Shili Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shili Jiang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Bohan Tang
University of Science and Technology of China, Hefei, China
8 shared publications - Donghui Jiang
High Magnetic Field Laboratory, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, China
8 shared publications - Guangli Kuang
Chinese Academy of Sciences
8 shared publications - Hui Yu
High Magnetic Field Laboratory, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, China
8 shared publications - Bowen Xie
University of Science and Technology of China, Hefei, China
7 shared publications - Shige Yang
University of Science and Technology of China, Hefei, China
6 shared publications
Latest Publications
- 26 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-9
Quench Propagation Characteristic of REBCO Stacks Under Conduction-Cooled Conditions
Due to the limited current-carrying capacity of a single high-temperature superconducting (HTS) tape, multiple tapes are often connected in parallel for high-field applications. Therefore, investigating the quench propagation characteristics of HTS stacks is crucial for ensuring the safe operation of HTS devices. Compared with liquid nitrogen immersion cooling, conduction-cooled quench tests are performed in a quasiadiabatic environment, minimizing environmental effects and allowing the results to more accurately reflect the intrinsic quench characteristics of the HTS stack. In this study, we investigate the quench propagation characteristics of REBCO stacks under conduction-cooled conditions. The stacks were fabricated using 4 mm-wide REBCO tapes, and a conduction-cooled quench test platform was built based on a GM cryocooler to perform measurements under near-adiabatic conditions. Potential taps were placed continuously along the length of the sample to monitor quench propagation, while thermocouples were attached to measure the temperature distribution. The minimum quench energy (MQE) and normal zone propagation velocity (NZPV) of the REBCO stacks were measured at ambient temperatures ranging from 60 K to 77 K. The experimental results are compared with those of a single tape sample. To verify the thermal behavior of the REBCO stack, a numerical analysis of the temperature trace was performed using the finite element method. The numerical simulation results were compared with the experimental data to verify the validity of the experimental data. The results indicate that differences in the coefficient of thermal expansion between the solder and the tapes during the cooling process led to a reduction in the critical current of the REBCO stack. As the temperature increases, both types of samples exhibit a decrease in MQE and a slowdown in NZPV. The heat absorption of the solder during quench increases the MQE of the stacked HTS tapes. Meanwhile, it also enhances the Joule heating power within the normal zone, and accelerates the NZPV.
- 26 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-9
Quench Propagation Characteristic of REBCO Stacks Under Conduction-Cooled Conditions
Due to the limited current-carrying capacity of a single high-temperature superconducting (HTS) tape, multiple tapes are often connected in parallel for high-field applications. Therefore, investigating the quench propagation characteristics of HTS stacks is crucial for ensuring the safe operation of HTS devices. Compared with liquid nitrogen immersion cooling, conduction-cooled quench tests are performed in a quasiadiabatic environment, minimizing environmental effects and allowing the results to more accurately reflect the intrinsic quench characteristics of the HTS stack. In this study, we investigate the quench propagation characteristics of REBCO stacks under conduction-cooled conditions. The stacks were fabricated using 4 mm-wide REBCO tapes, and a conduction-cooled quench test platform was built based on a GM cryocooler to perform measurements under near-adiabatic conditions. Potential taps were placed continuously along the length of the sample to monitor quench propagation, while thermocouples were attached to measure the temperature distribution. The minimum quench energy (MQE) and normal zone propagation velocity (NZPV) of the REBCO stacks were measured at ambient temperatures ranging from 60 K to 77 K. The experimental results are compared with those of a single tape sample. To verify the thermal behavior of the REBCO stack, a numerical analysis of the temperature trace was performed using the finite element method. The numerical simulation results were compared with the experimental data to verify the validity of the experimental data. The results indicate that differences in the coefficient of thermal expansion between the solder and the tapes during the cooling process led to a reduction in the critical current of the REBCO stack. As the temperature increases, both types of samples exhibit a decrease in MQE and a slowdown in NZPV. The heat absorption of the solder during quench increases the MQE of the stacked HTS tapes. Meanwhile, it also enhances the Joule heating power within the normal zone, and accelerates the NZPV.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Experimental Studies on Quench Detection of Stacked REBCO Tapes Using Fiber Bragg Gratings
The normal zone propagation velocity (NZPV) in high-temperature superconductors (HTS) is two to three orders of magnitude lower than that in low-temperature superconductors (LTS). This slow quench propagation poses a critical challenge for quench detection in HTS applications. Fiber Bragg Grating (FBG) sensors have demonstrated potential as cryogenic sensors for quench detection in HTS applications. But determining an appropriate threshold value for the central wavelength shift (Δλ) in quench detection remains a question to be addressed. In this paper, both single superconducting tapes and stacked tapes, which serve as the fundamental building blocks of HTS cables, are investigated. The time delay of the FBG sensor is demonstrated to be shorter than that of voltage taps when a hotspot occurs at the grating location. The Δλ corresponding to quench temperature—the threshold examined in this study—decreases as the distance from the hotspot increases. The FBG can effectively respond to a quench event more quickly than voltage, when the distance from the hot spot is less than 10 mm.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Experimental Studies on Quench Detection of Stacked REBCO Tapes Using Fiber Bragg Gratings
