Christoph Schmid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Christoph Schmid has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Dieter Koelle
Universität Tübingen
10 shared publications - Reinhold Kleiner
Universität Tübingen
10 shared publications - Edward Goldobin
Universität Tübingen
6 shared publications - Benedikt Hampel
National Institute of Standards and Technology 1 , Boulder, Colorado 80305
5 shared publications - Max Pröpper
Institut fr Elektrische Messtechnik und Grundlagen der Elektrotechnik, Technische Universitt Braunschweig, Braunschweig, Germany
5 shared publications - Meinhard Schilling
Institut fr Elektrische Messtechnik und Grundlagen der Elektrotechnik, Technische Universitt Braunschweig, Braunschweig, Germany
5 shared publications
Latest Publications
- Open Access
- 26 October 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (4) , 044076
Tailoring the properties of YBa 2 Cu 3 O 7 − δ thin films by 30-keV He + irradiation: An enabling route to superconducting-device nanopatterning
Focused helium ion beam (He-FIB) irradiation with 30-keV ions is a key tool for nanoscale patterning and defect engineering in high-transition temperature ( T c ) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30-keV He + ion exposure on the electric transport and superconducting properties of epitaxial YBa 2 Cu 3 O 7 − δ (YBCO) thin films. X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating in predominant amorphization at the highest fluence of 1 × 10 16 cm − 2 . Raman spectra exhibit increasing disorder while lacking signatures of oxygen depletion, indicating that irradiation mainly generates oxygen-related Frenkel defects rather than changing the carrier concentration. Consistently, with increasing fluence, the normal-state resistivity ρ N ( T ) at temperature T above T c increases strongly, while ∂ ρ N / ∂ T remains nearly unchanged at moderate fluence. The suppression of T c is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4.5 × 10 15 cm − 2 . The anisotropic upper critical fields decrease approximately exponentially with increasing fluence; the vortex activation energy is reduced, and the anisotropy drops, in contrast to oxygen-depleted YBCO. Hall-angle analysis confirms a nearly constant carrier density but a systematic increase in defect scattering and reduced mobility, consistent with a crossover toward the dirty limit at high fluence. These results establish quantitative fluence thresholds and a practical operational window for He-FIB nanopatterning of YBCO quantum circuits.
- 26 October 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (4) , 044076
Open AccessTailoring the properties of YBa 2 Cu 3 O 7 − δ thin films by 30-keV He + irradiation: An enabling route to superconducting-device nanopatterning
Focused helium ion beam (He-FIB) irradiation with 30-keV ions is a key tool for nanoscale patterning and defect engineering in high-transition temperature ( T c ) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30-keV He + ion exposure on the electric transport and superconducting properties of epitaxial YBa 2 Cu 3 O 7 − δ (YBCO) thin films. X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating in predominant amorphization at the highest fluence of 1 × 10 16 cm − 2 . Raman spectra exhibit increasing disorder while lacking signatures of oxygen depletion, indicating that irradiation mainly generates oxygen-related Frenkel defects rather than changing the carrier concentration. Consistently, with increasing fluence, the normal-state resistivity ρ N ( T ) at temperature T above T c increases strongly, while ∂ ρ N / ∂ T remains nearly unchanged at moderate fluence. The suppression of T c is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4.5 × 10 15 cm − 2 . The anisotropic upper critical fields decrease approximately exponentially with increasing fluence; the vortex activation energy is reduced, and the anisotropy drops, in contrast to oxygen-depleted YBCO. Hall-angle analysis confirms a nearly constant carrier density but a systematic increase in defect scattering and reduced mobility, consistent with a crossover toward the dirty limit at high fluence. These results establish quantitative fluence thresholds and a practical operational window for He-FIB nanopatterning of YBCO quantum circuits.
- Open Access
- 16 September 2026
- Published by Wiley in Advanced Science
Structural Changes and Transport Properties of YBa 2 Cu 3 O 7 Locally Modified by a He + Focused Ion Beam
Irradiation of a material with ions can cause various defects that can lead to structural phase transitions and the modification of the material's properties. Here we study the irradiation of epitaxially grown thin films of the high‐temperature superconductor YBa 2 Cu 3 O 7 with 30 keV ions which leads to the expansion of the crystal lattice, degradation of superconducting properties, and eventual transition to an insulator. Fabrication of such insulating regions with a focused He‐Ion beam with a spot size of nm is a powerful technique for fabrication of superconducting nano‐devices. Using low‐temperature resistivity measurements, diffraction with a nanofocused X‐ray beam and atomic force microscopy, we investigated how the structure and the electric transport properties of YBa 2 Cu 3 O 7 depend on the irradiation dose in a range 10–100 ions/nm 2 and on the lateral size of the irradiated area in a range 30–5000 nm.
