Guangli Kuang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guangli Kuang has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Donghui Jiang
High Magnetic Field Laboratory, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, China
15 shared publications - Wenge Chen
High Magnetic Field Laboratory, Chinese Academy of Sciences, Hefei, China
11 shared publications - Bohan Tang
University of Science and Technology of China, Hefei, China
10 shared publications - Hui Yu
High Magnetic Field Laboratory, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, China
10 shared publications - Bowen Xie
University of Science and Technology of China, Hefei, China
9 shared publications Wenge Chen
High Magnetic Field Laboratory, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, China
9 shared publications
Latest Publications
- 1 January 2027
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 37 (1) , 4700307
Research of Normal Zone Propagation Velocity Behaviors of REBCO Tape After Heat Treatment
- 1 January 2027
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 37 (1) , 4700307
Research of Normal Zone Propagation Velocity Behaviors of REBCO Tape After Heat Treatment
- 26 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-9
Quench Propagation Characteristic of REBCO Stacks Under Conduction-Cooled Conditions
Due to the limited current-carrying capacity of a single high-temperature superconducting (HTS) tape, multiple tapes are often connected in parallel for high-field applications. Therefore, investigating the quench propagation characteristics of HTS stacks is crucial for ensuring the safe operation of HTS devices. Compared with liquid nitrogen immersion cooling, conduction-cooled quench tests are performed in a quasiadiabatic environment, minimizing environmental effects and allowing the results to more accurately reflect the intrinsic quench characteristics of the HTS stack. In this study, we investigate the quench propagation characteristics of REBCO stacks under conduction-cooled conditions. The stacks were fabricated using 4 mm-wide REBCO tapes, and a conduction-cooled quench test platform was built based on a GM cryocooler to perform measurements under near-adiabatic conditions. Potential taps were placed continuously along the length of the sample to monitor quench propagation, while thermocouples were attached to measure the temperature distribution. The minimum quench energy (MQE) and normal zone propagation velocity (NZPV) of the REBCO stacks were measured at ambient temperatures ranging from 60 K to 77 K. The experimental results are compared with those of a single tape sample. To verify the thermal behavior of the REBCO stack, a numerical analysis of the temperature trace was performed using the finite element method. The numerical simulation results were compared with the experimental data to verify the validity of the experimental data. The results indicate that differences in the coefficient of thermal expansion between the solder and the tapes during the cooling process led to a reduction in the critical current of the REBCO stack. As the temperature increases, both types of samples exhibit a decrease in MQE and a slowdown in NZPV. The heat absorption of the solder during quench increases the MQE of the stacked HTS tapes. Meanwhile, it also enhances the Joule heating power within the normal zone, and accelerates the NZPV.
- 26 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-9
Quench Propagation Characteristic of REBCO Stacks Under Conduction-Cooled Conditions
Due to the limited current-carrying capacity of a single high-temperature superconducting (HTS) tape, multiple tapes are often connected in parallel for high-field applications. Therefore, investigating the quench propagation characteristics of HTS stacks is crucial for ensuring the safe operation of HTS devices. Compared with liquid nitrogen immersion cooling, conduction-cooled quench tests are performed in a quasiadiabatic environment, minimizing environmental effects and allowing the results to more accurately reflect the intrinsic quench characteristics of the HTS stack. In this study, we investigate the quench propagation characteristics of REBCO stacks under conduction-cooled conditions. The stacks were fabricated using 4 mm-wide REBCO tapes, and a conduction-cooled quench test platform was built based on a GM cryocooler to perform measurements under near-adiabatic conditions. Potential taps were placed continuously along the length of the sample to monitor quench propagation, while thermocouples were attached to measure the temperature distribution. The minimum quench energy (MQE) and normal zone propagation velocity (NZPV) of the REBCO stacks were measured at ambient temperatures ranging from 60 K to 77 K. The experimental results are compared with those of a single tape sample. To verify the thermal behavior of the REBCO stack, a numerical analysis of the temperature trace was performed using the finite element method. The numerical simulation results were compared with the experimental data to verify the validity of the experimental data. The results indicate that differences in the coefficient of thermal expansion between the solder and the tapes during the cooling process led to a reduction in the critical current of the REBCO stack. As the temperature increases, both types of samples exhibit a decrease in MQE and a slowdown in NZPV. The heat absorption of the solder during quench increases the MQE of the stacked HTS tapes. Meanwhile, it also enhances the Joule heating power within the normal zone, and accelerates the NZPV.