The normal zone propagation velocity (NZPV) in high-temperature superconductors (HTS) is two to three orders of magnitude lower than that in low-temperature superconductors (LTS). This slow quench propagation poses a critical challenge for quench detection in HTS applications. Fiber Bragg Grating (FBG) sensors have demonstrated potential as cryogenic sensors for quench detection in HTS applications. But determining an appropriate threshold value for the central wavelength shift (Δλ) in quench detection remains a question to be addressed. In this paper, both single superconducting tapes and stacked tapes, which serve as the fundamental building blocks of HTS cables, are investigated. The time delay of the FBG sensor is demonstrated to be shorter than that of voltage taps when a hotspot occurs at the grating location. The Δλ corresponding to quench temperature—the threshold examined in this study—decreases as the distance from the hotspot increases. The FBG can effectively respond to a quench event more quickly than voltage, when the distance from the hot spot is less than 10 mm.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Impact of Different Nonlinear E-J Relations on the Solvability and Convergence of High-Temperature Superconductor Quench Simulations
The current sharing process and increase in the electric field are closely related to the E-J relation during the quench of high-temperature superconductor (HTS). E-J power-law relation of the type E = Ec(J/Jc)n is widely used in modeling the dynamics of HTS, with Ec typically defined as 10−4 V/m, corresponding with the electric field when the current density J equals the critical current density Jc. This value is much lower than the electric field within a 40-μm-thick copper stabilizer carrying a current greater than 10 A, as well as the average electric field observed in the quenching zone during experiments. It means the current density is far greater than the critical current density when quench happens. The high ratio of J/Jc along with the E-J power-law relation brings difficulty in the convergence of the numerical model. This paper presented the comparison of the numerical simulation of the quench propagation problem in a single tape model with three nonlinearity E-J relations. The comparison reveals that one of these relations, in particular, significantly enhances the solvability and convergence of the quench model while resulting in smaller relative errors.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Impact of Different Nonlinear E-J Relations on the Solvability and Convergence of High-Temperature Superconductor Quench Simulations
The current sharing process and increase in the electric field are closely related to the E-J relation during the quench of high-temperature superconductor (HTS). E-J power-law relation of the type E = Ec(J/Jc)n is widely used in modeling the dynamics of HTS, with Ec typically defined as 10−4 V/m, corresponding with the electric field when the current density J equals the critical current density Jc. This value is much lower than the electric field within a 40-μm-thick copper stabilizer carrying a current greater than 10 A, as well as the average electric field observed in the quenching zone during experiments. It means the current density is far greater than the critical current density when quench happens. The high ratio of J/Jc along with the E-J power-law relation brings difficulty in the convergence of the numerical model. This paper presented the comparison of the numerical simulation of the quench propagation problem in a single tape model with three nonlinearity E-J relations. The comparison reveals that one of these relations, in particular, significantly enhances the solvability and convergence of the quench model while resulting in smaller relative errors.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (9) , 1-10
Modeling of the Stacked High-Temperature Superconducting Cable-in-Conduit Conductor for High-Field Magnet Applications
High-temperature superconducting (HTS) materials hold great promise for advancing large-scale high-field magnets. This paper presents a comprehensive study on the design, fabrication, and performance evaluation of stacked HTS cable-in-conduit conductors (CICCs) for a prospective 55 T hybrid magnet, conducted through finite element modeling. The CICC configuration features a central copper core surrounded by straight-slotted channels filled with solder and rare-earth barium copper oxide (REBCO) tapes, encased in copper and stainless steel (SS) jackets. Key aspects investigated include critical current characteristics, stress-strain, bending behaviors, and thermal performance of the stacked HTS CICCs. Critical current evaluation and tensile/compressive stress at 77 K and 4.2 K self-fields, along with analysis of responses to varying magnetic induction intensities and orientations, is conducted. Strain distribution in the conductor at different bending radii and temperature distribution along the conductor under various cooling processing are analyzed. The study involves numerical modeling of conductor behavior under diverse magnetic fields, mechanical loading conditions, and thermal environments. Additionally, critical current analysis, strain distribution assessment, and cooling performance evaluation offer valuable insights into the operational capabilities of the conductor. The model evaluates electromagnetic, mechanical, and low-temperature properties of the stacked HTS CICC, suggesting its suitability for HTS coils within large-scale magnets following optimization. These findings offer insights crucial for designing and optimizing CICCs for high-field magnet applications.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (9) , 1-10
Modeling of the Stacked High-Temperature Superconducting Cable-in-Conduit Conductor for High-Field Magnet Applications
