large losses, which has a negative effect on the thermal stability of the magnet. In addition, the amplitude of the alternating magnetic field generated by the magnet is affected by the radial shunt of the turn-to-turn resistance. In this paper, the effects of charging speed and current amplitude on the losses and magnetic field of the HTS magnet under AC operating conditions were investigated. Firstly, an analytical model of the magnet was developed based on the equivalent circuit model and the finite element method. Subsequently, an optimized charging strategy was proposed to improve the alternating magnetic field to satisfy the application requirements better while ensuring the thermal stability of the magnet. Finally, the effectiveness of the strategy was verified by conduction-cooled experiments. The proposed charging strategy can effectively improve the alternating magnetic field while reducing the losses of the magnet. It provides guidance for the charging process of conduction-cooled HTS magnets under AC conditions in the future.