- 23 February 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (8) , 085202
High-thrust electroaerodynamic propulsion enabled by multi-pair and multi-stage arrays
Electroaerodynamic (EAD) thrusters produce thrust via corona discharge in asymmetric capacitors, where ions emitted from the emitter electrode are accelerated toward the collector electrode, transferring momentum to neutral molecules and generating an ionic wind. Their lack of moving parts, low noise, and absence of combustion emissions make them attractive for unconventional propulsion. However, current EAD prototypes typically deliver thrust only at the milli-Newton level, and achieving Newton-level output is a critical prerequisite for practical application. To address this challenge, this study employs numerical and experimental methods to investigate parallel (multi-pair) and series (multi-stage) electrode configurations with different geometries and circuit arrangements, aiming to realize high-thrust EAD thrusters. For multi-pair thrusters, inter-pair interactions are shown to redistribute charges and reduce thrust, depending on the emitter–collector gap, inter-pair spacing, and applied voltage. For multi-stage thrusters, alternating-polarity circuits outperform same-potential ones, and the inter-stage spacing critically determines whether the ionic wind from the first stage enhances or weakens the next stage. Finally, a small-scale EAD prototype with five pairs and two stages (0.55 m × 0.1 m × 0.1 m) was constructed, producing 0.45 N of thrust with a thrust density of up to 80 N m −3 , enabling analysis of multi-pair, multi-stage interactions. A subsequent large-scale prototype with 20 pairs and 10 stages (∼1 m × 1 m × 1 m) produced more than 20 N of thrust, demonstrating the feasibility of high-thrust EAD propulsion.
- 23 February 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (8) , 085202
High-thrust electroaerodynamic propulsion enabled by multi-pair and multi-stage arrays
Electroaerodynamic (EAD) thrusters produce thrust via corona discharge in asymmetric capacitors, where ions emitted from the emitter electrode are accelerated toward the collector electrode, transferring momentum to neutral molecules and generating an ionic wind. Their lack of moving parts, low noise, and absence of combustion emissions make them attractive for unconventional propulsion. However, current EAD prototypes typically deliver thrust only at the milli-Newton level, and achieving Newton-level output is a critical prerequisite for practical application. To address this challenge, this study employs numerical and experimental methods to investigate parallel (multi-pair) and series (multi-stage) electrode configurations with different geometries and circuit arrangements, aiming to realize high-thrust EAD thrusters. For multi-pair thrusters, inter-pair interactions are shown to redistribute charges and reduce thrust, depending on the emitter–collector gap, inter-pair spacing, and applied voltage. For multi-stage thrusters, alternating-polarity circuits outperform same-potential ones, and the inter-stage spacing critically determines whether the ionic wind from the first stage enhances or weakens the next stage. Finally, a small-scale EAD prototype with five pairs and two stages (0.55 m × 0.1 m × 0.1 m) was constructed, producing 0.45 N of thrust with a thrust density of up to 80 N m −3 , enabling analysis of multi-pair, multi-stage interactions. A subsequent large-scale prototype with 20 pairs and 10 stages (∼1 m × 1 m × 1 m) produced more than 20 N of thrust, demonstrating the feasibility of high-thrust EAD propulsion.
- 4 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (1) , 1-11
Investigation of Magnetic Screening Performance Enhancement Using Various Superconductors and Ferromagnets
This work investigates a hybrid passive screen integrating superconductors and ferromagnets. The screening structure consists of multiple superconducting bulks, stacked closed-loop eye-shaped coated conductors, and a ferromagnetic (FM) sheet. The stacked coated conductors are concentrically arranged around the bulks, with the FM sheet positioned on the upper surface of the bulks. The screening effects are examined through experimental measurements and finite element calculations. We investigate superconducting screens of various structures, firstly, revealing that the combination of superconductors provides superior screening performance compared to using bulks alone. Furthermore, partial reversal of the tapes’ directions was applied to optimize geometrical asymmetry. The superconducting-FM hybrid screen was then tested, achieving a substantial reduction in residual magnetic flux density (up to 38%) in the gap region while simultaneously improving field uniformity. Importantly, the established numerical model enables further exploration and optimization of the screen, allowing for expanded screening volume and operation at higher magnetic field levels.