- 16 September 2026
- Published by Wiley in Advanced Science
Open AccessStructural Changes and Transport Properties of YBa 2 Cu 3 O 7 Locally Modified by a He + Focused Ion Beam
Irradiation of a material with ions can cause various defects that can lead to structural phase transitions and the modification of the material's properties. Here we study the irradiation of epitaxially grown thin films of the high‐temperature superconductor YBa 2 Cu 3 O 7 with 30 keV ions which leads to the expansion of the crystal lattice, degradation of superconducting properties, and eventual transition to an insulator. Fabrication of such insulating regions with a focused He‐Ion beam with a spot size of nm is a powerful technique for fabrication of superconducting nano‐devices. Using low‐temperature resistivity measurements, diffraction with a nanofocused X‐ray beam and atomic force microscopy, we investigated how the structure and the electric transport properties of YBa 2 Cu 3 O 7 depend on the irradiation dose in a range 10–100 ions/nm 2 and on the lateral size of the irradiated area in a range 30–5000 nm.
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (7) , 1500910
Design and Performance of a 10-GHz HTS He-FIB JJ Mixer on LSAT Substrate
This paper presents a compact, single-ended high-temperature superconducting (HTS) helium-focused ion beam (He-FIB) Josephson junction (JJ) mixer. The planar circuit is fabricated from a thin film layer of YBa2Cu3O7-x deposited on a 10 mm × 10 mm Lanthanum Strontium Aluminium Tantalate (LSAT) substrate. A comprehensive six-step microstrip design methodology is outlined, detailing the JJ's physical geometries, high frequency and DC grounding, impedance matching, and filtering networks. The complete microstrip topology is designed to achieve an approximate radio frequency (RF) input passband between 9.9 GHz to 10.6 GHz with high out-of-band isolation, a single local oscillator (LO) resonance at 11.54 GHz and an intermediate frequency (IF) lowpass cut-off at 2.3 GHz. The proposed RF impedance matching network is uniquely designed to mitigate the significant performance limitation associated with normal resistances ($\rm{R}_\rm{n}$) scatter observed in HTS JJs. By implementing the proposed design methodology, a stable percentage bandwidth and $\rm{S}_{11}$ $\leq$ -10 dB is maintained between ${\mathit{R}}_\rm{n} =$ 5 $\Omega$ to 10 $\Omega$, which coincides with the fabrication variance for He-FIB JJs. The HTS mixer is manufactured and its DC and high frequency behaviours are characterised at 6 K, 10 K, 20 K, 30 K, and 40 K. The measured ${\mathit{R}}_\rm{n}$ is 9.77 $\Omega$, which significantly deviated from the predicted value of 5 $\Omega$, emphasising the importance of the adaptability and versatility of the implemented impedance matching network. Exposed to the lowest measured temperature, the HTS mixer exhibited a maximum conversion gain of -4.93 dB which demonstrates the potential capabilities in He-FIB induced barrier JJs on LSAT substrates as frequency mixers.
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (7) , 1500910
Design and Performance of a 10-GHz HTS He-FIB JJ Mixer on LSAT Substrate
This paper presents a compact, single-ended high-temperature superconducting (HTS) helium-focused ion beam (He-FIB) Josephson junction (JJ) mixer. The planar circuit is fabricated from a thin film layer of YBa2Cu3O7-x deposited on a 10 mm × 10 mm Lanthanum Strontium Aluminium Tantalate (LSAT) substrate. A comprehensive six-step microstrip design methodology is outlined, detailing the JJ's physical geometries, high frequency and DC grounding, impedance matching, and filtering networks. The complete microstrip topology is designed to achieve an approximate radio frequency (RF) input passband between 9.9 GHz to 10.6 GHz with high out-of-band isolation, a single local oscillator (LO) resonance at 11.54 GHz and an intermediate frequency (IF) lowpass cut-off at 2.3 GHz. The proposed RF impedance matching network is uniquely designed to mitigate the significant performance limitation associated with normal resistances ($\rm{R}_\rm{n}$) scatter observed in HTS JJs. By implementing the proposed design methodology, a stable percentage bandwidth and $\rm{S}_{11}$ $\leq$ -10 dB is maintained between ${\mathit{R}}_\rm{n} =$ 5 $\Omega$ to 10 $\Omega$, which coincides with the fabrication variance for He-FIB JJs. The HTS mixer is manufactured and its DC and high frequency behaviours are characterised at 6 K, 10 K, 20 K, 30 K, and 40 K. The measured ${\mathit{R}}_\rm{n}$ is 9.77 $\Omega$, which significantly deviated from the predicted value of 5 $\Omega$, emphasising the importance of the adaptability and versatility of the implemented impedance matching network. Exposed to the lowest measured temperature, the HTS mixer exhibited a maximum conversion gain of -4.93 dB which demonstrates the potential capabilities in He-FIB induced barrier JJs on LSAT substrates as frequency mixers.
