Adam Tater
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adam Tater has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Jan Pařez
Center of Aviation and Space Research, Faculty of Mechanical Engineering, Czech Technical University in Prague, Prague, Czech Republic
1 shared publication Patrik Kovář
Center of Aviation and Space Research, Faculty of Mechanical Engineering, Czech Technical University in Prague, Jugoslávských partyzán˚u1580/3, 16000, Prague 6, Czech Republic
1 shared publication- Patrik Kovář
Center of Aviation and Space Research, Faculty of Mechanical Engineering, Czech Technical University in Prague, Prague, Czech Republic
1 shared publication Pavel Mačák
Center of Aviation and Space Research, Faculty of Mechanical Engineering, Czech Technical University in Prague, Jugoslávských partyzán˚u1580/3, 16000, Prague 6, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 31 December 2023
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 63 (6) , 430–438
Prediction of temperature field distribution in a gas turbine using a higher order neural network
This paper presents the prediction of temperature field distribution in a single annular section using an artificial neural network (ANN). This temperature distribution is non-uniform on the outer tube due to continuous natural convection and radiation caused by the homogeneous steady-state heating of the inner tube, which represents the hot gas flow path through the turbine. The outer tube represents the case of a gas turbine. This temperature is important for the electronic components attached to the engine or the overall engine deformation. The presented approach allows for a quick estimation of the temperature distribution without the need to perform time consuming computational fluid dynamics (CFD) simulations. This can greatly accelerate the design and development of gas turbines. A machine learning approach is applied to an extensive set of CFD simulations under different operating conditions and geometry setups.
- 31 December 2023
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 63 (6) , 430–438
Open AccessPrediction of temperature field distribution in a gas turbine using a higher order neural network
This paper presents the prediction of temperature field distribution in a single annular section using an artificial neural network (ANN). This temperature distribution is non-uniform on the outer tube due to continuous natural convection and radiation caused by the homogeneous steady-state heating of the inner tube, which represents the hot gas flow path through the turbine. The outer tube represents the case of a gas turbine. This temperature is important for the electronic components attached to the engine or the overall engine deformation. The presented approach allows for a quick estimation of the temperature distribution without the need to perform time consuming computational fluid dynamics (CFD) simulations. This can greatly accelerate the design and development of gas turbines. A machine learning approach is applied to an extensive set of CFD simulations under different operating conditions and geometry setups.
- Open Access
- 23 December 2023
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 71 (6) , 148873
Mesh suitability for CFD simulations performed on axial compressor airfoil cascades
In the presented paper, two different meshing strategies are compared to show the accuracy advantage of properly constructed mesh. For this purpose, it was necessary to automatize simulation process, in order to perform a number of calculations without the necessity of user interaction. Later, a method of results extrapolation as well as a way of judging mesh quality are introduced for more throughout comparison of presented discretization strategies. The latter method, called grid convergence index, is also used to calculate probability range of accurate result. To conclude, outcomes of this study are in agreement with general opinon on pracitces for an accurate CFD result. Structured O-type mesh with refinement at wall boundaries (often referred to as “inflation layers”) performs better than simple free mesh.
- 23 December 2023
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 71 (6) , 148873
Open AccessMesh suitability for CFD simulations performed on axial compressor airfoil cascades
In the presented paper, two different meshing strategies are compared to show the accuracy advantage of properly constructed mesh. For this purpose, it was necessary to automatize simulation process, in order to perform a number of calculations without the necessity of user interaction. Later, a method of results extrapolation as well as a way of judging mesh quality are introduced for more throughout comparison of presented discretization strategies. The latter method, called grid convergence index, is also used to calculate probability range of accurate result. To conclude, outcomes of this study are in agreement with general opinon on pracitces for an accurate CFD result. Structured O-type mesh with refinement at wall boundaries (often referred to as “inflation layers”) performs better than simple free mesh.