Davod Seifzadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Davod Seifzadeh has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Burak Dikici
Department of Mechanical Engineering, Atatürk University, Erzurum, Turkey
4 shared publications - Abolfazl Bezaatpour
University of Mohaghegh Ardabili
3 shared publications - Amir Nasser Shamkhali
Department of Chemistry, Faculty of Sciences, University of Mohaghegh Ardabili, 56199-11367 Ardabil, Iran
2 shared publications Roghaye Samadianfard
Corrosion and Industrial Electrochemistry Research Laboratory, University of Mohaghegh Ardabili, Ardabil, Iran
2 shared publicationsZ. Rajabalizadeh
Industrial Electrochemistry and Corrosion Laboratory, University of Mohaghegh Ardabili, Ardabil, Iran
2 shared publications- Zahra Rajabalizadeh
University of Mohaghegh Ardabili, Faculty of Science, Corrosion and Industrial Electrochemistry Research Laboratory, Ardabil-Iran
2 shared publications
Latest Publications
- Open Access
- 26 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (48) , 58490-58513
pH-Responsive Epoxy Coating Incorporating a Novel Schiff Base-Loaded UiO-66-NH2 with an Encapsulated Shell for Long-Term Steel Corrosion Protection
To address the low corrosion resistance of conventional epoxy coatings, a smart nanocomposite was designed by using UiO-66-NH2, a metal–organic framework (MOF), loaded with a new Schiff base as an inhibitor. The MOFs were encapsulated with a pH-responsive shell, allowing for the controlled release of the inhibitor. The crystallinity of UiO-66-NH2 remained preserved after encapsulation, and spherical particles were observed with an apparent size increase following encapsulation. The specific surface area of UiO-66-NH2 decreased from 860.18 to 131.06 m2 g–1 and pore volume from 1.9745 to 0.2871 cm3 g–1, indicating efficient pore occupation by the inhibitor. This change resulted in a loading efficiency of 30.5% and an encapsulation efficiency of 43.9%, which contribute to the enhanced corrosion resistance of the coating. The encapsulated UiO-66-NH2 exhibited smart behavior, releasing the highest amount of inhibitor at pH 12. The addition of UiO-66-NH2 and its encapsulated form eliminated micrometric defects in the coating, and the MOFs were uniformly distributed throughout the epoxy matrix. The incorporation of UiO-66-NH2 reduced the surface roughness of the epoxy coating from 3.909 to 3.260 μm, with a further decrease to 1.851 μm upon addition of its encapsulated form. Electrochemical impedance spectroscopy (EIS) studies in 0.2 M HCl revealed enhanced corrosion resistance after UiO-66-NH2 addition, mainly due to MOF-coating interactions, eliminating structural pores. After 6 weeks of immersion, the epoxy coating with encapsulated UiO-66-NH2 achieved a polarization resistance (R p) of 327.33 MΩ cm2, surpassing the neat epoxy coating by ∼41 times and the UiO-66-NH2-containing coating by ∼10 times. Potentiodynamic polarization (PDP) and postcorrosion morphology aligned well with EIS results. Density functional theory calculations confirmed the potential for chemical and physical adsorption of Schiff base molecules onto the steel. The coating designed in this study shows potential for protecting steel in industrial environments, including chemical processing plants and water treatment facilities.
- 26 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (48) , 58490-58513
Open AccesspH-Responsive Epoxy Coating Incorporating a Novel Schiff Base-Loaded UiO-66-NH2 with an Encapsulated Shell for Long-Term Steel Corrosion Protection
To address the low corrosion resistance of conventional epoxy coatings, a smart nanocomposite was designed by using UiO-66-NH2, a metal–organic framework (MOF), loaded with a new Schiff base as an inhibitor. The MOFs were encapsulated with a pH-responsive shell, allowing for the controlled release of the inhibitor. The crystallinity of UiO-66-NH2 remained preserved after encapsulation, and spherical particles were observed with an apparent size increase following encapsulation. The specific surface area of UiO-66-NH2 decreased from 860.18 to 131.06 m2 g–1 and pore volume from 1.9745 to 0.2871 cm3 g–1, indicating efficient pore occupation by the inhibitor. This change resulted in a loading efficiency of 30.5% and an encapsulation efficiency of 43.9%, which contribute to the enhanced corrosion resistance of the coating. The encapsulated UiO-66-NH2 exhibited smart behavior, releasing the highest amount of inhibitor at pH 12. The addition of UiO-66-NH2 and its encapsulated form eliminated micrometric defects in the coating, and the MOFs were uniformly distributed throughout the epoxy matrix. The incorporation of UiO-66-NH2 reduced the surface roughness of the epoxy coating from 3.909 to 3.260 μm, with a further decrease to 1.851 μm upon addition of its encapsulated form. Electrochemical impedance spectroscopy (EIS) studies in 0.2 M HCl revealed enhanced corrosion resistance after UiO-66-NH2 addition, mainly due to MOF-coating interactions, eliminating structural pores. After 6 weeks of immersion, the epoxy coating with encapsulated UiO-66-NH2 achieved a polarization resistance (R p) of 327.33 MΩ cm2, surpassing the neat epoxy coating by ∼41 times and the UiO-66-NH2-containing coating by ∼10 times. Potentiodynamic polarization (PDP) and postcorrosion morphology aligned well with EIS results. Density functional theory calculations confirmed the potential for chemical and physical adsorption of Schiff base molecules onto the steel. The coating designed in this study shows potential for protecting steel in industrial environments, including chemical processing plants and water treatment facilities.