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Toward a Voltage Standard Using YBa 2 Cu 3 O 7-x Josephson Junction Arrays Fabricated by He-FIB
Recent results with shunted YBa2Cu3O7-x Josephson junctions (JJs) fabricated using direct-writing by helium-focused ion beam (He-FIB) demonstrate that this technology is useful to achieve a YBa2Cu3O7-x voltage standard. By adding a shunt resistor via a subsequent lift-off step, the $\rm{{\mathit{R}}}_\rm{n}$ value and thereby the spread of the JJs can be reduced. These results were achieved with one large shunt across multiple JJs. This study presents different designs of shunt resistors, which allow measuring the JJs individually. The different shunt resistor designs are described and evaluated by comparing measurement results without and with the shunt resistor. These show the desired effect of controlling $\rm{{\mathit{R}}}_\rm{n}$, but also a change in $\rm{{\mathit{I}}}_\rm{c}$ is visible. The spread in parameters is investigated both without and with shunt resistors. Shapiro steps at gigahertz frequencies are presented for single JJs. The study concludes with a comparative measurement between a YBa2Cu3O7-x He-FIB JJ and a Josephson Arbitrary Waveform Synthesizer from PTB Braunschweig, showing a deviation of 0.05% and thus demonstrating its potential applicability.
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Toward a Voltage Standard Using YBa 2 Cu 3 O 7-x Josephson Junction Arrays Fabricated by He-FIB
Recent results with shunted YBa2Cu3O7-x Josephson junctions (JJs) fabricated using direct-writing by helium-focused ion beam (He-FIB) demonstrate that this technology is useful to achieve a YBa2Cu3O7-x voltage standard. By adding a shunt resistor via a subsequent lift-off step, the $\rm{{\mathit{R}}}_\rm{n}$ value and thereby the spread of the JJs can be reduced. These results were achieved with one large shunt across multiple JJs. This study presents different designs of shunt resistors, which allow measuring the JJs individually. The different shunt resistor designs are described and evaluated by comparing measurement results without and with the shunt resistor. These show the desired effect of controlling $\rm{{\mathit{R}}}_\rm{n}$, but also a change in $\rm{{\mathit{I}}}_\rm{c}$ is visible. The spread in parameters is investigated both without and with shunt resistors. Shapiro steps at gigahertz frequencies are presented for single JJs. The study concludes with a comparative measurement between a YBa2Cu3O7-x He-FIB JJ and a Josephson Arbitrary Waveform Synthesizer from PTB Braunschweig, showing a deviation of 0.05% and thus demonstrating its potential applicability.
- 15 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-6
Shunting YBa 2 Cu 3 O 7-x Josephson Junctions and Arrays Fabricated by He-FIB
Fabrication of YBa2Cu3O7-x Josephson junctions (JJs) using a direct-write helium-focused helium ion beam (He-FIB) technique has great potential for various applications due to tunable JJ parameters and arbitrary positioning. This technique allows placing multiple JJs in series to create JJ arrays. They could be used as a voltage standard that is operated at higher temperatures and driving frequencies than the currently used niobium-based JJ arrays. Small YBa2Cu3O7-x He-FIB JJ arrays with superposed Shapiro steps for up to three JJs have already been demonstrated. The number of JJs in the array was limited by the parameter spread of the individual JJs. This study presents WRspice simulations of JJ arrays, which indicate that the normal state resistance $R$n is the most crucial parameter to achieve flat Shapiro steps in JJ arrays. The idea of adding a shunt resistor to the JJ array to deal with the spread in $R$n values is investigated. A new design for GHz frequencies is presented, and the fabrication process is described. The properties of the shunt resistor are evaluated by van der Pauw measurements. Comparison of measurements with and without shunt resistor shows the desired effect of changing the total resistance of the JJ array while maintaining the critical current value. Finally, measurements of JJ arrays demonstrating superposed Shapiro steps at 20 k at GHz frequencies are presented.