- 4 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (1) , 1-11
Investigation of Magnetic Screening Performance Enhancement Using Various Superconductors and Ferromagnets
This work investigates a hybrid passive screen integrating superconductors and ferromagnets. The screening structure consists of multiple superconducting bulks, stacked closed-loop eye-shaped coated conductors, and a ferromagnetic (FM) sheet. The stacked coated conductors are concentrically arranged around the bulks, with the FM sheet positioned on the upper surface of the bulks. The screening effects are examined through experimental measurements and finite element calculations. We investigate superconducting screens of various structures, firstly, revealing that the combination of superconductors provides superior screening performance compared to using bulks alone. Furthermore, partial reversal of the tapes’ directions was applied to optimize geometrical asymmetry. The superconducting-FM hybrid screen was then tested, achieving a substantial reduction in residual magnetic flux density (up to 38%) in the gap region while simultaneously improving field uniformity. Importantly, the established numerical model enables further exploration and optimization of the screen, allowing for expanded screening volume and operation at higher magnetic field levels.
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Design of Room Temperature Shimming System for 400 MHz NMR
The room-temperature shimming coils are installed within the bore of the superconducting magnet. By applying different excitation currents to each set of coils, different compensating magnetic fields are generated to modify specific components of the main magnetic field, thereby improving its uniformity. For a nuclear magnetic resonance spectrometer operating at 400 MHz, the initial magnetic field uniformity must be better than 1 ppm in a 10 mm DSV (Diameter Spherical Volume). After active shimming using the room-temperature shimming coils, the uniformity should be improved to within 10 ppb in the same DSV. This paper focuses on the design of a room-temperature shimming system for a 400 MHz NMR spectrometer. The coil design for each shimming order is based on spherical harmonic function analysis and the target field method, implemented via the finite difference stream function approach. Additionally, the measurement system and power supply system for the shimming coils are described.
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Design of Room Temperature Shimming System for 400 MHz NMR
The room-temperature shimming coils are installed within the bore of the superconducting magnet. By applying different excitation currents to each set of coils, different compensating magnetic fields are generated to modify specific components of the main magnetic field, thereby improving its uniformity. For a nuclear magnetic resonance spectrometer operating at 400 MHz, the initial magnetic field uniformity must be better than 1 ppm in a 10 mm DSV (Diameter Spherical Volume). After active shimming using the room-temperature shimming coils, the uniformity should be improved to within 10 ppb in the same DSV. This paper focuses on the design of a room-temperature shimming system for a 400 MHz NMR spectrometer. The coil design for each shimming order is based on spherical harmonic function analysis and the target field method, implemented via the finite difference stream function approach. Additionally, the measurement system and power supply system for the shimming coils are described.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Experimental Studies on Quench Detection of Stacked REBCO Tapes Using Fiber Bragg Gratings
The normal zone propagation velocity (NZPV) in high-temperature superconductors (HTS) is two to three orders of magnitude lower than that in low-temperature superconductors (LTS). This slow quench propagation poses a critical challenge for quench detection in HTS applications. Fiber Bragg Grating (FBG) sensors have demonstrated potential as cryogenic sensors for quench detection in HTS applications. But determining an appropriate threshold value for the central wavelength shift (Δλ) in quench detection remains a question to be addressed. In this paper, both single superconducting tapes and stacked tapes, which serve as the fundamental building blocks of HTS cables, are investigated. The time delay of the FBG sensor is demonstrated to be shorter than that of voltage taps when a hotspot occurs at the grating location. The Δλ corresponding to quench temperature—the threshold examined in this study—decreases as the distance from the hotspot increases. The FBG can effectively respond to a quench event more quickly than voltage, when the distance from the hot spot is less than 10 mm.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Experimental Studies on Quench Detection of Stacked REBCO Tapes Using Fiber Bragg Gratings
The normal zone propagation velocity (NZPV) in high-temperature superconductors (HTS) is two to three orders of magnitude lower than that in low-temperature superconductors (LTS). This slow quench propagation poses a critical challenge for quench detection in HTS applications. Fiber Bragg Grating (FBG) sensors have demonstrated potential as cryogenic sensors for quench detection in HTS applications. But determining an appropriate threshold value for the central wavelength shift (Δλ) in quench detection remains a question to be addressed. In this paper, both single superconducting tapes and stacked tapes, which serve as the fundamental building blocks of HTS cables, are investigated. The time delay of the FBG sensor is demonstrated to be shorter than that of voltage taps when a hotspot occurs at the grating location. The Δλ corresponding to quench temperature—the threshold examined in this study—decreases as the distance from the hotspot increases. The FBG can effectively respond to a quench event more quickly than voltage, when the distance from the hot spot is less than 10 mm.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Impact of Different Nonlinear E-J Relations on the Solvability and Convergence of High-Temperature Superconductor Quench Simulations