- Open Access
- 13 May 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (33)
Sustainable Walnut Shell‐Filled Polylactic Acid–Hydroxyapatite Hybrid Coatings for Enhanced Corrosion Resistance and Bioactivity of Magnesium Biomaterials
Due to the high corrosion rate and limited biocompatibility of commonly used magnesium (Mg) and its alloys, current studies have focused on surface modification techniques. In this study, which is aimed at overcoming these obstacles in biomedical applications, hybrid coatings of PLA‐HA‐Walnut shell (Wshell) were successfully applied to Mg substrates. The presence of micropores on the surfaces of the hybrid coatings was detected using SEM surface morphology, and the elemental composition and structural characterization of the coatings were confirmed through analyses. With a higher Wshell fraction, the corrosion current density decreased significantly compared to uncoated Mg and PLA‐coated Mg, increasing the electrochemical corrosion resistance of Mg. The adhesion strength between the coatings and the Mg substrates increased to grade 3B with Wshell‐filled hybrid coatings. Moreover, the contact angle of PLA‐coated Mg decreased as the Wshell fraction increased, indicating enhanced surface wettability. Wshell hybrid coatings exhibit fibrous morphology and the formation of Ca‐ and P‐rich layers. These results, along with the filling of Wshell, suggest that PLA‐HA‐Wshell hybrid coatings could be a promising additive material for potential next‐generation low‐cost and sustainable biomedical coatings to enhance the corrosion resistance and bioactivity of Mg.
- 13 May 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (33)
Open AccessSustainable Walnut Shell‐Filled Polylactic Acid–Hydroxyapatite Hybrid Coatings for Enhanced Corrosion Resistance and Bioactivity of Magnesium Biomaterials
Due to the high corrosion rate and limited biocompatibility of commonly used magnesium (Mg) and its alloys, current studies have focused on surface modification techniques. In this study, which is aimed at overcoming these obstacles in biomedical applications, hybrid coatings of PLA‐HA‐Walnut shell (Wshell) were successfully applied to Mg substrates. The presence of micropores on the surfaces of the hybrid coatings was detected using SEM surface morphology, and the elemental composition and structural characterization of the coatings were confirmed through analyses. With a higher Wshell fraction, the corrosion current density decreased significantly compared to uncoated Mg and PLA‐coated Mg, increasing the electrochemical corrosion resistance of Mg. The adhesion strength between the coatings and the Mg substrates increased to grade 3B with Wshell‐filled hybrid coatings. Moreover, the contact angle of PLA‐coated Mg decreased as the Wshell fraction increased, indicating enhanced surface wettability. Wshell hybrid coatings exhibit fibrous morphology and the formation of Ca‐ and P‐rich layers. These results, along with the filling of Wshell, suggest that PLA‐HA‐Wshell hybrid coatings could be a promising additive material for potential next‐generation low‐cost and sustainable biomedical coatings to enhance the corrosion resistance and bioactivity of Mg.