- 15 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (4) , 1-6
Shunting YBa 2 Cu 3 O 7-x Josephson Junctions and Arrays Fabricated by He-FIB
Fabrication of YBa2Cu3O7-x Josephson junctions (JJs) using a direct-write helium-focused helium ion beam (He-FIB) technique has great potential for various applications due to tunable JJ parameters and arbitrary positioning. This technique allows placing multiple JJs in series to create JJ arrays. They could be used as a voltage standard that is operated at higher temperatures and driving frequencies than the currently used niobium-based JJ arrays. Small YBa2Cu3O7-x He-FIB JJ arrays with superposed Shapiro steps for up to three JJs have already been demonstrated. The number of JJs in the array was limited by the parameter spread of the individual JJs. This study presents WRspice simulations of JJ arrays, which indicate that the normal state resistance $R$n is the most crucial parameter to achieve flat Shapiro steps in JJ arrays. The idea of adding a shunt resistor to the JJ array to deal with the spread in $R$n values is investigated. A new design for GHz frequencies is presented, and the fabrication process is described. The properties of the shunt resistor are evaluated by van der Pauw measurements. Comparison of measurements with and without shunt resistor shows the desired effect of changing the total resistance of the JJ array while maintaining the critical current value. Finally, measurements of JJ arrays demonstrating superposed Shapiro steps at 20 k at GHz frequencies are presented.
- 5 September 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (3)
Nonvolatile multistate electrothermal resistive switching in a strongly correlated insulator thin-film device
- 5 September 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (3)
Nonvolatile multistate electrothermal resistive switching in a strongly correlated insulator thin-film device
- 22 July 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (1)
Josephson diode fabricated by focused-helium-ion-beam irradiation- 22 July 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (1)
Josephson diode fabricated by focused-helium-ion-beam irradiation- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
High-$T_{\mathrm{c}}$ Josephson Junction Arrays Fabricated by He-FIB
The development of a fabrication process for Josephson junctions (JJs) using a direct-write helium-focused ion beam (He-FIB) technique provides the opportunity to control parameters such as the critical current $I_{\mathrm{c}}$ and normal-state resistance $R_{\mathrm{n}}$ of individual JJs in YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJ arrays. Such arrays could be used as a voltage calibration standard that is operated at higher temperatures and higher driving frequencies than the currently used niobium JJ arrays. This study presents the fabrication process of 79 YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJs in a meander array design using a direct writing He-FIB process with the same irradiation dose for all JJs. In this design, each of the JJs can be measured individually, and adjacent JJs that exhibit similar and suitable parameters for a voltage standard array can be measured in series. The scattering of the JJ parameters was investigated at 5 K and resulted in a spread in $I_{\mathrm{c}}$ of about 60% and in $R_{\mathrm{n}}$ of 25%. However, a couple of subarrays with a spread lower than 10% could be found. In addition, these JJ subarrays were irradiated with high-frequency radiation in the GHz and THz range at a temperature of 20 K and synchronization of up to three JJs was observed in both frequency ranges.
- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
High-$T_{\mathrm{c}}$ Josephson Junction Arrays Fabricated by He-FIB
The development of a fabrication process for Josephson junctions (JJs) using a direct-write helium-focused ion beam (He-FIB) technique provides the opportunity to control parameters such as the critical current $I_{\mathrm{c}}$ and normal-state resistance $R_{\mathrm{n}}$ of individual JJs in YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJ arrays. Such arrays could be used as a voltage calibration standard that is operated at higher temperatures and higher driving frequencies than the currently used niobium JJ arrays. This study presents the fabrication process of 79 YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJs in a meander array design using a direct writing He-FIB process with the same irradiation dose for all JJs. In this design, each of the JJs can be measured individually, and adjacent JJs that exhibit similar and suitable parameters for a voltage standard array can be measured in series. The scattering of the JJ parameters was investigated at 5 K and resulted in a spread in $I_{\mathrm{c}}$ of about 60% and in $R_{\mathrm{n}}$ of 25%. However, a couple of subarrays with a spread lower than 10% could be found. In addition, these JJ subarrays were irradiated with high-frequency radiation in the GHz and THz range at a temperature of 20 K and synchronization of up to three JJs was observed in both frequency ranges.