The current sharing process and increase in the electric field are closely related to the E-J relation during the quench of high-temperature superconductor (HTS). E-J power-law relation of the type E = Ec(J/Jc)n is widely used in modeling the dynamics of HTS, with Ec typically defined as 10−4 V/m, corresponding with the electric field when the current density J equals the critical current density Jc. This value is much lower than the electric field within a 40-μm-thick copper stabilizer carrying a current greater than 10 A, as well as the average electric field observed in the quenching zone during experiments. It means the current density is far greater than the critical current density when quench happens. The high ratio of J/Jc along with the E-J power-law relation brings difficulty in the convergence of the numerical model. This paper presented the comparison of the numerical simulation of the quench propagation problem in a single tape model with three nonlinearity E-J relations. The comparison reveals that one of these relations, in particular, significantly enhances the solvability and convergence of the quench model while resulting in smaller relative errors.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Impact of Different Nonlinear E-J Relations on the Solvability and Convergence of High-Temperature Superconductor Quench Simulations
The current sharing process and increase in the electric field are closely related to the E-J relation during the quench of high-temperature superconductor (HTS). E-J power-law relation of the type E = Ec(J/Jc)n is widely used in modeling the dynamics of HTS, with Ec typically defined as 10−4 V/m, corresponding with the electric field when the current density J equals the critical current density Jc. This value is much lower than the electric field within a 40-μm-thick copper stabilizer carrying a current greater than 10 A, as well as the average electric field observed in the quenching zone during experiments. It means the current density is far greater than the critical current density when quench happens. The high ratio of J/Jc along with the E-J power-law relation brings difficulty in the convergence of the numerical model. This paper presented the comparison of the numerical simulation of the quench propagation problem in a single tape model with three nonlinearity E-J relations. The comparison reveals that one of these relations, in particular, significantly enhances the solvability and convergence of the quench model while resulting in smaller relative errors.
- 7 November 2024
- Published by Springer Nature in Journal of Low Temperature Physics
- Vol. 218 (3-4) , 146-165
Design and Improvement of Quench Protection for A 3 T MRI Superconducting Magnet
- 7 November 2024
- Published by Springer Nature in Journal of Low Temperature Physics
- Vol. 218 (3-4) , 146-165
Design and Improvement of Quench Protection for A 3 T MRI Superconducting Magnet
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (9) , 1-10
Modeling of the Stacked High-Temperature Superconducting Cable-in-Conduit Conductor for High-Field Magnet Applications
High-temperature superconducting (HTS) materials hold great promise for advancing large-scale high-field magnets. This paper presents a comprehensive study on the design, fabrication, and performance evaluation of stacked HTS cable-in-conduit conductors (CICCs) for a prospective 55 T hybrid magnet, conducted through finite element modeling. The CICC configuration features a central copper core surrounded by straight-slotted channels filled with solder and rare-earth barium copper oxide (REBCO) tapes, encased in copper and stainless steel (SS) jackets. Key aspects investigated include critical current characteristics, stress-strain, bending behaviors, and thermal performance of the stacked HTS CICCs. Critical current evaluation and tensile/compressive stress at 77 K and 4.2 K self-fields, along with analysis of responses to varying magnetic induction intensities and orientations, is conducted. Strain distribution in the conductor at different bending radii and temperature distribution along the conductor under various cooling processing are analyzed. The study involves numerical modeling of conductor behavior under diverse magnetic fields, mechanical loading conditions, and thermal environments. Additionally, critical current analysis, strain distribution assessment, and cooling performance evaluation offer valuable insights into the operational capabilities of the conductor. The model evaluates electromagnetic, mechanical, and low-temperature properties of the stacked HTS CICC, suggesting its suitability for HTS coils within large-scale magnets following optimization. These findings offer insights crucial for designing and optimizing CICCs for high-field magnet applications.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (9) , 1-10
Modeling of the Stacked High-Temperature Superconducting Cable-in-Conduit Conductor for High-Field Magnet Applications
High-temperature superconducting (HTS) materials hold great promise for advancing large-scale high-field magnets. This paper presents a comprehensive study on the design, fabrication, and performance evaluation of stacked HTS cable-in-conduit conductors (CICCs) for a prospective 55 T hybrid magnet, conducted through finite element modeling. The CICC configuration features a central copper core surrounded by straight-slotted channels filled with solder and rare-earth barium copper oxide (REBCO) tapes, encased in copper and stainless steel (SS) jackets. Key aspects investigated include critical current characteristics, stress-strain, bending behaviors, and thermal performance of the stacked HTS CICCs. Critical current evaluation and tensile/compressive stress at 77 K and 4.2 K self-fields, along with analysis of responses to varying magnetic induction intensities and orientations, is conducted. Strain distribution in the conductor at different bending radii and temperature distribution along the conductor under various cooling processing are analyzed. The study involves numerical modeling of conductor behavior under diverse magnetic fields, mechanical loading conditions, and thermal environments. Additionally, critical current analysis, strain distribution assessment, and cooling performance evaluation offer valuable insights into the operational capabilities of the conductor. The model evaluates electromagnetic, mechanical, and low-temperature properties of the stacked HTS CICC, suggesting its suitability for HTS coils within large-scale magnets following optimization. These findings offer insights crucial for designing and optimizing CICCs for high-field magnet applications.