- 18 April 2023
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 30 (6) , 1113-1127
Application of g-C3N4/sol—gel nanocomposite on AM60B magnesium alloy and investigation of its properties
- 18 April 2023
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 30 (6) , 1113-1127
Application of g-C3N4/sol—gel nanocomposite on AM60B magnesium alloy and investigation of its properties
- Open Access
Incorporation of Zinc Hydroxide Sulphate (ZHS) Nanoplates into Epoxy Resin to Improve Its Corrosion Protection
Zinc hydroxide sulphate (ZHS) nanoplates were synthesized and then characterized by various methods, including field-emission electron microscopy (FESEM), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron microscopy (XPS), thermal gravimetric analysis (TGA), and the Brunauer–Emmett–Teller (BET) theory. Then, the synthesized ZHS nanoplates were incorporated into the epoxy coating on a ST 37 steel alloy. No change in the morphology of the epoxy coating was observed after incorporating 1 wt. % ZHS nanoplates. Uniform distribution of the incorporated ZHS nanoplates inside the epoxy coating was confirmed by transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). Atomic force microscopy (AFM) images showed that the surface roughness (Sa) of the neat epoxy coating was about 1.1 µm, which was increased to about 2.1 µm by the incorporation of the ZHS nanoplates. The water contact angle on the coating was changed from 82.1 to 90.8° after incorporating the ZHS nanoplates, which may be attributed to the surface roughness. Electrochemical impedance spectroscopy (EIS) experiments showed that the polarization resistance of the epoxy coating in a 3.5 wt. % NaCl solution after 28 days of immersion was about 2.03 MΩ cm2, and increased to about 9.47 MΩ cm2 after adding the ZHS nanoplates. In addition, the capacitance of the ZHS-containing epoxy coating after 28 days of immersion in the corrosive solution was about 0.07 nsnΩ−1cm−2. The obtained value was more than four times lower than the value obtained for the neat epoxy coating (0.32 nsnΩ−1cm−2). The results of the EIS measurements indicated a significant increase in the corrosion resistance of the epoxy coating after the addition of the ZHS nanoplates. The improvement in the corrosion was explained by the filling of the possible defects and trapping of the aggressive agents by the incorporated ZHS nanoplates. FESEM and EDS analyses at the end of the immersion period confirmed the results of the corrosion tests.
Open AccessIncorporation of Zinc Hydroxide Sulphate (ZHS) Nanoplates into Epoxy Resin to Improve Its Corrosion Protection
Zinc hydroxide sulphate (ZHS) nanoplates were synthesized and then characterized by various methods, including field-emission electron microscopy (FESEM), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron microscopy (XPS), thermal gravimetric analysis (TGA), and the Brunauer–Emmett–Teller (BET) theory. Then, the synthesized ZHS nanoplates were incorporated into the epoxy coating on a ST 37 steel alloy. No change in the morphology of the epoxy coating was observed after incorporating 1 wt. % ZHS nanoplates. Uniform distribution of the incorporated ZHS nanoplates inside the epoxy coating was confirmed by transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). Atomic force microscopy (AFM) images showed that the surface roughness (Sa) of the neat epoxy coating was about 1.1 µm, which was increased to about 2.1 µm by the incorporation of the ZHS nanoplates. The water contact angle on the coating was changed from 82.1 to 90.8° after incorporating the ZHS nanoplates, which may be attributed to the surface roughness. Electrochemical impedance spectroscopy (EIS) experiments showed that the polarization resistance of the epoxy coating in a 3.5 wt. % NaCl solution after 28 days of immersion was about 2.03 MΩ cm2, and increased to about 9.47 MΩ cm2 after adding the ZHS nanoplates. In addition, the capacitance of the ZHS-containing epoxy coating after 28 days of immersion in the corrosive solution was about 0.07 nsnΩ−1cm−2. The obtained value was more than four times lower than the value obtained for the neat epoxy coating (0.32 nsnΩ−1cm−2). The results of the EIS measurements indicated a significant increase in the corrosion resistance of the epoxy coating after the addition of the ZHS nanoplates. The improvement in the corrosion was explained by the filling of the possible defects and trapping of the aggressive agents by the incorporated ZHS nanoplates. FESEM and EDS analyses at the end of the immersion period confirmed the results of the corrosion tests.
