Rafis Ilyasov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rafis Ilyasov has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Михаил Вячеславович Маркушев
Institute for Metals Superplasticity Problems, Russian Academy of Sciences, Ufa, Russia
3 shared publications - I. Sh. Valeev
Russian Academy of Sciences
2 shared publications - Oleg Sitdikov
Institute for Metals Superplasticity Problems Russian Academy of Science. 39, Khalturina St., Ufa. 450001, Russia
2 shared publications - Stanislav Vatslavovich Krymskiy
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
2 shared publications - A. Kh. Valeeva
Institute for Metals Superplasticity Problems, RAS
1 shared publication - Elena Avtokratova
Institute for Metals Superplasticity Problems Russian Academy of Science. 39, Khalturina St., Ufa. 450001, Russia
1 shared publication
Latest Publications
- Open Access
- 19 December 2025
- Published by University of Nis in Facta Universitatis, Series: Mechanical Engineering
- Vol. 23 (4) , 909-920
EFFECT OF ELECTRIC PULSING ON THE STRUCTURE, TEXTURE AND HARDNESS OF CRYOROLLED FINE-GRAIN COPPER
A synergy effect of cryorolling and high-dense electric pulsing on the structure, texture and hardness of fine-grain Cu is analyzed. More than twice Cu strengthening under rolling with 90% reduction at –196°С was caused by strong rolling texture and work-hardened nanostructure with ~300 nm crystallites and ~30% fraction of high-angle boundaries. Further single pulsing with current intensity Kj = 3.5×104 A2s/mm4 resulted in a static recovery and slight Cu softening due to the formation of a more equilibrium structure with lower dislocation density and lattice microstrain. Increasing Kj to 3.8×104 A2s/mm4 led to a sharp drop in the Cu hardness owing to continuous recrystallization and texture randomization. At Kj near 5.0×104 A2s/mm4 homogeneous ultrafine-grain structure with 1 μm defect free equiaxed grains and about 30% of twin boundaries is formed. Normal grain growth to 3 µm and gradual decrease of the Cu hardness were taking place at higher pulsing energies, up to 8.1×104 A2s/mm4.
- 19 December 2025
- Published by University of Nis in Facta Universitatis, Series: Mechanical Engineering
- Vol. 23 (4) , 909-920
Open AccessEFFECT OF ELECTRIC PULSING ON THE STRUCTURE, TEXTURE AND HARDNESS OF CRYOROLLED FINE-GRAIN COPPER
A synergy effect of cryorolling and high-dense electric pulsing on the structure, texture and hardness of fine-grain Cu is analyzed. More than twice Cu strengthening under rolling with 90% reduction at –196°С was caused by strong rolling texture and work-hardened nanostructure with ~300 nm crystallites and ~30% fraction of high-angle boundaries. Further single pulsing with current intensity Kj = 3.5×104 A2s/mm4 resulted in a static recovery and slight Cu softening due to the formation of a more equilibrium structure with lower dislocation density and lattice microstrain. Increasing Kj to 3.8×104 A2s/mm4 led to a sharp drop in the Cu hardness owing to continuous recrystallization and texture randomization. At Kj near 5.0×104 A2s/mm4 homogeneous ultrafine-grain structure with 1 μm defect free equiaxed grains and about 30% of twin boundaries is formed. Normal grain growth to 3 µm and gradual decrease of the Cu hardness were taking place at higher pulsing energies, up to 8.1×104 A2s/mm4.
- Open Access
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 4,p. 53-62
Combination of cryogenic deformation and electropulse processing as a way to produce ultrafine-grain metals
The data of a comparative analysis of the structure and hardness of pure metals with a face-centered cubic lattice – aluminum, nickel and copper, subjected to complex thermomechanical treatment (TMT), including isothermal cryogenic rolling at liquid nitrogen temperature and subsequent high-density electropulse treatment (EPT) were presented. The main stages, features and advantages of TMT, which first ensure strong work hardening of the processed material due to deformation at low temperatures and then its ultra-fast contact electropulse heating up to a specified temperature, were considered. A multi-level analysis of the metals structure evolution due to TMT was carried out using modern methods of scanning electron microscopy and X-ray diffractometry, recording a wide range of its linear and angular parameters. The kinetics and nature of the processes of the metals structure evolution under cryogenic rolling and EPT, their driving forces and controlling factors, as well as general patterns and temperature intervals of activation of the deformation structure recovery and recrystallization influenced by an electric pulse are identified and discussed. Based on the results of the analysis of the structural and mechanical behaviour of metals, it was concluded that the combination of severe plastic cryogenic deformation and a single-step treatment with ultrashort alternating current pulses is an effective way to obtain semi-finished products with controlled parameters of their structure and properties, including high-strength ultrafine-grain rolled products. At that the phenomenology and nature of the strengthening/softening of metals during cryogenic rolling and subsequent electropulsing are similar to those observed under cold rolling and furnace annealing.
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 4,p. 53-62
Open AccessCombination of cryogenic deformation and electropulse processing as a way to produce ultrafine-grain metals
The data of a comparative analysis of the structure and hardness of pure metals with a face-centered cubic lattice – aluminum, nickel and copper, subjected to complex thermomechanical treatment (TMT), including isothermal cryogenic rolling at liquid nitrogen temperature and subsequent high-density electropulse treatment (EPT) were presented. The main stages, features and advantages of TMT, which first ensure strong work hardening of the processed material due to deformation at low temperatures and then its ultra-fast contact electropulse heating up to a specified temperature, were considered. A multi-level analysis of the metals structure evolution due to TMT was carried out using modern methods of scanning electron microscopy and X-ray diffractometry, recording a wide range of its linear and angular parameters. The kinetics and nature of the processes of the metals structure evolution under cryogenic rolling and EPT, their driving forces and controlling factors, as well as general patterns and temperature intervals of activation of the deformation structure recovery and recrystallization influenced by an electric pulse are identified and discussed. Based on the results of the analysis of the structural and mechanical behaviour of metals, it was concluded that the combination of severe plastic cryogenic deformation and a single-step treatment with ultrashort alternating current pulses is an effective way to obtain semi-finished products with controlled parameters of their structure and properties, including high-strength ultrafine-grain rolled products. At that the phenomenology and nature of the strengthening/softening of metals during cryogenic rolling and subsequent electropulsing are similar to those observed under cold rolling and furnace annealing.
- Open Access
- 1 December 2021
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 11 (4) , 491-496
Structue and strength of fine-grain copper after cryorolling and single electrо-pulsing of different capacity
The effect of a treatment combining isothermal cryogenic rolling and single electro-pulsing on the structure and hardness of M1 grade copper with an initial grain size of 10 –15 μm was investigated.
- 1 December 2021
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 11 (4) , 491-496
Open AccessStructue and strength of fine-grain copper after cryorolling and single electrо-pulsing of different capacity
The effect of a treatment combining isothermal cryogenic rolling and single electro-pulsing on the structure and hardness of M1 grade copper with an initial grain size of 10 –15 μm was investigated.