- Open Access
- 2 August 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (9) , 095023
Thermal degradation analysis and optimization of controlled heat treatment for stacked high temperature superconducting tapes
High temperature superconducting (HTS) tapes have crucial applications for generating high magnetic fields with minimal power input. Given a single tape has a limited current-carrying capacity, stacked tapes are common, fabricated through methods like solder soldering or epoxy impregnation requiring heat treatment. In this work, we have investigated the efficient region for vacuum heat treatment applicable of commercial HTS tapes, analysed the thermal degradation principles and accordingly proposed a controlled heat treatment process for stacked HTS tapes to achieve more precise regulation of the critical current ( I c ). This heat treatment process was explored using a specialized multi-temperature zone vacuum system. Critical parameters in this process include heat treatment temperature, duration and pressure on the tape. A series of experiments were conducted at 77 K in a self-field to investigate how these parameters affect the superconductivity performance of stacked HTS tapes. Based on the experimental results, an optimal heat treatment process has been proposed. Under the current process, with the heat treatment temperature set at 200 °C, duration at 20 min, and pressure on the tape at 12 MPa, the samples exhibit favourable properties characterized by a smooth and neat appearance without defects such as pinholes or false soldering, and the superconductivity performance can be consistently maintained at more than 97%. The obtained measurements were compared with simulated results, demonstrating an error margin within 0.5%. Moreover, precise control of I c is achieved, tailored to tape and stacking specifications, allowing manageable degradation as required. This heat treatment process for stacked HTS tapes holds significant importance, especially in the context of designing cable-in-conduit conductors fabricated with stacked HTS tapes. It serves as a valuable reference for further advancements in this field.
- 2 August 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (9) , 095023
Open AccessThermal degradation analysis and optimization of controlled heat treatment for stacked high temperature superconducting tapes
High temperature superconducting (HTS) tapes have crucial applications for generating high magnetic fields with minimal power input. Given a single tape has a limited current-carrying capacity, stacked tapes are common, fabricated through methods like solder soldering or epoxy impregnation requiring heat treatment. In this work, we have investigated the efficient region for vacuum heat treatment applicable of commercial HTS tapes, analysed the thermal degradation principles and accordingly proposed a controlled heat treatment process for stacked HTS tapes to achieve more precise regulation of the critical current ( I c ). This heat treatment process was explored using a specialized multi-temperature zone vacuum system. Critical parameters in this process include heat treatment temperature, duration and pressure on the tape. A series of experiments were conducted at 77 K in a self-field to investigate how these parameters affect the superconductivity performance of stacked HTS tapes. Based on the experimental results, an optimal heat treatment process has been proposed. Under the current process, with the heat treatment temperature set at 200 °C, duration at 20 min, and pressure on the tape at 12 MPa, the samples exhibit favourable properties characterized by a smooth and neat appearance without defects such as pinholes or false soldering, and the superconductivity performance can be consistently maintained at more than 97%. The obtained measurements were compared with simulated results, demonstrating an error margin within 0.5%. Moreover, precise control of I c is achieved, tailored to tape and stacking specifications, allowing manageable degradation as required. This heat treatment process for stacked HTS tapes holds significant importance, especially in the context of designing cable-in-conduit conductors fabricated with stacked HTS tapes. It serves as a valuable reference for further advancements in this field.