- 26 August 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (3) , 913-920
Electroless Nickel Plating on AM60B Magnesium Alloy via Ti-Zr/Sol-Gel Composite Layer as Pretreatment
The Ti-Zr and Ti-Zr/sol-gel were used as pretreatment layers before the electroless nickel coating on AM60B magnesium alloy. Scanning Electron Microscopy was employed to investigate the surface morphology of the pretreated layers and applied electroless coatings. Chemical analysis of the Ti-Zr layer, and nickel coatings was done using the Energy-Dispersive X-ray Spectroscopy. Moreover, the X-ray Diffraction and Atomic Force Microscopy methods were utilized to evaluate the microstructure and surface roughness of the electroless coatings, respectively. Electrochemical Impedance Spectroscopy was employed to study the corrosion behavior of Ni-P coatings. The results show that Ti-Zr layer has structural cracks, and the sol-gel film was covered all cracks entirely. The cauliflower-like electroless nickel coating was applied on both mentioned pretreated layers. The cross-sectional images revealed the higher thickness for the electroless coating on Ti-Zr/sol-gel layer, probably due to a large number of Ni nucleation centers. The EIS results demonstrate that the electroless coating on Ti-Zr/sol-gel has high corrosion protection and microhardness value.
- 26 August 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (3) , 913-920
Electroless Nickel Plating on AM60B Magnesium Alloy via Ti-Zr/Sol-Gel Composite Layer as Pretreatment
The Ti-Zr and Ti-Zr/sol-gel were used as pretreatment layers before the electroless nickel coating on AM60B magnesium alloy. Scanning Electron Microscopy was employed to investigate the surface morphology of the pretreated layers and applied electroless coatings. Chemical analysis of the Ti-Zr layer, and nickel coatings was done using the Energy-Dispersive X-ray Spectroscopy. Moreover, the X-ray Diffraction and Atomic Force Microscopy methods were utilized to evaluate the microstructure and surface roughness of the electroless coatings, respectively. Electrochemical Impedance Spectroscopy was employed to study the corrosion behavior of Ni-P coatings. The results show that Ti-Zr layer has structural cracks, and the sol-gel film was covered all cracks entirely. The cauliflower-like electroless nickel coating was applied on both mentioned pretreated layers. The cross-sectional images revealed the higher thickness for the electroless coating on Ti-Zr/sol-gel layer, probably due to a large number of Ni nucleation centers. The EIS results demonstrate that the electroless coating on Ti-Zr/sol-gel has high corrosion protection and microhardness value.
- 1 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (1) , 103345
Corrigendum to “Exceptional photocatalytic activity for g-C3N4 activated by H2O2 and integrated with Bi2S3 and Fe3O4 nanoparticles for removal of organic and inorganic pollutants”. [Adv. Powder Technol. 30(3) (2019) 524–537]
- 1 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (1) , 103345
Corrigendum to “Exceptional photocatalytic activity for g-C3N4 activated by H2O2 and integrated with Bi2S3 and Fe3O4 nanoparticles for removal of organic and inorganic pollutants”. [Adv. Powder Technol. 30(3) (2019) 524–537]
- 2 August 2021
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (9) , 1194-1205
Electroless Ni–B–MMT nanocomposite on magnesium alloy
Ni–B and Montmorillonite (MMT)-containing Ni–B deposits were electrolessly plated on AM60B magnesium alloy. The Ni–B coating showed cauliflower-like micromorphology, microcrystalline-amorphous microstructure, and thickness of about 15 μm, which was not influenced by the inclusion of MMT nanoparticles. The surface roughness of the Ni–B coating changed from about 376 to 328 nm after the inclusion of MMT. The boron content of the electroless deposit was mildly increased after MMT inclusion. Thermal shock and porosity examinations revealed suitable adhesion and pore-free structure of the coatings, respectively. Polarization resistance of the Ni–B deposit in 3.5 wt-% sodium chloride was increased about 1.5 times by MMT inclusion. The corrosion current of the substrate was remarkably diminished from 46.89 to 0.12 µA cm−2 by the Ni–B plating. Also, MMT incorporation causes to further decrement of the corrosion current to about 0.03 µA cm−2.
- 2 August 2021
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (9) , 1194-1205
Electroless Ni–B–MMT nanocomposite on magnesium alloy
Ni–B and Montmorillonite (MMT)-containing Ni–B deposits were electrolessly plated on AM60B magnesium alloy. The Ni–B coating showed cauliflower-like micromorphology, microcrystalline-amorphous microstructure, and thickness of about 15 μm, which was not influenced by the inclusion of MMT nanoparticles. The surface roughness of the Ni–B coating changed from about 376 to 328 nm after the inclusion of MMT. The boron content of the electroless deposit was mildly increased after MMT inclusion. Thermal shock and porosity examinations revealed suitable adhesion and pore-free structure of the coatings, respectively. Polarization resistance of the Ni–B deposit in 3.5 wt-% sodium chloride was increased about 1.5 times by MMT inclusion. The corrosion current of the substrate was remarkably diminished from 46.89 to 0.12 µA cm−2 by the Ni–B plating. Also, MMT incorporation causes to further decrement of the corrosion current to about 0.03 µA cm−2.