- Open Access
- 17 July 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (1) , 014043
Vortex matching at 6 T in thin films by imprinting a 20-nm periodic pinning array with a focused helium-ion beamControlled engineering of vortex pinning sites in copper-oxide superconductors is a critical issue in manufacturing devices based on magnetic flux quanta. To address this, we employed a focused -ion beam (-FIB) to irradiate thin films and create ultradense hexagonal arrays of defects with lattice spacings as small as 20 nm. Critical current and magnetoresistance measurements demonstrate efficient pinning by a matching field of 6 T visible in a huge temperature range from the critical temperature down to 2 K. These results show that -FIB irradiation provides excellent opportunities for the development and application of superconducting fluxonic devices based on Abrikosov vortices. In particular, our findings suggest that such devices can operate at temperatures far below , where superconductivity is robust.- 17 July 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (1) , 014043
Open AccessVortex matching at 6 T in thin films by imprinting a 20-nm periodic pinning array with a focused helium-ion beamControlled engineering of vortex pinning sites in copper-oxide superconductors is a critical issue in manufacturing devices based on magnetic flux quanta. To address this, we employed a focused -ion beam (-FIB) to irradiate thin films and create ultradense hexagonal arrays of defects with lattice spacings as small as 20 nm. Critical current and magnetoresistance measurements demonstrate efficient pinning by a matching field of 6 T visible in a huge temperature range from the critical temperature down to 2 K. These results show that -FIB irradiation provides excellent opportunities for the development and application of superconducting fluxonic devices based on Abrikosov vortices. In particular, our findings suggest that such devices can operate at temperatures far below , where superconductivity is robust. - 12 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
THz Properties of He-FIB YBa2Cu3O7-x Josephson Junctions
Josephson junctions with customizable parameters, including critical current $I$ c and normal state resistance $R$ n , hold great promise across a wide range of applications. Notably, high-temperature superconductors like YBa 2 Cu 3 O 7-x have been interesting since their discovery due to their simplified cooling requirements. YBa 2 Cu 3 O 7-x Josephson junctions can operate within the terahertz (THz) frequency range, rendering them highly suitable for various applications. To maximize their suitability at these high frequencies, it is imperative to precisely determine their THz parameters. Helium focused ion beam (He-FIB) technology is a very promising fabrication method for customizable Josephson junctions. It allows precise control of the He-FIB dose during the fabrication of Josephson junctions and facilitates the fine-tuning of I c and R n . This study presents the fabrication process of YBa 2 Cu 3 O 7-x Josephson junctions using He-FIB irradiation and explores the variations of parameters with dose, evaluating their suitability within the THz range. Also, the scattering of parameters of He-FIB Josephson junctions fabricated with the same He-FIB dose is investigated. Additionally, we examine the high-frequency properties of such junctions and scrutinize the associated Shapiro steps within the THz frequency spectrum. We observe an exponential relationship between I c and the He-FIB dose. Moreover, Shapiro steps emerge under the influence of radiation spanning from 40 GHz to as high as 1.4 THz.
- 12 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
THz Properties of He-FIB YBa2Cu3O7-x Josephson Junctions
Josephson junctions with customizable parameters, including critical current $I$ c and normal state resistance $R$ n , hold great promise across a wide range of applications. Notably, high-temperature superconductors like YBa 2 Cu 3 O 7-x have been interesting since their discovery due to their simplified cooling requirements. YBa 2 Cu 3 O 7-x Josephson junctions can operate within the terahertz (THz) frequency range, rendering them highly suitable for various applications. To maximize their suitability at these high frequencies, it is imperative to precisely determine their THz parameters. Helium focused ion beam (He-FIB) technology is a very promising fabrication method for customizable Josephson junctions. It allows precise control of the He-FIB dose during the fabrication of Josephson junctions and facilitates the fine-tuning of I c and R n . This study presents the fabrication process of YBa 2 Cu 3 O 7-x Josephson junctions using He-FIB irradiation and explores the variations of parameters with dose, evaluating their suitability within the THz range. Also, the scattering of parameters of He-FIB Josephson junctions fabricated with the same He-FIB dose is investigated. Additionally, we examine the high-frequency properties of such junctions and scrutinize the associated Shapiro steps within the THz frequency spectrum. We observe an exponential relationship between I c and the He-FIB dose. Moreover, Shapiro steps emerge under the influence of radiation spanning from 40 GHz to as high as 1.4 THz.