High-temperature superconducting (HTS) materials hold great promise for advancing large-scale high-field magnets. This paper presents a comprehensive study on the design, fabrication, and performance evaluation of stacked HTS cable-in-conduit conductors (CICCs) for a prospective 55 T hybrid magnet, conducted through finite element modeling. The CICC configuration features a central copper core surrounded by straight-slotted channels filled with solder and rare-earth barium copper oxide (REBCO) tapes, encased in copper and stainless steel (SS) jackets. Key aspects investigated include critical current characteristics, stress-strain, bending behaviors, and thermal performance of the stacked HTS CICCs. Critical current evaluation and tensile/compressive stress at 77 K and 4.2 K self-fields, along with analysis of responses to varying magnetic induction intensities and orientations, is conducted. Strain distribution in the conductor at different bending radii and temperature distribution along the conductor under various cooling processing are analyzed. The study involves numerical modeling of conductor behavior under diverse magnetic fields, mechanical loading conditions, and thermal environments. Additionally, critical current analysis, strain distribution assessment, and cooling performance evaluation offer valuable insights into the operational capabilities of the conductor. The model evaluates electromagnetic, mechanical, and low-temperature properties of the stacked HTS CICC, suggesting its suitability for HTS coils within large-scale magnets following optimization. These findings offer insights crucial for designing and optimizing CICCs for high-field magnet applications.
- Open Access
- 2 August 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (9) , 095023
Thermal degradation analysis and optimization of controlled heat treatment for stacked high temperature superconducting tapes
High temperature superconducting (HTS) tapes have crucial applications for generating high magnetic fields with minimal power input. Given a single tape has a limited current-carrying capacity, stacked tapes are common, fabricated through methods like solder soldering or epoxy impregnation requiring heat treatment. In this work, we have investigated the efficient region for vacuum heat treatment applicable of commercial HTS tapes, analysed the thermal degradation principles and accordingly proposed a controlled heat treatment process for stacked HTS tapes to achieve more precise regulation of the critical current ( I c ). This heat treatment process was explored using a specialized multi-temperature zone vacuum system. Critical parameters in this process include heat treatment temperature, duration and pressure on the tape. A series of experiments were conducted at 77 K in a self-field to investigate how these parameters affect the superconductivity performance of stacked HTS tapes. Based on the experimental results, an optimal heat treatment process has been proposed. Under the current process, with the heat treatment temperature set at 200 °C, duration at 20 min, and pressure on the tape at 12 MPa, the samples exhibit favourable properties characterized by a smooth and neat appearance without defects such as pinholes or false soldering, and the superconductivity performance can be consistently maintained at more than 97%. The obtained measurements were compared with simulated results, demonstrating an error margin within 0.5%. Moreover, precise control of I c is achieved, tailored to tape and stacking specifications, allowing manageable degradation as required. This heat treatment process for stacked HTS tapes holds significant importance, especially in the context of designing cable-in-conduit conductors fabricated with stacked HTS tapes. It serves as a valuable reference for further advancements in this field.
- 2 August 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (9) , 095023
Open AccessThermal degradation analysis and optimization of controlled heat treatment for stacked high temperature superconducting tapes
High temperature superconducting (HTS) tapes have crucial applications for generating high magnetic fields with minimal power input. Given a single tape has a limited current-carrying capacity, stacked tapes are common, fabricated through methods like solder soldering or epoxy impregnation requiring heat treatment. In this work, we have investigated the efficient region for vacuum heat treatment applicable of commercial HTS tapes, analysed the thermal degradation principles and accordingly proposed a controlled heat treatment process for stacked HTS tapes to achieve more precise regulation of the critical current ( I c ). This heat treatment process was explored using a specialized multi-temperature zone vacuum system. Critical parameters in this process include heat treatment temperature, duration and pressure on the tape. A series of experiments were conducted at 77 K in a self-field to investigate how these parameters affect the superconductivity performance of stacked HTS tapes. Based on the experimental results, an optimal heat treatment process has been proposed. Under the current process, with the heat treatment temperature set at 200 °C, duration at 20 min, and pressure on the tape at 12 MPa, the samples exhibit favourable properties characterized by a smooth and neat appearance without defects such as pinholes or false soldering, and the superconductivity performance can be consistently maintained at more than 97%. The obtained measurements were compared with simulated results, demonstrating an error margin within 0.5%. Moreover, precise control of I c is achieved, tailored to tape and stacking specifications, allowing manageable degradation as required. This heat treatment process for stacked HTS tapes holds significant importance, especially in the context of designing cable-in-conduit conductors fabricated with stacked HTS tapes. It serves as a valuable reference for further advancements in this field.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-6
Research on the Radial Crimping Process for Stacked High-Temperature Superconducting Cable-in-Conduit Conductor