- 1 January 2020
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 56 (1) , 233-244
Synthesis and Characterization of a New N4S2 Schiff base and Investigation of its Adsorption and Corrosion Inhibition Effect by Experimental and Theoretical Methods
In this study, a new N4S2 Schiff base compound based on [2-({2-[(2-aminophenyl)thio]ethyl}thio)phenyl] amine and pyridine-2-carboxaldehyde was synthesized for the first time and its corrosion inhibition performance against mild steel corrosion in 1 M HCl was studied by several experimental and theoretical techniques. Potentiodynamic polarization examinations indicated that the synthesized N4S2 Schiff base performs as mixed-type inhibitor and its corrosion inhibition performance promoted at higher concentrations. Electrochemical Impedance Spectroscopy (EIS) examinations demonstrated that the polarization resistance of the mild steel increases by adding the synthesized compound while the capacitance values of the electrical double layer decreases indicating inhibitor adsorption at metal/electrolyte interface. The EIS experiments also revealed that the corrosion inhibition performance does not alter by increasing the temperature of the corrosive media from 30°C to 35°C but then slowly reduces with the subsequent increment in temperature since thermal agitation of the adsorbed inhibitor species accelerates. The inhibitor’s adsorption process is found to obey the Langmuir isotherm may be predominantly via chemisorption. However, possibility of the inhibitor physisorption was confirmed by calculation of potential of zero charge (EPZC) for the electrode surface in the blank and inhibitor-containing test electrolytes. Density Functional Theory (DFT) was also utilized to optimize the structure of the neutral N4S2 ligand and its protonated form along with their possible complex compounds with ferrous ions. Also, the relationship between structure of the N4S2 Schiff base and the corrosion inhibition performance was discussed by computing some quantum chemical parameters. Scanning Electron Microscopy (SEM) images approved the corrosion inhibition capacity of the Schiff base compound.
- 1 January 2020
- Published by Pleiades Publishing Ltd in Protection of Metals and Physical Chemistry of Surfaces
- Vol. 56 (1) , 233-244
Synthesis and Characterization of a New N4S2 Schiff base and Investigation of its Adsorption and Corrosion Inhibition Effect by Experimental and Theoretical Methods
In this study, a new N4S2 Schiff base compound based on [2-({2-[(2-aminophenyl)thio]ethyl}thio)phenyl] amine and pyridine-2-carboxaldehyde was synthesized for the first time and its corrosion inhibition performance against mild steel corrosion in 1 M HCl was studied by several experimental and theoretical techniques. Potentiodynamic polarization examinations indicated that the synthesized N4S2 Schiff base performs as mixed-type inhibitor and its corrosion inhibition performance promoted at higher concentrations. Electrochemical Impedance Spectroscopy (EIS) examinations demonstrated that the polarization resistance of the mild steel increases by adding the synthesized compound while the capacitance values of the electrical double layer decreases indicating inhibitor adsorption at metal/electrolyte interface. The EIS experiments also revealed that the corrosion inhibition performance does not alter by increasing the temperature of the corrosive media from 30°C to 35°C but then slowly reduces with the subsequent increment in temperature since thermal agitation of the adsorbed inhibitor species accelerates. The inhibitor’s adsorption process is found to obey the Langmuir isotherm may be predominantly via chemisorption. However, possibility of the inhibitor physisorption was confirmed by calculation of potential of zero charge (EPZC) for the electrode surface in the blank and inhibitor-containing test electrolytes. Density Functional Theory (DFT) was also utilized to optimize the structure of the neutral N4S2 ligand and its protonated form along with their possible complex compounds with ferrous ions. Also, the relationship between structure of the N4S2 Schiff base and the corrosion inhibition performance was discussed by computing some quantum chemical parameters. Scanning Electron Microscopy (SEM) images approved the corrosion inhibition capacity of the Schiff base compound.
- 11 March 2017
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 40 (2) , 407-415
Corrosion protection of AM60B magnesium alloy by application of electroless nickel coating via a new chrome-free pretreatment
- 11 March 2017
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 40 (2) , 407-415
Corrosion protection of AM60B magnesium alloy by application of electroless nickel coating via a new chrome-free pretreatment