The radial crimping process is a crucial step in fabricating stacked high-temperature superconducting (HTS) cable-in-conduit conductor (CICC) made with rare earth barium copper oxide (REBCO) HTS tapes for the application of large-scale HTS magnets at low temperatures. This paper presents theoretical research on the forming principle and correlated law of the radial crimping process for stacked HTS CICC. Firstly, a finite element model is developed to simulate the forming process of the conductor under the conditions of the radial crimping process steps. Subsequently, the changes in the wall thickness of the jacket, the stress-strain distribution of the conductor, and the deformation characteristics of the stacked tapes during the forming process are analyzed. Finally, by comparing the calculated results with the experimental ones, the effects of different crimping steps on the forming quality of the conductor are studied. This research can provide significant references for optimizing the manufacturing process of stacked HTS CICCs and improving the overall performance of the conductor.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-6
Research on the Radial Crimping Process for Stacked High-Temperature Superconducting Cable-in-Conduit Conductor
The radial crimping process is a crucial step in fabricating stacked high-temperature superconducting (HTS) cable-in-conduit conductor (CICC) made with rare earth barium copper oxide (REBCO) HTS tapes for the application of large-scale HTS magnets at low temperatures. This paper presents theoretical research on the forming principle and correlated law of the radial crimping process for stacked HTS CICC. Firstly, a finite element model is developed to simulate the forming process of the conductor under the conditions of the radial crimping process steps. Subsequently, the changes in the wall thickness of the jacket, the stress-strain distribution of the conductor, and the deformation characteristics of the stacked tapes during the forming process are analyzed. Finally, by comparing the calculated results with the experimental ones, the effects of different crimping steps on the forming quality of the conductor are studied. This research can provide significant references for optimizing the manufacturing process of stacked HTS CICCs and improving the overall performance of the conductor.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
A Numerical Method Coupling the T-A Formulation for Dynamic Resistance Computation in HTS Coated Conductors
High temperature superconducting coated conductor carrying direct current (dc) presents a dynamic resistance under an external perpendicular alternating current (ac) magnetic field, which is far more than the E-J relation measured in a steady field and varies with the frequency and amplitude of the external magnetic field. This study proposes a numerical method coupling T-A formulation and element equivalent shunt circuit equation. Numerical results of dynamic resistance have been compared to previous experiments, T-A formulation using power law E-J relation and an analytical equation. The comparison shows a strong performance of our method across a wide range of frequencies and field magnitudes, including both high and low-frequency regimes. Additionally, it reveals the reason for the differences in experimental results and the other two methods.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
A Numerical Method Coupling the T-A Formulation for Dynamic Resistance Computation in HTS Coated Conductors
High temperature superconducting coated conductor carrying direct current (dc) presents a dynamic resistance under an external perpendicular alternating current (ac) magnetic field, which is far more than the E-J relation measured in a steady field and varies with the frequency and amplitude of the external magnetic field. This study proposes a numerical method coupling T-A formulation and element equivalent shunt circuit equation. Numerical results of dynamic resistance have been compared to previous experiments, T-A formulation using power law E-J relation and an analytical equation. The comparison shows a strong performance of our method across a wide range of frequencies and field magnitudes, including both high and low-frequency regimes. Additionally, it reveals the reason for the differences in experimental results and the other two methods.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Experimental Studies on Quench Behavior Measurements of HTS Tapes With Various Heater Configurations
In experimental studies of HTS quench behaviors, different experimental protocols, especially heater configurations, including heater pulse duration and magnitudes, can lead to inconsistent measured results. In this work, mainly based on experimental measurements, the quench characteristics of REBCO samples, including minimum quench energy (MQE) and normal zone propagation velocities (NZPV), are investigated with various heater configurations. The relations between the measured quench characteristics and the heater configurations demonstrated that the measured MQE increased with the increasing heater pulse duration employed in the quench experiments, and the heater pulse duration had better be smaller than the diffusion time constant over minimum propagation zone; and the heater pulses adopted in the quench measurements for the stacks can be longer than that for the single tape.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Experimental Studies on Quench Behavior Measurements of HTS Tapes With Various Heater Configurations
In experimental studies of HTS quench behaviors, different experimental protocols, especially heater configurations, including heater pulse duration and magnitudes, can lead to inconsistent measured results. In this work, mainly based on experimental measurements, the quench characteristics of REBCO samples, including minimum quench energy (MQE) and normal zone propagation velocities (NZPV), are investigated with various heater configurations. The relations between the measured quench characteristics and the heater configurations demonstrated that the measured MQE increased with the increasing heater pulse duration employed in the quench experiments, and the heater pulse duration had better be smaller than the diffusion time constant over minimum propagation zone; and the heater pulses adopted in the quench measurements for the stacks can be longer than that for the single tape.